5V/12V 2/3/4 Button Timer Delay Relay Motor Speed Temperature Controller+Buzzer
5V/12V 2/3/4 Button Timer Delay Relay Motor Speed Temperature Controller+Buzzer
SKU:100040
Regular price
$8.99
- guaranteeQuality checked
- Special gift cardsSpecial gift cards
- Free return Within 60 days
- Consultancy86-0755-85201155
1.Digital Display Delay Controller:(DC 12V with Buzzer 2 Button)
Product parameters
- Working voltage: DC12V (normal working voltage DC10V-16V)
- Signal source: DC4V~20V (usual power supply positive trigger, button, PNP sensor, PLC signal, etc.)
- Output capability: It can control devices within 30v5A or within 220v5A
- Quiescent current: 20mA, working current: 50mA
- Service life: more than 100,000 times;
- Working temperature: -40~85 °C;
- Net weight: about 26g
- Size: 64.2mm*34.8mm*18.5mm
Features
- Voltage input anti-reverse circuit, worry-free wiring. Signal input optocoupler isolation, strong anti-interference ability. Set the parameter to power off permanent memory. Powerful flash MCU online programming function, according to user needs can contact the manufacturer to customize the required functions.
Function introduction
- When the power is turned on, the trigger signal is received, the countdown starts, and the relay works. When the timer ends, the relay stops working, the time returns to the setting, and the next trigger signal is waited.
Instructions
- 1).Press K1 to enter the time setting, the hundred digit digital tube starts to flash; press K2 at this time, the hundred digits change; press K1 again, the ten digital tube starts to flash; press K2 at this time, the ten digits change; press again After K1, the digital tube starts to flash. At this time, press K2, the digit of the digit changes; press K1 again to exit the setting, and the digital tube no longer flashes.
- 2).When the digital tube is normally displayed, press K2, the decimal point is shifted, the decimal point is 0 to 999 seconds in ones digit, the decimal point is 0 to 99.9 seconds in ten digits, and the decimal point is 0 to 999 minutes; the time is set.
2.Digital Display Delay Controller:(DC 12V 3 Button)
Product parameters
Working voltage: DC12V (normal working voltage DC10V-16V)
Source: DC4V~20V (usual power supply positive trigger, button, PNP sensor, PLC signal, etc.)
Output capability: It can control devices within 30v5A or within 220v5A
Quiescent current: 20mA, working current: 50mA
Service life: more than 100,000 times;
Working temperature: -40~85 °C;
Net weight: about 26g
Size: 64.2mm*34.8mm*18.5mm
Working voltage: DC12V (normal working voltage DC10V-16V)
Source: DC4V~20V (usual power supply positive trigger, button, PNP sensor, PLC signal, etc.)
Output capability: It can control devices within 30v5A or within 220v5A
Quiescent current: 20mA, working current: 50mA
Service life: more than 100,000 times;
Working temperature: -40~85 °C;
Net weight: about 26g
Size: 64.2mm*34.8mm*18.5mm
Features
Voltage input anti-reverse circuit, worry-free wiring. Signal input optocoupler isolation, strong anti-interference ability. Set the parameter to power off permanent memory. Powerful flash MCU online programming function, according to user needs can contact the manufacturer to customize the required functions.
Voltage input anti-reverse circuit, worry-free wiring. Signal input optocoupler isolation, strong anti-interference ability. Set the parameter to power off permanent memory. Powerful flash MCU online programming function, according to user needs can contact the manufacturer to customize the required functions.
Wiring diagram
Function introduction
P-1: The signal triggers the relay to pull in. When the time is up, the relay is disconnected during the delay.
A: Invalid trigger again B: Re-trigger re-clocking C: Trigger relay reset again to stop timing
P-2: The signal trigger start timing time T1, the time is up to the relay pull-in time T2 is disconnected (reset)
A: Invalid trigger again B: Re-trigger re-clocking C: Start delay without triggering power-on
P-3: Cycling: Turn on T1, disconnect T2, infinite loop. For T1 and T2, the time is adjustable; if a parameter is turned ON or OFF, it can be turned on or the power is turned on.
A: The relay is turned on immediately after power-on. B: The relay is turned off and then turned on after power-on.
P-4: There is signal, the relay is closed, the suction is kept, the signal disappears, the timing starts, the time is up, the relay is disconnected, during the delay, the signal is given again, the delay is cancelled, the relay is kept, the signal disappears, and the time is re-timed.
P-1: The signal triggers the relay to pull in. When the time is up, the relay is disconnected during the delay.
A: Invalid trigger again B: Re-trigger re-clocking C: Trigger relay reset again to stop timing
P-2: The signal trigger start timing time T1, the time is up to the relay pull-in time T2 is disconnected (reset)
A: Invalid trigger again B: Re-trigger re-clocking C: Start delay without triggering power-on
P-3: Cycling: Turn on T1, disconnect T2, infinite loop. For T1 and T2, the time is adjustable; if a parameter is turned ON or OFF, it can be turned on or the power is turned on.
A: The relay is turned on immediately after power-on. B: The relay is turned off and then turned on after power-on.
P-4: There is signal, the relay is closed, the suction is kept, the signal disappears, the timing starts, the time is up, the relay is disconnected, during the delay, the signal is given again, the delay is cancelled, the relay is kept, the signal disappears, and the time is re-timed.
Notes
The relay output is a passive contact that has no live output and controls the on/off of a line.
The relay output is a passive contact that has no live output and controls the on/off of a line.
3.Digital Display Delay Controller:(DC 12V with Buzzer 3 Button)
Product parameters
Working voltage: DC12V (normal working voltage DC10V-16V)
Source: DC4V~20V (usual power supply positive trigger, button, PNP sensor, PLC signal, etc.)
Output capability: It can control devices within 30v5A or within 220v5A
Quiescent current: 20mA, working current: 50mA
Service life: more than 100,000 times;
Working temperature: -40~85 °C;
Net weight: about 26g
Size: 64.2mm*34.8mm*18.5mm
Features
Power input flash-coupled, strong-interference ability. Power of flash MCU online programming function, according to user needs can contact the manufacturer to customize the Required functions.
Working voltage: DC12V (normal working voltage DC10V-16V)
Source: DC4V~20V (usual power supply positive trigger, button, PNP sensor, PLC signal, etc.)
Output capability: It can control devices within 30v5A or within 220v5A
Quiescent current: 20mA, working current: 50mA
Service life: more than 100,000 times;
Working temperature: -40~85 °C;
Net weight: about 26g
Size: 64.2mm*34.8mm*18.5mm
Features
Power input flash-coupled, strong-interference ability. Power of flash MCU online programming function, according to user needs can contact the manufacturer to customize the Required functions.
Function introduction
P-1: The trigger signal is received, the relay is turned on, the timer expires, and the relay is turned off.
A1: Invalid again during delayed trigger
A2: Trigger again during retiming delay
A3: During the delay trigger, the trigger signal is received again to terminate the current delay.
P-2: Receive trigger signal, X start time, relay off, Y start time, relay open
P-3: Cycle switching mode
A1: After the power relay is turned on, the timing is turned off and the loop is infinite.
A2: After the power relay is turned off, the timing ends and the loop is infinite.
P-1: The trigger signal is received, the relay is turned on, the timer expires, and the relay is turned off.
A1: Invalid again during delayed trigger
A2: Trigger again during retiming delay
A3: During the delay trigger, the trigger signal is received again to terminate the current delay.
P-2: Receive trigger signal, X start time, relay off, Y start time, relay open
P-3: Cycle switching mode
A1: After the power relay is turned on, the timing is turned off and the loop is infinite.
A2: After the power relay is turned off, the timing ends and the loop is infinite.
Notes:
The relay output is a passive contact that has no live output and controls the on/off of a line.
The relay output is a passive contact that has no live output and controls the on/off of a line.
4.Dual MOS delay control board: (DC 5-30V 4 Button)
Description:
Dual MOS parallel active output, lower internal resistance, larger current, strong power interface, clear and simple, powerful, one-button emergency stop function (STOP button), with reverse connection protection, reverse connection, no burning, power-off memory. Increase Sleep mode, after enabling, no operation within 5 minutes, automatically turn off the display, wake up any button! You can set different OP, CL, LOP parameters, these parameters are independent of each other, save the setting parameters automatically power-down save and other functions, Almost all the needs!
