MOSFET Switch Module+1/4 Channel 1/4 Route MOSFET Button IRF520 IRF540 New

1 Channel Route Mosfet Button Irf540 Switch Sensor Expansion Module For Arduino Diy Electronic Pcb

MOSFET Switch Module+1/4 Channel 1/4 Route MOSFET Button IRF520 IRF540 New

SKU:010803
$5.99

MOSFET is an electronic device having a good switching characteristics, is widely used in the electronic switch circuit needs, such as switching power supplies and motor drives, and a lighting dimming. Relays are all very familiar with another module has switching characteristics, but because of the working principle of the relay is generally achieved by mechanical contact on and off purposes, which will inevitably lead to a very short switching times under the circumstances, the relay situation does not work, the other sounds when Baba contact switch in some cases is more annoying thing.

Use this module with for Arduino electronic building blocks 4 IRF540 MOSFET switches use the same, but changes to the way the original four. Use reference for Arduino 4-way switch IRF540 MOSFET Modules:

We designed this four-way MOSFET switch can provide up to four groups of electronic switches, were used to control different circuit modules. Affected MOSFET works, the electronic building blocks can be used to control the DC circuit, such as DC LED screen, etc., are not suitable for controlling the AC circuit. Under extreme circumstances of the MOSFET switch can be used to control 100V / 33A DC circuit, but control is recommended not less than the minimum DC voltage 9V.

The circuit is connected at one end of the wire is slightly controlled some trouble. To control a 12V LED lights, for example,
First, the positive (+) and negative (-) between the connected power;

Then connect the positive LED lights with the module connected to the positive (+),
LED lights with the anode connected to the switch 1 (S1) on;

If there are other LED lights with the need to control,
Just the same cathode lights with LED module is connected to the positive (+),
LED lights with the negative electrode in turn is connected to the switch 2 (S2), switch 3 (S3), the switch 4 (S4) on;

Connection control side is much simpler,
We only need a sensor cable,
The corresponding control port for Arduino sensor expansion board connected, you can control the 12V LED lights brought by For Arduino.
Experiment, we picked up two LED lights.
Test code as follows :
int s1Pin = 6;
int s2Pin = 7;
void setup() {
pinMode(s1Pin, OUTPUT);
pinMode(s2Pin, OUTPUT);
}
void loop() {
int i;
digitalWrite(s1Pin, HIGH);
digitalWrite(s2Pin, HIGH);
delay(500);
digitalWrite(s1Pin, LOW);
digitalWrite(s2Pin, LOW);
delay(500);
for (i = 0; i < 10; i ++) {
digitalWrite(s1Pin, HIGH);
delay(500);
digitalWrite(s1Pin, LOW);
delay(500);
}
for (i = 0; i < 100; i ++) {
digitalWrite(s2Pin, HIGH);
delay(50);
digitalWrite(s2Pin, LOW);
delay(50);
}
}

Package Included:

  • 1 x 1 Channel 1 Route MOSFET Button IRF540 + MOSFET Switch Module for Arduino TOP

trust seal
  • guaranteeQuality checked
  • Special gift cardsSpecial gift cards
  • Free return Within 60 days
  • Consultancy86-0755-85201155

MOSFET is an electronic device having a good switching characteristics, is widely used in the electronic switch circuit needs, such as switching power supplies and motor drives, and a lighting dimming. Relays are all very familiar with another module has switching characteristics, but because of the working principle of the relay is generally achieved by mechanical contact on and off purposes, which will inevitably lead to a very short switching times under the circumstances, the relay situation does not work, the other sounds when Baba contact switch in some cases is more annoying thing.

Use this module with for Arduino electronic building blocks 4 IRF540 MOSFET switches use the same, but changes to the way the original four. Use reference for Arduino 4-way switch IRF540 MOSFET Modules:

We designed this four-way MOSFET switch can provide up to four groups of electronic switches, were used to control different circuit modules. Affected MOSFET works, the electronic building blocks can be used to control the DC circuit, such as DC LED screen, etc., are not suitable for controlling the AC circuit. Under extreme circumstances of the MOSFET switch can be used to control 100V / 33A DC circuit, but control is recommended not less than the minimum DC voltage 9V.

The circuit is connected at one end of the wire is slightly controlled some trouble. To control a 12V LED lights, for example,
First, the positive (+) and negative (-) between the connected power;

Then connect the positive LED lights with the module connected to the positive (+),
LED lights with the anode connected to the switch 1 (S1) on;

If there are other LED lights with the need to control,
Just the same cathode lights with LED module is connected to the positive (+),
LED lights with the negative electrode in turn is connected to the switch 2 (S2), switch 3 (S3), the switch 4 (S4) on;

