15KV Inverter High Frequency High Voltage Generator Coil Arc Converter Boost DIY Kit

15Kv High Frequency Dc Voltage Arc Ignition Generator Inverter Boost Step Up 18650 Diy Kit U Core

15KV Inverter High Frequency High Voltage Generator Coil Arc Converter Boost DIY Kit

SKU:051108
$4.99


Note: This item is DIY Kit, not assembled. default with one PCB board.
Features:
◦This product is a booster coil production suite, the circuit is simple and reliable, with a professional line drawings, electronic research convenience enthusiasts
◦Uses: high school science experiment, electronic equipment, negative ion generator, scientific small production. This circuit is generated when the stable high frequency arc, high temperature, can easily ignite combustible materials, so it was called the plasma lighters
Parameter:
◦15KV transformer outside dimensions of approximately: 27×16×21mm
◦Input voltage: DC 3.7V-4.2V (limit 12v, easy to damage not recommended, this transformer is equally applicable to 12V input voltage, but requires a corresponding increase in the base of the feedback resistor to about 150Ω ~ 1.5KΩ, its resistance should be large to replace a small adjustment, or burned transistor or transformer)
◦Input Current: <2A
◦Output voltage: approximately 15KV (please pay attention to safety when used)
◦Output Current: ≤0.4A
◦High voltage bipolar ignition distance: ≤0.5 cm
◦When the product input termination 3.7V-4.2V power supply, the secondary high voltage output is not connected to high-voltage rectifier diodes and capacitors, output terminals levels ≤1.5cm long can produce purple high temperature arc, no crackling, but the temperature is very high , you can easily and instantly point cigarette paper, or even very thin wire burned Sparks (such as junior high school chemistry experiment thin wire in oxygen combustion scene, but not as good as oxygen so intense.)
Transformer structure:
There are two primary windings, a primary winding, a feedback winding, the secondary output of high pressure. Other: 15KV transformer designed for maximum output, limit output can not exceed 15KV, is one centimeter arc, a higher output voltage is likely to damage the transformer.
PCB board size: 4.2CM * 3.2CM * 0.16CM;
Installation Notes:
1). With the PCB board parts better production, in which the transformer line of thick line and thin line, this should pay attention to the other components by the board of silk symbols and parameters of welding on the line. Transformer board has done three pads, in which the middle of the pad hole is relatively large, the hole at the same time welding a thick enameled wire and a thin enameled wire, thick enameled wire and fine enameled wire do not use the same side, such as with the left Thick lines and the right side of the thin wire into or with the left side of the thin line and the right side of the thick line welding into, in short, do not use the same side of the thick lines and thin lines can be.
2). In order to prevent the output 2-wire distance too far, resulting in no-load, you can weld a 3P pin at the output.
3). After the success of the production, if the output access to a high-voltage capacitor and three high-voltage rectifier composed of voltage doubler circuit, you can produce DC high voltage, you can make anion generator, wiring diagram is as follows:
Package Included:
15VKE = 1 type step-up transformer x1
120 ohm resistance X 1
UF4007 ultra-fast recovery diode X 1
N20 transistor X 1
Heat sink X 1
M3 * 6 screws X 1
Boat switch X 1
3-Pin X 1






















trust seal
  • guaranteeQuality checked
  • Special gift cardsSpecial gift cards
  • Free return Within 60 days
  • Consultancy86-0755-85201155


Note: This item is DIY Kit, not assembled. default with one PCB board.
Features:
◦This product is a booster coil production suite, the circuit is simple and reliable, with a professional line drawings, electronic research convenience enthusiasts
◦Uses: high school science experiment, electronic equipment, negative ion generator, scientific small production. This circuit is generated when the stable high frequency arc, high temperature, can easily ignite combustible materials, so it was called the plasma lighters
Parameter:
◦15KV transformer outside dimensions of approximately: 27×16×21mm
◦Input voltage: DC 3.7V-4.2V (limit 12v, easy to damage not recommended, this transformer is equally applicable to 12V input voltage, but requires a corresponding increase in the base of the feedback resistor to about 150Ω ~ 1.5KΩ, its resistance should be large to replace a small adjustment, or burned transistor or transformer)
◦Input Current: <2A
◦Output voltage: approximately 15KV (please pay attention to safety when used)
◦Output Current: ≤0.4A
◦High voltage bipolar ignition distance: ≤0.5 cm
◦When the product input termination 3.7V-4.2V power supply, the secondary high voltage output is not connected to high-voltage rectifier diodes and capacitors, output terminals levels ≤1.5cm long can produce purple high temperature arc, no crackling, but the temperature is very high , you can easily and instantly point cigarette paper, or even very thin wire burned Sparks (such as junior high school chemistry experiment thin wire in oxygen combustion scene, but not as good as oxygen so intense.)
Transformer structure:
There are two primary windings, a primary winding, a feedback winding, the secondary output of high pressure. Other: 15KV transformer designed for maximum output, limit output can not exceed 15KV, is one centimeter arc, a higher output voltage is likely to damage the transformer.
PCB board size: 4.2CM * 3.2CM * 0.16CM;
Installation Notes:
1). With the PCB board parts better production, in which the transformer line of thick line and thin line, this should pay attention to the other components by the board of silk symbols and parameters of welding on the line. Transformer board has done three pads, in which the middle of the pad hole is relatively large, the hole at the same time welding a thick enameled wire and a thin enameled wire, thick enameled wire and fine enameled wire do not use the same side, such as with the left Thick lines and the right side of the thin wire into or with the left side of the thin line and the right side of the thick line welding into, in short, do not use the same side of the thick lines and thin lines can be.
2). In order to prevent the output 2-wire distance too far, resulting in no-load, you can weld a 3P pin at the output.
3). After the success of the production, if the output access to a high-voltage capacitor and three high-voltage rectifier composed of voltage doubler circuit, you can produce DC high voltage, you can make anion generator, wiring diagram is as follows:
Package Included:
15VKE = 1 type step-up transformer x1
120 ohm resistance X 1
UF4007 ultra-fast recovery diode X 1
N20 transistor X 1
Heat sink X 1
M3 * 6 screws X 1
Boat switch X 1
3-Pin X 1






