Product manual
Working voltage: DC5V-DC30V (wide voltage anti-connection protection)
Trigger signal source: high-level trigger DC 3.0V—24V signal ground and system ground to improve the system's anti-interference ability can also short-circuit the ground
Output capacity: DC DC 5V--36V, continuous current 15A at normal temperature, power 400W! Under the condition of auxiliary heat dissipation, the maximum current can reach 30A
Product size: 64mm*35mm*19.3mm
Mounting hole: diameter 3mm
Working temperature: -40 ° C ~ 85 ° C
Working voltage: DC5V-DC30V (wide voltage anti-connection protection)
Trigger signal source: high-level trigger DC 3.0V—24V signal ground and system ground to improve the system's anti-interference ability can also short-circuit the ground
Output capacity: DC DC 5V--36V, continuous current 15A at normal temperature, power 400W! Under the condition of auxiliary heat dissipation, the maximum current can reach 30A
Product size: 64mm*35mm*19.3mm
Mounting hole: diameter 3mm
Working temperature: -40 ° C ~ 85 ° C
Operating mode
P1 mode: After the signal is triggered, the MOS transistor turns on the OP time and then turns off; in the OP time, the following operation
P1.1: The signal is triggered again.
P1.2: Signal triggers re-timed again
P1.3: The signal triggers reset again, the MOS tube is disconnected, and the timing is stopped.
P-2: Give the trigger signal, after the MOS transistor is disconnected from the CL time, the MOS transistor turns on the OP time. After the timing is completed, the MOS transistor is disconnected.
P3.1: Give the trigger signal, after the MOS transistor turns on the OP time, the MOS tube turns off the CL time, then loops the above action, the signal is given again in the loop, the MOS tube is disconnected, the timing is stopped; the number of cycles (LOP) can be set.
P3.2: No need to trigger signal after power-on, MOS tube turns on OP time, MOS tube disconnects CL time, loops the above action; loop number (LOP) can be set
P-4: Signal hold function If there is a trigger signal, the timing is cleared, the MOS transistor remains on; when the signal disappears, the MOS transistor is disconnected after timing the OP; during the timing, there is a signal and the timing is cleared.
P1 mode: After the signal is triggered, the MOS transistor turns on the OP time and then turns off; in the OP time, the following operation
P1.1: The signal is triggered again.
P1.2: Signal triggers re-timed again
P1.3: The signal triggers reset again, the MOS tube is disconnected, and the timing is stopped.
P-2: Give the trigger signal, after the MOS transistor is disconnected from the CL time, the MOS transistor turns on the OP time. After the timing is completed, the MOS transistor is disconnected.
P3.1: Give the trigger signal, after the MOS transistor turns on the OP time, the MOS tube turns off the CL time, then loops the above action, the signal is given again in the loop, the MOS tube is disconnected, the timing is stopped; the number of cycles (LOP) can be set.
P3.2: No need to trigger signal after power-on, MOS tube turns on OP time, MOS tube disconnects CL time, loops the above action; loop number (LOP) can be set
P-4: Signal hold function If there is a trigger signal, the timing is cleared, the MOS transistor remains on; when the signal disappears, the MOS transistor is disconnected after timing the OP; during the timing, there is a signal and the timing is cleared.
Relay enable mode
ON : MOS tube is allowed to conduct during OP conduction time
OFF : MOS tube is disabled, always off
Short press the STOP button on the main interface to switch between ON and OFF. The current state will flash, then return to the main interface. This function is the emergency stop function. One button is used to open and close the MOS tube.
ON : MOS tube is allowed to conduct during OP conduction time
OFF : MOS tube is disabled, always off
Short press the STOP button on the main interface to switch between ON and OFF. The current state will flash, then return to the main interface. This function is the emergency stop function. One button is used to open and close the MOS tube.
Sleep mode (long press the stop button to view the current mode)
C-P sleep mode: within five minutes, without any operation, the digital tube automatically turns off the display, the program runs normally.
O-d normal mode: the digital tube is always on display
Press and hold the STOP button for 2 seconds and then release to switch the C-P and O-d states. The current state will flash and then return to the main interface.
C-P sleep mode: within five minutes, without any operation, the digital tube automatically turns off the display, the program runs normally.
O-d normal mode: the digital tube is always on display
Press and hold the STOP button for 2 seconds and then release to switch the C-P and O-d states. The current state will flash and then return to the main interface.
Timing range
How to choose the timing range
1).After setting the parameter value in the mode selection interface, press the STOP button to select the timing range.
XXX. Decimal point is in one place, timing range: 1 second to 999 seconds
XX.X decimal point in ten, timing range: 0.1 seconds to 99.9 seconds
X.X.X. The decimal point is fully illuminated, the timing range is from 1 minute to 999 minutes.
How to choose the timing range
1).After setting the parameter value in the mode selection interface, press the STOP button to select the timing range.
XXX. Decimal point is in one place, timing range: 1 second to 999 seconds
XX.X decimal point in ten, timing range: 0.1 seconds to 99.9 seconds
X.X.X. The decimal point is fully illuminated, the timing range is from 1 minute to 999 minutes.
2).For example, if you want to set the OP to 3.2 seconds, move the decimal point to ten digits, and the digital tube displays 03.2.
Parameter description: OP on time, CL off time, LOP cycle number 1-999 times, "---" stands for infinite loop.
These parameters are independent of each other, but each mode shares these parameters. For example, when the on-time OP is set to 5 seconds in P1.1, the user wants to switch to the P1.2 mode, then when entering the P1.2 setting corresponding parameters, the OP also It will be 5 seconds.
Displaying 000 on the main interface and pressing the SET button will display OPL, LOP and corresponding time XXX
If only OP in the mode, such as mode P1.1, P1.2, P1.3 time, then short press SET button will only display OP and corresponding time.
If the mode has OP, CL, LOP such as mode P3.1, P3.2 short press SET button will display OP and corresponding time, CL and corresponding time, LOP and corresponding times.
After setting the mode, it is very convenient to easily check the parameters set in the current mode by pressing the SET button on the main interface.
Parameter description: OP on time, CL off time, LOP cycle number 1-999 times, "---" stands for infinite loop.
These parameters are independent of each other, but each mode shares these parameters. For example, when the on-time OP is set to 5 seconds in P1.1, the user wants to switch to the P1.2 mode, then when entering the P1.2 setting corresponding parameters, the OP also It will be 5 seconds.
Displaying 000 on the main interface and pressing the SET button will display OPL, LOP and corresponding time XXX
If only OP in the mode, such as mode P1.1, P1.2, P1.3 time, then short press SET button will only display OP and corresponding time.
If the mode has OP, CL, LOP such as mode P3.1, P3.2 short press SET button will display OP and corresponding time, CL and corresponding time, LOP and corresponding times.
After setting the mode, it is very convenient to easily check the parameters set in the current mode by pressing the SET button on the main interface.
How to set parameters
1) First determine the working mode of the MOS tube
According to the working mode of the MOS tube, in the main interface (when the module is powered on, it will flash the current working mode (default P1.1 mode), then enter the main interface "press and hold the SET button for 2 seconds and then release" to enter the mode. Select the interface, press the UP, DOWN button to select the mode to be set P1.1~P-4
2) After selecting the mode to be set (for example, P3.2), press the SET button to set the corresponding parameter. At this time, the parameter to be set will flash OP ON time, CL OFF time, LOP cycle number “---” Represents an infinite loop, adjusts the parameter value through UP and DOWN, supports long press (rapid increase or decrease) and short press (increase or decrease 1 unit); after setting the parameter value, select the decimal point position by short pressing the STOP button. , select the timing range (corresponding time 0.1 seconds ~ 999 minutes); short press the SET button to set the next parameter of the current mode, the process is the same as above.
3) After setting the parameters of the selected mode, press and hold the SET button for 2 seconds to release, the currently set mode will flash, then return to the main interface and set the parameters successfully.
4) Main interface: “000” (no decimal point) is displayed when the MOS tube is not working, and the MOS tube has a decimal point in the working state.