Connection control side is much simpler,
We only need a sensor cable,
The corresponding control port for Arduino sensor expansion board connected, you can control the 12V LED lights brought by For Arduino.
Experiment, we picked up two LED lights.
Test code as follows :
int s1Pin = 6;
int s2Pin = 7;
void setup() {
pinMode(s1Pin, OUTPUT);
pinMode(s2Pin, OUTPUT);
}
void loop() {
int i;
digitalWrite(s1Pin, HIGH);
digitalWrite(s2Pin, HIGH);
delay(500);
digitalWrite(s1Pin, LOW);
digitalWrite(s2Pin, LOW);
delay(500);
for (i = 0; i < 10; i ++) {
digitalWrite(s1Pin, HIGH);
delay(500);
digitalWrite(s1Pin, LOW);
delay(500);
}
for (i = 0; i < 100; i ++) {
digitalWrite(s2Pin, HIGH);
delay(50);
digitalWrite(s2Pin, LOW);
delay(50);
}
}

Package Included:

  • 1 x 1 Channel 1 Route MOSFET Button IRF540 + MOSFET Switch Module for Arduino TOP

Purchasing & Delivery

Before you make your purchase, it’s helpful to know the measurements of the area you plan to place the furniture. You should also measure any doorways and hallways through which the furniture will pass to get to its final destination.
Picking up at the store
Shopify Shop requires that all products are properly inspected BEFORE you take it home to insure there are no surprises. Our team is happy to open all packages and will assist in the inspection process. We will then reseal packages for safe transport. We encourage all customers to bring furniture pads or blankets to protect the items during transport as well as rope or tie downs. Shopify Shop will not be responsible for damage that occurs after leaving the store or during transit. It is the purchaser’s responsibility to make sure the correct items are picked up and in good condition.
Delivery
Customers are able to pick the next available delivery day that best fits their schedule. However, to route stops as efficiently as possible, Shopify Shop will provide the time frame. Customers will not be able to choose a time. You will be notified in advance of your scheduled time frame. Please make sure that a responsible adult (18 years or older) will be home at that time.
In preparation for your delivery, please remove existing furniture, pictures, mirrors, accessories, etc. to prevent damages. Also insure that the area where you would like your furniture placed is clear of any old furniture and any other items that may obstruct the passageway of the delivery team. Shopify Shop will deliver, assemble, and set-up your new furniture purchase and remove all packing materials from your home. Our delivery crews are not permitted to move your existing furniture or other household items. Delivery personnel will attempt to deliver the purchased items in a safe and controlled manner but will not attempt to place furniture if they feel it will result in damage to the product or your home. Delivery personnel are unable to remove doors, hoist furniture or carry furniture up more than 3 flights of stairs. An elevator must be available for deliveries to the 4th floor and above.

Other Customers also buy:

  • 1 Channel Route Mosfet Button Irf540 Switch Sensor Expansion Module For Arduino Diy Electronic Pcb 2 Wire 0.56\" Voltmeter LED Tube Digital DC4.5/4.7/5V-30V Voltage Panel Meter
    2 Wire 0.56\" Voltmeter LED Tube Digital DC4.5/4.7/5V-30V Voltage Panel Meter
    $5.99
  • 1 Channel Route Mosfet Button Irf540 Switch Sensor Expansion Module For Arduino Diy Electronic Pcb 18650 Battery Shield V8 Mobile Power Bank 3V/5V For Arduino Esp32 Esp8266 Wifi Expansion Module
    18650 Battery Shield V8 Mobile Power Bank 3V/5V for Arduino ESP32 ESP8266
    $5.99
  • 1 Channel Route Mosfet Button Irf540 Switch Sensor Expansion Module For Arduino Diy Electronic Pcb USB Charger Doctor Capacity Tester LCD Display Current Voltage Detector Meter
    USB Charger Doctor Capacity Tester LCD Display Current Voltage Detector Meter
    $7.99
  • 1 Channel Route Mosfet Button Irf540 Switch Sensor Expansion Module For Arduino Diy Electronic Pcb Esp32 Esp32S Wemos 4Pcs 18650 Lithium Battery Charging Shield 5V/3A 3V/1A Power Bank Expansion Board
    ESP32 ESP8266 4x 18650 Battery USB Power Bank Shield Holder V9 3V/5V
    $9.99
  • 1 Channel Route Mosfet Button Irf540 Switch Sensor Expansion Module For Arduino Diy Electronic Pcb 10Cm 40Pin Male To Male/ M-F/f-F Wire Jumper Breadboard Multicolored Dupont Ribbon Cables Kit For
    10cm 40pin Male to Male/ M-F/F-F Wire Jumper Breadboard Multicolored Dupont Ribbon Cables Kit for Arduino
    $5.99
  • 1 Channel Route Mosfet Button Irf540 Switch Sensor Expansion Module For Arduino Diy Electronic Pcb DC 5V 12V Jog Self lock Smart WiFi Wireless Switch Thet Relay Module APP Control Control Diy Electronic PCB Board
    DC 5V 12V Jog Self lock Smart WiFi Wireless Switch Thet Relay Module APP Control Control Diy Electronic PCB Board
    $8.99