Purchasing & Delivery

Before you make your purchase, it’s helpful to know the measurements of the area you plan to place the furniture. You should also measure any doorways and hallways through which the furniture will pass to get to its final destination.
Picking up at the store
Shopify Shop requires that all products are properly inspected BEFORE you take it home to insure there are no surprises. Our team is happy to open all packages and will assist in the inspection process. We will then reseal packages for safe transport. We encourage all customers to bring furniture pads or blankets to protect the items during transport as well as rope or tie downs. Shopify Shop will not be responsible for damage that occurs after leaving the store or during transit. It is the purchaser’s responsibility to make sure the correct items are picked up and in good condition.
Delivery
Customers are able to pick the next available delivery day that best fits their schedule. However, to route stops as efficiently as possible, Shopify Shop will provide the time frame. Customers will not be able to choose a time. You will be notified in advance of your scheduled time frame. Please make sure that a responsible adult (18 years or older) will be home at that time.
In preparation for your delivery, please remove existing furniture, pictures, mirrors, accessories, etc. to prevent damages. Also insure that the area where you would like your furniture placed is clear of any old furniture and any other items that may obstruct the passageway of the delivery team. Shopify Shop will deliver, assemble, and set-up your new furniture purchase and remove all packing materials from your home. Our delivery crews are not permitted to move your existing furniture or other household items. Delivery personnel will attempt to deliver the purchased items in a safe and controlled manner but will not attempt to place furniture if they feel it will result in damage to the product or your home. Delivery personnel are unable to remove doors, hoist furniture or carry furniture up more than 3 flights of stairs. An elevator must be available for deliveries to the 4th floor and above.

Other Customers also buy:

  • 15Kv High Frequency Dc Voltage Arc Ignition Generator Inverter Boost Step Up 18650 Diy Kit U Core High Voltage Dc-Dc Boost Converter Step Up To Output 300V-1200V 400V 900V 1000V Adjustable Power Psu
    DC-DC High Voltage Boost Converter Input 3V-5V Output 1000V Power Supply Module
    $8.99
  • 15Kv High Frequency Dc Voltage Arc Ignition Generator Inverter Boost Step Up 18650 Diy Kit U Core Newest Multi-Function Mini Boost Module Step Up Board 5V/8V/9V/12V 1.5A Led Indicator Diy Electronic
    1PCS 3V 3.3V 5V 9V to 12V DC-DC Mini Boost Step Up Converter Volt Regulator
    $3.99
  • 15Kv High Frequency Dc Voltage Arc Ignition Generator Inverter Boost Step Up 18650 Diy Kit U Core Dc 3.3V 3.7V 5V 6V To 12V Step-Up Power Supply Boost Voltage Regulator Converter Step Up Module
    DC 3.3V 3.7V 5V 6V to 12V Step-up Power Supply Boost Voltage Regulator Converter
    $7.99
  • 15Kv High Frequency Dc Voltage Arc Ignition Generator Inverter Boost Step Up 18650 Diy Kit U Core 5Pcs Dc-Dc Boost Converter Step Up Module 1-5V To 5V 500Ma 600Ma Max For Arduino
    5PCS DC-DC Boost Converter Step Up Module 1-5V to 5V 500mA 600mA Max for Arduino
    $5.99
  • 15Kv High Frequency Dc Voltage Arc Ignition Generator Inverter Boost Step Up 18650 Diy Kit U Core Micro Usb 5V Lithium Battery Charger Step Up Protection Board Boost Power Module Li-Po Li-Ion 18650
    Lithium Power 5V Boost Step Up Battery Charger 18650 Protection Board Module
    $4.99