5) Mode selection interface: long press SET button to enter, after setting is completed, long press SET button to exit, return to the main interface
1) First determine the working mode of the MOS tube
According to the working mode of the MOS tube, in the main interface (when the module is powered on, it will flash the current working mode (default P1.1 mode), then enter the main interface "press and hold the SET button for 2 seconds and then release" to enter the mode. Select the interface, press the UP, DOWN button to select the mode to be set P1.1~P-4
2) After selecting the mode to be set (for example, P3.2), press the SET button to set the corresponding parameter. At this time, the parameter to be set will flash OP ON time, CL OFF time, LOP cycle number “---” Represents an infinite loop, adjusts the parameter value through UP and DOWN, supports long press (rapid increase or decrease) and short press (increase or decrease 1 unit); after setting the parameter value, select the decimal point position by short pressing the STOP button. , select the timing range (corresponding time 0.1 seconds ~ 999 minutes); short press the SET button to set the next parameter of the current mode, the process is the same as above.
3) After setting the parameters of the selected mode, press and hold the SET button for 2 seconds to release, the currently set mode will flash, then return to the main interface and set the parameters successfully.
4) Main interface: “000” (no decimal point) is displayed when the MOS tube is not working, and the MOS tube has a decimal point in the working state.
5) Mode selection interface: long press SET button to enter, after setting is completed, long press SET button to exit, return to the main interface
Note:
The module is an active live output, and the voltage at the output (load) is equal to the input voltage DC
The module is an active live output, and the voltage at the output (load) is equal to the input voltage DC
5.USD Digital Display Delay Controller: ( DC12V 4 Button )
Description:
This relay delay control board has a powerful and clear interface, powerful function, one-button emergency stop function (STOP button), with reverse connection protection, reverse connection without burning, power-off memory. Increased sleep mode, after enabling, No operation within 5 minutes, automatically turn off the display, wake up any button! You can set different OP, CL, LOP parameters, these parameters are independent of each other, save the setting parameters automatically power-down save and other functions, almost meet all needs!
Product manual:
Working voltage: DC6V-DC30V (wide voltage anti-connection protection)
Trigger signal source: high-level trigger DC 3.0V—24V signal ground and system ground to improve the system's anti-interference ability can also short-circuit the ground
Output capacity: controllable DC 30V/10A or AC 250V/10A equipment
Product size: 64mm*35mm*19.3mm
Mounting hole: diameter 3mm
Working temperature: -40 ° C ~ 85 ° C
Working voltage: DC6V-DC30V (wide voltage anti-connection protection)
Trigger signal source: high-level trigger DC 3.0V—24V signal ground and system ground to improve the system's anti-interference ability can also short-circuit the ground
Output capacity: controllable DC 30V/10A or AC 250V/10A equipment
Product size: 64mm*35mm*19.3mm
Mounting hole: diameter 3mm
Working temperature: -40 ° C ~ 85 ° C
6.DC Motor Speed Controller :(DC 8-55V Motor Speed Controller )
Description:
This product brings together a wide range of modern motor speed control, with the advantages of small size, simple operation, high current resistance and reverse connection. Suitable for most users in various environments with various speeds, support acceleration and deceleration functions can be set through the menu, with set parameters power off permanent memory function
Product manual:
Voltage: DC8V-55V (wide voltage anti-back protection)
Speed range: long press / short press to adjust the degree, 0% -100% speed
Drive current: up to 10A, (recommended output series 12A fuse)
Standby current: <17mA
Mounting hole: diameter 3mm
Product size: 64mm*35mm*19mm (length * width * height)
Working temperature: -20 ° C ~ 70 ° C
Instructions:
1. Click/long press the “speed increase” button to increase the motor speed to 100%.
2. Click/long press the “speed down” button to increase the motor speed to a minimum of 0%.
3. Press and hold the “Power On/Off” button for one second, the controller will be turned on or off (the power is turned off by default, and the memory function is activated after booting)
Voltage: DC8V-55V (wide voltage anti-back protection)
Speed range: long press / short press to adjust the degree, 0% -100% speed
Drive current: up to 10A, (recommended output series 12A fuse)
Standby current: <17mA
Mounting hole: diameter 3mm
Product size: 64mm*35mm*19mm (length * width * height)
Working temperature: -20 ° C ~ 70 ° C
Instructions:
1. Click/long press the “speed increase” button to increase the motor speed to 100%.
2. Click/long press the “speed down” button to increase the motor speed to a minimum of 0%.
3. Press and hold the “Power On/Off” button for one second, the controller will be turned on or off (the power is turned off by default, and the memory function is activated after booting)
Precautions:
1. The digital tube flashes at the moment of power-on (normal phenomenon, no need to worry)
2, close to the limit drive current working conditions, it is recommended to take the output end of the fuse
3. The DC motor speed controller cannot be installed in places where there is dripping water and children can reach it.
4. After wiring, check if the line is correct and then energize, so as to avoid accidentally burning the temperature controller and load device.
1. The digital tube flashes at the moment of power-on (normal phenomenon, no need to worry)
2, close to the limit drive current working conditions, it is recommended to take the output end of the fuse
3. The DC motor speed controller cannot be installed in places where there is dripping water and children can reach it.
4. After wiring, check if the line is correct and then energize, so as to avoid accidentally burning the temperature controller and load device.
Wiring:
“M+” and “M-” are respectively connected to the positive and negative terminals of the output, M+ is positive and M- is negative.
“VIN” and “GND” are respectively connected to the positive and negative terminals of the input terminal, Vin is positive and GND is negative (input power supply voltage is DC8V-55V)
“M+” and “M-” are respectively connected to the positive and negative terminals of the output, M+ is positive and M- is negative.
“VIN” and “GND” are respectively connected to the positive and negative terminals of the input terminal, Vin is positive and GND is negative (input power supply voltage is DC8V-55V)
7.Temperature Controller:(DC 12V Temperrature Controller)
Product Parameters:
Control range: -50~110°C
Resolution: -9.9~99.9, 0.1°C, other temperature range, 1°C
Temperature measurement accuracy: 0.1 °C
Control accuracy: 0.1 ° C
Hysteresis accuracy: 0.1 ° C
Refresh rate: 0.5S
High temperature alarm: 0-110 °C
Measurement input: NTC (10K0.5%) waterproof sensor
Output: One way 10A relay
Environmental requirements: Temperature -10~60°C Humidity 20%-85%
Size: 48*40mm
Power consumption of the whole machine: quiescent current: ≤35MA, Pull-in current: ≤65MA
Resolution: -9.9~99.9, 0.1°C, other temperature range, 1°C
Temperature measurement accuracy: 0.1 °C
Control accuracy: 0.1 ° C
Hysteresis accuracy: 0.1 ° C
Refresh rate: 0.5S
High temperature alarm: 0-110 °C
Measurement input: NTC (10K0.5%) waterproof sensor
Output: One way 10A relay
Environmental requirements: Temperature -10~60°C Humidity 20%-85%
Size: 48*40mm
Power consumption of the whole machine: quiescent current: ≤35MA, Pull-in current: ≤65MA
Setting Parameter Method:
Once the power supply and load are connected, the control can be powered. After power-on, the digital tube displays the current real-time temperature. Press the SET button briefly, the digital tube displays the temperature flashing, press the + - button to adjust the set temperature; after the adjustment is completed, press the SET button to save the set temperature and return. At this time, the controller automatically Execute the relay on and off; press and hold the SET button for 5 seconds to enter the menu parameter setting, short press the + - button to switch P0...P6, short press the SET button to enter the menu.
The thermostat output is a 10A relay to meet a variety of high power loads, please ensure that the line is correct.
Once the power supply and load are connected, the control can be powered. After power-on, the digital tube displays the current real-time temperature. Press the SET button briefly, the digital tube displays the temperature flashing, press the + - button to adjust the set temperature; after the adjustment is completed, press the SET button to save the set temperature and return. At this time, the controller automatically Execute the relay on and off; press and hold the SET button for 5 seconds to enter the menu parameter setting, short press the + - button to switch P0...P6, short press the SET button to enter the menu.
The thermostat output is a 10A relay to meet a variety of high power loads, please ensure that the line is correct.
Indicator light, digital tube status description:
Indicator light: Off means the relay is off, steady light means the relay is closed
Digital tube: Display LLL for sensor open circuit: Display HHH is out of measurement range. The thermostat will forcibly open the relay.
Indicator light: Off means the relay is off, steady light means the relay is closed
Digital tube: Display LLL for sensor open circuit: Display HHH is out of measurement range. The thermostat will forcibly open the relay.
Parameter Function Description:
Menu identifier | Menu function | Predetermined area | Factory setting |
P0 | Refrigeration C / Heating H | C/H | C |
P1 | Backlash | 0.1-15 | 2.0 |
P2 | Maximum set temperature | -50~110℃ | 110 |
P3 | Minimum set temperature | -50~110℃ | -50 |
P4 | Temperature correction | -7.0~7.0℃ | 0.0 |
P5 | Press delay | 0-10 minutes | 0 |
P6 | High temperature alarm | ON/OFF |
OFF
|
Package Included:
1PC*DC 12V 2/3/4 Button Time Delay Relay Motor Speed Temperrature Controller+Buzzer(According to your choice)
Purchasing & Delivery
Before you make your purchase, it’s helpful to know the measurements of the area you plan to place the furniture. You should also measure any doorways and hallways through which the furniture will pass to get to its final destination.Picking up at the store
Shopify Shop requires that all products are properly inspected BEFORE you take it home to insure there are no surprises. Our team is happy to open all packages and will assist in the inspection process. We will then reseal packages for safe transport. We encourage all customers to bring furniture pads or blankets to protect the items during transport as well as rope or tie downs. Shopify Shop will not be responsible for damage that occurs after leaving the store or during transit. It is the purchaser’s responsibility to make sure the correct items are picked up and in good condition.Delivery
Customers are able to pick the next available delivery day that best fits their schedule. However, to route stops as efficiently as possible, Shopify Shop will provide the time frame. Customers will not be able to choose a time. You will be notified in advance of your scheduled time frame. Please make sure that a responsible adult (18 years or older) will be home at that time.In preparation for your delivery, please remove existing furniture, pictures, mirrors, accessories, etc. to prevent damages. Also insure that the area where you would like your furniture placed is clear of any old furniture and any other items that may obstruct the passageway of the delivery team. Shopify Shop will deliver, assemble, and set-up your new furniture purchase and remove all packing materials from your home. Our delivery crews are not permitted to move your existing furniture or other household items. Delivery personnel will attempt to deliver the purchased items in a safe and controlled manner but will not attempt to place furniture if they feel it will result in damage to the product or your home. Delivery personnel are unable to remove doors, hoist furniture or carry furniture up more than 3 flights of stairs. An elevator must be available for deliveries to the 4th floor and above.
Other Customers also buy:
-
Translation missing: en.products.product.regular_price $5.99{"id":6086411911368,"title":"5V\/12V 2\/3\/4 Button Timer Delay Relay Motor Speed Temperature Controller+Buzzer","handle":"5v-12v-2-3-4-button-timer-delay-relay-motor-speed-temperature-controller-buzzer","description":"\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e1.Digital Display Delay Controller:(DC 12V with Buzzer 2 Button\u003cspan face=\"helveticao\" data-mce-fragment=\"1\"\u003e)\u003c\/span\u003e\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eProduct parameters\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\n\u003cul data-mce-fragment=\"1\"\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eWorking voltage: DC12V (normal working voltage DC10V-16V)\u003c\/span\u003e\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eSignal source: DC4V~20V (usual power supply positive trigger, button, PNP sensor, PLC signal, etc.)\u003c\/span\u003e\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eOutput capability: It can control devices within 30v5A or within 220v5A\u003c\/span\u003e\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eQuiescent current: 20mA, working current: 50mA\u003c\/span\u003e\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eService life: more than 100,000 times;\u003c\/span\u003e\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eWorking temperature: -40~85 °C;\u003c\/span\u003e\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eNet weight: about 26g\u003c\/span\u003e\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eSize: 64.2mm*34.8mm*18.5mm\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eFeatures\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\n\u003cul data-mce-fragment=\"1\"\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eVoltage input anti-reverse circuit, worry-free wiring. Signal input optocoupler isolation, strong anti-interference ability. Set the parameter to power off permanent memory. Powerful flash MCU online programming function, according to user needs can contact the manufacturer to customize the required functions.\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eFunction introduction\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\n\u003cul data-mce-fragment=\"1\"\u003e\n\u003cli data-mce-fragment=\"1\"\u003eWhen the power is turned on, the trigger signal is received, the countdown starts, and the relay works. When the timer ends, the relay stops working, the time returns to the setting, and the next trigger signal is waited.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eInstructions\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cul data-mce-fragment=\"1\"\u003e\n\u003cli data-mce-fragment=\"1\"\u003e1).Press K1 to enter the time setting, the hundred digit digital tube starts to flash; press K2 at this time, the hundred digits change; press K1 again, the ten digital tube starts to flash; press K2 at this time, the ten digits change; press again After K1, the digital tube starts to flash. At this time, press K2, the digit of the digit changes; press K1 again to exit the setting, and the digital tube no longer flashes.\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003e2).When the digital tube is normally displayed, press K2, the decimal point is shifted, the decimal point is 0 to 999 seconds in ones digit, the decimal point is 0 to 99.9 seconds in ten digits, and the decimal point is 0 to 999 minutes; the time is set.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e2.Digital Display Delay Controller:(DC 12V 3 Button)\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eProduct parameters\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eWorking voltage: DC12V (normal working voltage DC10V-16V)\u003cbr data-mce-fragment=\"1\"\u003eSource: DC4V~20V (usual power supply positive trigger, button, PNP sensor, PLC signal, etc.)\u003cbr data-mce-fragment=\"1\"\u003eOutput capability: It can control devices within 30v5A or within 220v5A\u003cbr data-mce-fragment=\"1\"\u003eQuiescent current: 20mA, working current: 50mA\u003cbr data-mce-fragment=\"1\"\u003eService life: more than 100,000 times;\u003cbr data-mce-fragment=\"1\"\u003eWorking temperature: -40~85 °C;\u003cbr data-mce-fragment=\"1\"\u003eNet weight: about 26g\u003cbr data-mce-fragment=\"1\"\u003eSize: 64.2mm*34.8mm*18.5mm\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eFeatures\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eVoltage input anti-reverse circuit, worry-free wiring. Signal input optocoupler isolation, strong anti-interference ability. Set the parameter to power off permanent memory. Powerful flash MCU online programming function, according to user needs can contact the manufacturer to customize the required functions.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eWiring diagram\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cimg src=\"https:\/\/pg-cdn-a2.datacaciques.com\/00\/NDAy\/19\/08\/21\/02s76nl1201bce4t\/76050b0dfcc5297c.jpg\" data-mce-fragment=\"1\" data-mce-src=\"https:\/\/pg-cdn-a2.datacaciques.com\/00\/NDAy\/19\/08\/21\/02s76nl1201bce4t\/76050b0dfcc5297c.jpg\"\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eFunction introduction\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eP-1: The signal triggers the relay to pull in. When the time is up, the relay is disconnected during the delay.\u003cbr data-mce-fragment=\"1\"\u003eA: Invalid trigger again B: Re-trigger re-clocking C: Trigger relay reset again to stop timing\u003cbr data-mce-fragment=\"1\"\u003eP-2: The signal trigger start timing time T1, the time is up to the relay pull-in time T2 is disconnected (reset)\u003cbr data-mce-fragment=\"1\"\u003eA: Invalid trigger again B: Re-trigger re-clocking C: Start delay without triggering power-on\u003cbr data-mce-fragment=\"1\"\u003eP-3: Cycling: Turn on T1, disconnect T2, infinite loop. For T1 and T2, the time is adjustable; if a parameter is turned ON or OFF, it can be turned on or the power is turned on.\u003cbr data-mce-fragment=\"1\"\u003eA: The relay is turned on immediately after power-on. B: The relay is turned off and then turned on after power-on.\u003cbr data-mce-fragment=\"1\"\u003eP-4: There is signal, the relay is closed, the suction is kept, the signal disappears, the timing starts, the time is up, the relay is disconnected, during the delay, the signal is given again, the delay is cancelled, the relay is kept, the signal disappears, and the time is re-timed.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cstrong data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eNotes\u003c\/span\u003e\u003c\/strong\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eThe relay output is a passive contact that has no live output and controls the on\/off of a line.\u003c\/span\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e\u003cspan face=\"helveticao\" data-mce-fragment=\"1\"\u003e3.Digital Display Delay Controller:(DC 12V with Buzzer 3 Button)\u003c\/span\u003e\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan face=\"helveticao\" data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eProduct parameters\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eWorking voltage: DC12V (normal working voltage DC10V-16V)\u003cbr data-mce-fragment=\"1\"\u003eSource: DC4V~20V (usual power supply positive trigger, button, PNP sensor, PLC signal, etc.)\u003cbr data-mce-fragment=\"1\"\u003eOutput capability: It can control devices within 30v5A or within 220v5A\u003cbr data-mce-fragment=\"1\"\u003eQuiescent current: 20mA, working current: 50mA\u003cbr data-mce-fragment=\"1\"\u003eService life: more than 100,000 times;\u003cbr data-mce-fragment=\"1\"\u003eWorking temperature: -40~85 °C;\u003cbr data-mce-fragment=\"1\"\u003eNet weight: about 26g\u003cbr data-mce-fragment=\"1\"\u003eSize: 64.2mm*34.8mm*18.5mm\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eFeatures\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003ePower input flash-coupled, strong-interference ability. Power of flash MCU online programming function, according to user needs can contact the manufacturer to customize the Required functions.\u003c\/span\u003e\u003cspan face=\"helveticao\" data-mce-fragment=\"1\"\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003c\/span\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003eFunction introduction\u003cbr data-mce-fragment=\"1\"\u003eP-1: The trigger signal is received, the relay is turned on, the timer expires, and the relay is turned off.\u003cbr data-mce-fragment=\"1\"\u003eA1: Invalid again during delayed trigger\u003cbr data-mce-fragment=\"1\"\u003eA2: Trigger again during retiming delay\u003cbr data-mce-fragment=\"1\"\u003eA3: During the delay trigger, the trigger signal is received again to terminate the current delay.\u003cbr data-mce-fragment=\"1\"\u003eP-2: Receive trigger signal, X start time, relay off, Y start time, relay open\u003cbr data-mce-fragment=\"1\"\u003eP-3: Cycle switching mode\u003cbr data-mce-fragment=\"1\"\u003eA1: After the power relay is turned on, the timing is turned off and the loop is infinite.\u003cbr data-mce-fragment=\"1\"\u003eA2: After the power relay is turned off, the timing ends and the loop is infinite.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cstrong data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eNotes:\u003c\/span\u003e\u003c\/strong\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eThe relay output is a passive contact that has no live output and controls the on\/off of a line.\u003c\/span\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e4.Dual MOS delay control board: (DC 5-30V 4 Button)\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eDescription:\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003eDual MOS parallel active output, lower internal resistance, larger current, strong power interface, clear and simple, powerful, one-button emergency stop function (STOP button), with reverse connection protection, reverse connection, no burning, power-off memory. Increase Sleep mode, after enabling, no operation within 5 minutes, automatically turn off the display, wake up any button! You can set different OP, CL, LOP parameters, these parameters are independent of each other, save the setting parameters automatically power-down save and other functions, Almost all the needs!\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eProduct manual\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eWorking voltage: DC5V-DC30V (wide voltage anti-connection protection)\u003cbr data-mce-fragment=\"1\"\u003eTrigger signal source: high-level trigger DC 3.0V—24V signal ground and system ground to improve the system's anti-interference ability can also short-circuit the ground\u003cbr data-mce-fragment=\"1\"\u003eOutput capacity: DC DC 5V--36V, continuous current 15A at normal temperature, power 400W! Under the condition of auxiliary heat dissipation, the maximum current can reach 30A\u003cbr data-mce-fragment=\"1\"\u003eProduct size: 64mm*35mm*19.3mm\u003cbr data-mce-fragment=\"1\"\u003eMounting hole: diameter 3mm\u003cbr data-mce-fragment=\"1\"\u003eWorking temperature: -40 ° C ~ 85 ° C\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eOperating mode\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eP1 mode: After the signal is triggered, the MOS transistor turns on the OP time and then turns off; in the OP time, the following operation\u003cbr data-mce-fragment=\"1\"\u003eP1.1: The signal is triggered again.\u003cbr data-mce-fragment=\"1\"\u003eP1.2: Signal triggers re-timed again\u003cbr data-mce-fragment=\"1\"\u003eP1.3: The signal triggers reset again, the MOS tube is disconnected, and the timing is stopped.\u003cbr data-mce-fragment=\"1\"\u003eP-2: Give the trigger signal, after the MOS transistor is disconnected from the CL time, the MOS transistor turns on the OP time. After the timing is completed, the MOS transistor is disconnected.\u003cbr data-mce-fragment=\"1\"\u003eP3.1: Give the trigger signal, after the MOS transistor turns on the OP time, the MOS tube turns off the CL time, then loops the above action, the signal is given again in the loop, the MOS tube is disconnected, the timing is stopped; the number of cycles (LOP) can be set.\u003cbr data-mce-fragment=\"1\"\u003eP3.2: No need to trigger signal after power-on, MOS tube turns on OP time, MOS tube disconnects CL time, loops the above action; loop number (LOP) can be set\u003cbr data-mce-fragment=\"1\"\u003eP-4: Signal hold function If there is a trigger signal, the timing is cleared, the MOS transistor remains on; when the signal disappears, the MOS transistor is disconnected after timing the OP; during the timing, there is a signal and the timing is cleared.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eRelay enable mode\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eON : MOS tube is allowed to conduct during OP conduction time\u003cbr data-mce-fragment=\"1\"\u003eOFF : MOS tube is disabled, always off\u003cbr data-mce-fragment=\"1\"\u003eShort press the STOP button on the main interface to switch between ON and OFF. The current state will flash, then return to the main interface. This function is the emergency stop function. One button is used to open and close the MOS tube.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eSleep mode (long press the stop button to view the current mode)\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eC-P sleep mode: within five minutes, without any operation, the digital tube automatically turns off the display, the program runs normally.\u003cbr data-mce-fragment=\"1\"\u003eO-d normal mode: the digital tube is always on display\u003cbr data-mce-fragment=\"1\"\u003ePress and hold the STOP button for 2 seconds and then release to switch the C-P and O-d states. The current state will flash and then return to the main interface.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eTiming range\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eHow to choose the timing range\u003cbr data-mce-fragment=\"1\"\u003e1).After setting the parameter value in the mode selection interface, press the STOP button to select the timing range.\u003cbr data-mce-fragment=\"1\"\u003eXXX. Decimal point is in one place, timing range: 1 second to 999 seconds\u003cbr data-mce-fragment=\"1\"\u003eXX.X decimal point in ten, timing range: 0.1 seconds to 99.9 seconds\u003cbr data-mce-fragment=\"1\"\u003eX.X.X. The decimal point is fully illuminated, the timing range is from 1 minute to 999 minutes.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e2).For example, if you want to set the OP to 3.2 seconds, move the decimal point to ten digits, and the digital tube displays 03.2.\u003cbr data-mce-fragment=\"1\"\u003eParameter description: OP on time, CL off time, LOP cycle number 1-999 times, \"---\" stands for infinite loop.\u003cbr data-mce-fragment=\"1\"\u003eThese parameters are independent of each other, but each mode shares these parameters. For example, when the on-time OP is set to 5 seconds in P1.1, the user wants to switch to the P1.2 mode, then when entering the P1.2 setting corresponding parameters, the OP also It will be 5 seconds.\u003cbr data-mce-fragment=\"1\"\u003eDisplaying 000 on the main interface and pressing the SET button will display OPL, LOP and corresponding time XXX\u003cbr data-mce-fragment=\"1\"\u003eIf only OP in the mode, such as mode P1.1, P1.2, P1.3 time, then short press SET button will only display OP and corresponding time.\u003cbr data-mce-fragment=\"1\"\u003eIf the mode has OP, CL, LOP such as mode P3.1, P3.2 short press SET button will display OP and corresponding time, CL and corresponding time, LOP and corresponding times.\u003cbr data-mce-fragment=\"1\"\u003eAfter setting the mode, it is very convenient to easily check the parameters set in the current mode by pressing the SET button on the main interface.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eHow to set parameters\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e1) First determine the working mode of the MOS tube\u003cbr data-mce-fragment=\"1\"\u003eAccording to the working mode of the MOS tube, in the main interface (when the module is powered on, it will flash the current working mode (default P1.1 mode), then enter the main interface \"press and hold the SET button for 2 seconds and then release\" to enter the mode. Select the interface, press the UP, DOWN button to select the mode to be set P1.1~P-4\u003cbr data-mce-fragment=\"1\"\u003e2) After selecting the mode to be set (for example, P3.2), press the SET button to set the corresponding parameter. At this time, the parameter to be set will flash OP ON time, CL OFF time, LOP cycle number “---” Represents an infinite loop, adjusts the parameter value through UP and DOWN, supports long press (rapid increase or decrease) and short press (increase or decrease 1 unit); after setting the parameter value, select the decimal point position by short pressing the STOP button. , select the timing range (corresponding time 0.1 seconds ~ 999 minutes); short press the SET button to set the next parameter of the current mode, the process is the same as above.\u003cbr data-mce-fragment=\"1\"\u003e3) After setting the parameters of the selected mode, press and hold the SET button for 2 seconds to release, the currently set mode will flash, then return to the main interface and set the parameters successfully.\u003cbr data-mce-fragment=\"1\"\u003e4) Main interface: “000” (no decimal point) is displayed when the MOS tube is not working, and the MOS tube has a decimal point in the working state.\u003cbr data-mce-fragment=\"1\"\u003e5) Mode selection interface: long press SET button to enter, after setting is completed, long press SET button to exit, return to the main interface\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cstrong data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eNote:\u003c\/span\u003e\u003c\/strong\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eThe module is an active live output, and the voltage at the output (load) is equal to the input voltage DC\u003c\/span\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e5.USD Digital Display Delay Controller: ( DC12V 4 Button )\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eDescription:\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003eThis relay delay control board has a powerful and clear interface, powerful function, one-button emergency stop function (STOP button), with reverse connection protection, reverse connection without burning, power-off memory. Increased sleep mode, after enabling, No operation within 5 minutes, automatically turn off the display, wake up any button! You can set different OP, CL, LOP parameters, these parameters are independent of each other, save the setting parameters automatically power-down save and other functions, almost meet all needs!\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eProduct manual:\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eWorking voltage: DC6V-DC30V (wide voltage anti-connection protection)\u003cbr data-mce-fragment=\"1\"\u003eTrigger signal source: high-level trigger DC 3.0V—24V signal ground and system ground to improve the system's anti-interference ability can also short-circuit the ground\u003cbr data-mce-fragment=\"1\"\u003eOutput capacity: controllable DC 30V\/10A or AC 250V\/10A equipment\u003cbr data-mce-fragment=\"1\"\u003eProduct size: 64mm*35mm*19.3mm\u003cbr data-mce-fragment=\"1\"\u003eMounting hole: diameter 3mm\u003cbr data-mce-fragment=\"1\"\u003eWorking temperature: -40 ° C ~ 85 ° C\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e6.DC Motor Speed Controller :(DC 8-55V Motor Speed Controller )\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eDescription:\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003eThis product brings together a wide range of modern motor speed control, with the advantages of small size, simple operation, high current resistance and reverse connection. Suitable for most users in various environments with various speeds, support acceleration and deceleration functions can be set through the menu, with set parameters power off permanent memory function\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eProduct manual:\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eVoltage: DC8V-55V (wide voltage anti-back protection)\u003cbr data-mce-fragment=\"1\"\u003eSpeed range: long press \/ short press to adjust the degree, 0% -100% speed\u003cbr data-mce-fragment=\"1\"\u003eDrive current: up to 10A, (recommended output series 12A fuse)\u003cbr data-mce-fragment=\"1\"\u003eStandby current: \u0026lt;17mA\u003cbr data-mce-fragment=\"1\"\u003eMounting hole: diameter 3mm\u003cbr data-mce-fragment=\"1\"\u003eProduct size: 64mm*35mm*19mm (length * width * height)\u003cbr data-mce-fragment=\"1\"\u003eWorking temperature: -20 ° C ~ 70 ° C\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eInstructions:\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e1. Click\/long press the “speed increase” button to increase the motor speed to 100%.\u003cbr data-mce-fragment=\"1\"\u003e2. Click\/long press the “speed down” button to increase the motor speed to a minimum of 0%.\u003cbr data-mce-fragment=\"1\"\u003e3. Press and hold the “Power On\/Off” button for one second, the controller will be turned on or off (the power is turned off by default, and the memory function is activated after booting)\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003ePrecautions:\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e1. The digital tube flashes at the moment of power-on (normal phenomenon, no need to worry)\u003cbr data-mce-fragment=\"1\"\u003e2, close to the limit drive current working conditions, it is recommended to take the output end of the fuse\u003cbr data-mce-fragment=\"1\"\u003e3. The DC motor speed controller cannot be installed in places where there is dripping water and children can reach it.\u003cbr data-mce-fragment=\"1\"\u003e4. After wiring, check if the line is correct and then energize, so as to avoid accidentally burning the temperature controller and load device.\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003eWiring:\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e“M+” and “M-” are respectively connected to the positive and negative terminals of the output, M+ is positive and M- is negative.\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e“VIN” and “GND” are respectively connected to the positive and negative terminals of the input terminal, Vin is positive and GND is negative (input power supply voltage is DC8V-55V)\u003c\/span\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e7.Temperature Controller:(DC 12V Temperrature Controller)\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eProduct Parameters:\u003c\/span\u003e\u003c\/strong\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003eControl range: -50~110°C\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eResolution: -9.9~99.9, 0.1°C, other temperature range, 1°C\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eTemperature measurement accuracy: 0.1 °C\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eControl accuracy: 0.1 ° C\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eHysteresis accuracy: 0.1 ° C\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eRefresh rate: 0.5S\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eHigh temperature alarm: 0-110 °C\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eMeasurement input: NTC (10K0.5%) waterproof sensor\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eOutput: One way 10A relay\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eEnvironmental requirements: Temperature -10~60°C Humidity 20%-85%\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eSize: 48*40mm\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003ePower consumption of the whole machine: quiescent current: ≤35MA, Pull-in current: ≤65MA\u003c\/span\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eSetting Parameter Method:\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eOnce the power supply and load are connected, the control can be powered. After power-on, the digital tube displays the current real-time temperature. Press the SET button briefly, the digital tube displays the temperature flashing, press the + - button to adjust the set temperature; after the adjustment is completed, press the SET button to save the set temperature and return. At this time, the controller automatically Execute the relay on and off; press and hold the SET button for 5 seconds to enter the menu parameter setting, short press the + - button to switch P0...P6, short press the SET button to enter the menu.\u003cbr data-mce-fragment=\"1\"\u003eThe thermostat output is a 10A relay to meet a variety of high power loads, please ensure that the line is correct.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eIndicator light, digital tube status description:\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eIndicator light: Off means the relay is off, steady light means the relay is closed\u003cbr data-mce-fragment=\"1\"\u003eDigital tube: Display LLL for sensor open circuit: Display HHH is out of measurement range. The thermostat will forcibly open the relay.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eParameter Function Description:\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003ctable data-mce-fragment=\"1\"\u003e\n\u003ctbody data-mce-fragment=\"1\"\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eMenu identifier\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eMenu function\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003ePredetermined area\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eFactory setting\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eP0\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eRefrigeration C \/ Heating H\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eC\/H\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eC\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eP1\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eBacklash\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e0.1-15\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e2.0\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eP2\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eMaximum set temperature\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e-50~110℃\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e110\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eP3\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eMinimum set temperature\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e-50~110℃\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e-50\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eP4\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eTemperature correction\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e-7.0~7.0℃\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e0.0\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eP5\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003ePress delay\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e0-10 minutes\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e0\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eP6\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eHigh temperature alarm\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eON\/OFF\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003eOFF\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003ePackage Included:\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e1PC*DC 12V 2\/3\/4 Button Time Delay Relay Motor Speed Temperrature Controller+Buzzer\u003cstrong data-mce-fragment=\"1\"\u003e(According to your choice)\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e","published_at":"2020-11-17T14:10:21+08:00","created_at":"2020-11-17T14:10:20+08:00","vendor":"DIYMORE","type":"","tags":[],"price":899,"price_min":899,"price_max":899,"available":true,"price_varies":false,"compare_at_price":null,"compare_at_price_min":0,"compare_at_price_max":0,"compare_at_price_varies":false,"variants":[{"id":37539263873224,"title":"DC 8-55V Motor Speed Controller","option1":"DC 8-55V Motor Speed Controller","option2":null,"option3":null,"sku":"100040","requires_shipping":true,"taxable":false,"featured_image":null,"available":true,"name":"5V\/12V 2\/3\/4 Button Timer Delay Relay Motor Speed Temperature Controller+Buzzer - DC 8-55V Motor Speed Controller","public_title":"DC 8-55V Motor Speed Controller","options":["DC 8-55V Motor Speed Controller"],"price":899,"weight":0,"compare_at_price":null,"inventory_management":"shopify","barcode":"","requires_selling_plan":false,"selling_plan_allocations":[]}],"images":["\/\/www.diymore.cc\/cdn\/shop\/products\/100040_1.jpg?v=1605593426","\/\/www.diymore.cc\/cdn\/shop\/products\/100040_2.jpg?v=1605593426","\/\/www.diymore.cc\/cdn\/shop\/products\/100040.jpg?v=1605593426","\/\/www.diymore.cc\/cdn\/shop\/products\/100040_8.jpg?v=1605593426","\/\/www.diymore.cc\/cdn\/shop\/products\/100040_867e837f-1764-4e74-953c-5a0322a10abe.jpg?v=1605593426","\/\/www.diymore.cc\/cdn\/shop\/products\/100040_7.jpg?v=1605593426","\/\/www.diymore.cc\/cdn\/shop\/products\/100040_4.jpg?v=1605593426","\/\/www.diymore.cc\/cdn\/shop\/products\/100040_5.jpg?v=1605593427","\/\/www.diymore.cc\/cdn\/shop\/products\/100040_6.jpg?v=1605593427","\/\/www.diymore.cc\/cdn\/shop\/products\/100040_3.jpg?v=1605593427"],"featured_image":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040_1.jpg?v=1605593426","options":["Size"],"media":[{"alt":null,"id":14960171581640,"position":1,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040_1.jpg?v=1605593426"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040_1.jpg?v=1605593426","width":1000},{"alt":null,"id":14960171614408,"position":2,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040_2.jpg?v=1605593426"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040_2.jpg?v=1605593426","width":1000},{"alt":null,"id":14960171647176,"position":3,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040.jpg?v=1605593426"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040.jpg?v=1605593426","width":1000},{"alt":null,"id":14960171679944,"position":4,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040_8.jpg?v=1605593426"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040_8.jpg?v=1605593426","width":1000},{"alt":null,"id":14960171712712,"position":5,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040_867e837f-1764-4e74-953c-5a0322a10abe.jpg?v=1605593426"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040_867e837f-1764-4e74-953c-5a0322a10abe.jpg?v=1605593426","width":1000},{"alt":null,"id":14960171745480,"position":6,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040_7.jpg?v=1605593426"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040_7.jpg?v=1605593426","width":1000},{"alt":null,"id":14960171778248,"position":7,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040_4.jpg?v=1605593426"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040_4.jpg?v=1605593426","width":1000},{"alt":null,"id":14960171811016,"position":8,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040_5.jpg?v=1605593427"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040_5.jpg?v=1605593427","width":1000},{"alt":null,"id":14960171843784,"position":9,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040_6.jpg?v=1605593427"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040_6.jpg?v=1605593427","width":1000},{"alt":null,"id":14960171876552,"position":10,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040_3.jpg?v=1605593427"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040_3.jpg?v=1605593427","width":1000}],"requires_selling_plan":false,"selling_plan_groups":[],"content":"\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e1.Digital Display Delay Controller:(DC 12V with Buzzer 2 Button\u003cspan face=\"helveticao\" data-mce-fragment=\"1\"\u003e)\u003c\/span\u003e\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eProduct parameters\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\n\u003cul data-mce-fragment=\"1\"\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eWorking voltage: DC12V (normal working voltage DC10V-16V)\u003c\/span\u003e\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eSignal source: DC4V~20V (usual power supply positive trigger, button, PNP sensor, PLC signal, etc.)\u003c\/span\u003e\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eOutput capability: It can control devices within 30v5A or within 220v5A\u003c\/span\u003e\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eQuiescent current: 20mA, working current: 50mA\u003c\/span\u003e\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eService life: more than 100,000 times;\u003c\/span\u003e\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eWorking temperature: -40~85 °C;\u003c\/span\u003e\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eNet weight: about 26g\u003c\/span\u003e\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eSize: 64.2mm*34.8mm*18.5mm\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eFeatures\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\n\u003cul data-mce-fragment=\"1\"\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eVoltage input anti-reverse circuit, worry-free wiring. Signal input optocoupler isolation, strong anti-interference ability. Set the parameter to power off permanent memory. Powerful flash MCU online programming function, according to user needs can contact the manufacturer to customize the required functions.\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eFunction introduction\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\n\u003cul data-mce-fragment=\"1\"\u003e\n\u003cli data-mce-fragment=\"1\"\u003eWhen the power is turned on, the trigger signal is received, the countdown starts, and the relay works. When the timer ends, the relay stops working, the time returns to the setting, and the next trigger signal is waited.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eInstructions\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cul data-mce-fragment=\"1\"\u003e\n\u003cli data-mce-fragment=\"1\"\u003e1).Press K1 to enter the time setting, the hundred digit digital tube starts to flash; press K2 at this time, the hundred digits change; press K1 again, the ten digital tube starts to flash; press K2 at this time, the ten digits change; press again After K1, the digital tube starts to flash. At this time, press K2, the digit of the digit changes; press K1 again to exit the setting, and the digital tube no longer flashes.\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003e2).When the digital tube is normally displayed, press K2, the decimal point is shifted, the decimal point is 0 to 999 seconds in ones digit, the decimal point is 0 to 99.9 seconds in ten digits, and the decimal point is 0 to 999 minutes; the time is set.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e2.Digital Display Delay Controller:(DC 12V 3 Button)\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eProduct parameters\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eWorking voltage: DC12V (normal working voltage DC10V-16V)\u003cbr data-mce-fragment=\"1\"\u003eSource: DC4V~20V (usual power supply positive trigger, button, PNP sensor, PLC signal, etc.)\u003cbr data-mce-fragment=\"1\"\u003eOutput capability: It can control devices within 30v5A or within 220v5A\u003cbr data-mce-fragment=\"1\"\u003eQuiescent current: 20mA, working current: 50mA\u003cbr data-mce-fragment=\"1\"\u003eService life: more than 100,000 times;\u003cbr data-mce-fragment=\"1\"\u003eWorking temperature: -40~85 °C;\u003cbr data-mce-fragment=\"1\"\u003eNet weight: about 26g\u003cbr data-mce-fragment=\"1\"\u003eSize: 64.2mm*34.8mm*18.5mm\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eFeatures\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eVoltage input anti-reverse circuit, worry-free wiring. Signal input optocoupler isolation, strong anti-interference ability. Set the parameter to power off permanent memory. Powerful flash MCU online programming function, according to user needs can contact the manufacturer to customize the required functions.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eWiring diagram\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cimg src=\"https:\/\/pg-cdn-a2.datacaciques.com\/00\/NDAy\/19\/08\/21\/02s76nl1201bce4t\/76050b0dfcc5297c.jpg\" data-mce-fragment=\"1\" data-mce-src=\"https:\/\/pg-cdn-a2.datacaciques.com\/00\/NDAy\/19\/08\/21\/02s76nl1201bce4t\/76050b0dfcc5297c.jpg\"\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eFunction introduction\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eP-1: The signal triggers the relay to pull in. When the time is up, the relay is disconnected during the delay.\u003cbr data-mce-fragment=\"1\"\u003eA: Invalid trigger again B: Re-trigger re-clocking C: Trigger relay reset again to stop timing\u003cbr data-mce-fragment=\"1\"\u003eP-2: The signal trigger start timing time T1, the time is up to the relay pull-in time T2 is disconnected (reset)\u003cbr data-mce-fragment=\"1\"\u003eA: Invalid trigger again B: Re-trigger re-clocking C: Start delay without triggering power-on\u003cbr data-mce-fragment=\"1\"\u003eP-3: Cycling: Turn on T1, disconnect T2, infinite loop. For T1 and T2, the time is adjustable; if a parameter is turned ON or OFF, it can be turned on or the power is turned on.\u003cbr data-mce-fragment=\"1\"\u003eA: The relay is turned on immediately after power-on. B: The relay is turned off and then turned on after power-on.\u003cbr data-mce-fragment=\"1\"\u003eP-4: There is signal, the relay is closed, the suction is kept, the signal disappears, the timing starts, the time is up, the relay is disconnected, during the delay, the signal is given again, the delay is cancelled, the relay is kept, the signal disappears, and the time is re-timed.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cstrong data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eNotes\u003c\/span\u003e\u003c\/strong\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eThe relay output is a passive contact that has no live output and controls the on\/off of a line.\u003c\/span\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e\u003cspan face=\"helveticao\" data-mce-fragment=\"1\"\u003e3.Digital Display Delay Controller:(DC 12V with Buzzer 3 Button)\u003c\/span\u003e\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan face=\"helveticao\" data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eProduct parameters\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eWorking voltage: DC12V (normal working voltage DC10V-16V)\u003cbr data-mce-fragment=\"1\"\u003eSource: DC4V~20V (usual power supply positive trigger, button, PNP sensor, PLC signal, etc.)\u003cbr data-mce-fragment=\"1\"\u003eOutput capability: It can control devices within 30v5A or within 220v5A\u003cbr data-mce-fragment=\"1\"\u003eQuiescent current: 20mA, working current: 50mA\u003cbr data-mce-fragment=\"1\"\u003eService life: more than 100,000 times;\u003cbr data-mce-fragment=\"1\"\u003eWorking temperature: -40~85 °C;\u003cbr data-mce-fragment=\"1\"\u003eNet weight: about 26g\u003cbr data-mce-fragment=\"1\"\u003eSize: 64.2mm*34.8mm*18.5mm\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eFeatures\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003ePower input flash-coupled, strong-interference ability. Power of flash MCU online programming function, according to user needs can contact the manufacturer to customize the Required functions.\u003c\/span\u003e\u003cspan face=\"helveticao\" data-mce-fragment=\"1\"\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003c\/span\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003eFunction introduction\u003cbr data-mce-fragment=\"1\"\u003eP-1: The trigger signal is received, the relay is turned on, the timer expires, and the relay is turned off.\u003cbr data-mce-fragment=\"1\"\u003eA1: Invalid again during delayed trigger\u003cbr data-mce-fragment=\"1\"\u003eA2: Trigger again during retiming delay\u003cbr data-mce-fragment=\"1\"\u003eA3: During the delay trigger, the trigger signal is received again to terminate the current delay.\u003cbr data-mce-fragment=\"1\"\u003eP-2: Receive trigger signal, X start time, relay off, Y start time, relay open\u003cbr data-mce-fragment=\"1\"\u003eP-3: Cycle switching mode\u003cbr data-mce-fragment=\"1\"\u003eA1: After the power relay is turned on, the timing is turned off and the loop is infinite.\u003cbr data-mce-fragment=\"1\"\u003eA2: After the power relay is turned off, the timing ends and the loop is infinite.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cstrong data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eNotes:\u003c\/span\u003e\u003c\/strong\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eThe relay output is a passive contact that has no live output and controls the on\/off of a line.\u003c\/span\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e4.Dual MOS delay control board: (DC 5-30V 4 Button)\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eDescription:\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003eDual MOS parallel active output, lower internal resistance, larger current, strong power interface, clear and simple, powerful, one-button emergency stop function (STOP button), with reverse connection protection, reverse connection, no burning, power-off memory. Increase Sleep mode, after enabling, no operation within 5 minutes, automatically turn off the display, wake up any button! You can set different OP, CL, LOP parameters, these parameters are independent of each other, save the setting parameters automatically power-down save and other functions, Almost all the needs!\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eProduct manual\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eWorking voltage: DC5V-DC30V (wide voltage anti-connection protection)\u003cbr data-mce-fragment=\"1\"\u003eTrigger signal source: high-level trigger DC 3.0V—24V signal ground and system ground to improve the system's anti-interference ability can also short-circuit the ground\u003cbr data-mce-fragment=\"1\"\u003eOutput capacity: DC DC 5V--36V, continuous current 15A at normal temperature, power 400W! Under the condition of auxiliary heat dissipation, the maximum current can reach 30A\u003cbr data-mce-fragment=\"1\"\u003eProduct size: 64mm*35mm*19.3mm\u003cbr data-mce-fragment=\"1\"\u003eMounting hole: diameter 3mm\u003cbr data-mce-fragment=\"1\"\u003eWorking temperature: -40 ° C ~ 85 ° C\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eOperating mode\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eP1 mode: After the signal is triggered, the MOS transistor turns on the OP time and then turns off; in the OP time, the following operation\u003cbr data-mce-fragment=\"1\"\u003eP1.1: The signal is triggered again.\u003cbr data-mce-fragment=\"1\"\u003eP1.2: Signal triggers re-timed again\u003cbr data-mce-fragment=\"1\"\u003eP1.3: The signal triggers reset again, the MOS tube is disconnected, and the timing is stopped.\u003cbr data-mce-fragment=\"1\"\u003eP-2: Give the trigger signal, after the MOS transistor is disconnected from the CL time, the MOS transistor turns on the OP time. After the timing is completed, the MOS transistor is disconnected.\u003cbr data-mce-fragment=\"1\"\u003eP3.1: Give the trigger signal, after the MOS transistor turns on the OP time, the MOS tube turns off the CL time, then loops the above action, the signal is given again in the loop, the MOS tube is disconnected, the timing is stopped; the number of cycles (LOP) can be set.\u003cbr data-mce-fragment=\"1\"\u003eP3.2: No need to trigger signal after power-on, MOS tube turns on OP time, MOS tube disconnects CL time, loops the above action; loop number (LOP) can be set\u003cbr data-mce-fragment=\"1\"\u003eP-4: Signal hold function If there is a trigger signal, the timing is cleared, the MOS transistor remains on; when the signal disappears, the MOS transistor is disconnected after timing the OP; during the timing, there is a signal and the timing is cleared.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eRelay enable mode\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eON : MOS tube is allowed to conduct during OP conduction time\u003cbr data-mce-fragment=\"1\"\u003eOFF : MOS tube is disabled, always off\u003cbr data-mce-fragment=\"1\"\u003eShort press the STOP button on the main interface to switch between ON and OFF. The current state will flash, then return to the main interface. This function is the emergency stop function. One button is used to open and close the MOS tube.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eSleep mode (long press the stop button to view the current mode)\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eC-P sleep mode: within five minutes, without any operation, the digital tube automatically turns off the display, the program runs normally.\u003cbr data-mce-fragment=\"1\"\u003eO-d normal mode: the digital tube is always on display\u003cbr data-mce-fragment=\"1\"\u003ePress and hold the STOP button for 2 seconds and then release to switch the C-P and O-d states. The current state will flash and then return to the main interface.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eTiming range\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eHow to choose the timing range\u003cbr data-mce-fragment=\"1\"\u003e1).After setting the parameter value in the mode selection interface, press the STOP button to select the timing range.\u003cbr data-mce-fragment=\"1\"\u003eXXX. Decimal point is in one place, timing range: 1 second to 999 seconds\u003cbr data-mce-fragment=\"1\"\u003eXX.X decimal point in ten, timing range: 0.1 seconds to 99.9 seconds\u003cbr data-mce-fragment=\"1\"\u003eX.X.X. The decimal point is fully illuminated, the timing range is from 1 minute to 999 minutes.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e2).For example, if you want to set the OP to 3.2 seconds, move the decimal point to ten digits, and the digital tube displays 03.2.\u003cbr data-mce-fragment=\"1\"\u003eParameter description: OP on time, CL off time, LOP cycle number 1-999 times, \"---\" stands for infinite loop.\u003cbr data-mce-fragment=\"1\"\u003eThese parameters are independent of each other, but each mode shares these parameters. For example, when the on-time OP is set to 5 seconds in P1.1, the user wants to switch to the P1.2 mode, then when entering the P1.2 setting corresponding parameters, the OP also It will be 5 seconds.\u003cbr data-mce-fragment=\"1\"\u003eDisplaying 000 on the main interface and pressing the SET button will display OPL, LOP and corresponding time XXX\u003cbr data-mce-fragment=\"1\"\u003eIf only OP in the mode, such as mode P1.1, P1.2, P1.3 time, then short press SET button will only display OP and corresponding time.\u003cbr data-mce-fragment=\"1\"\u003eIf the mode has OP, CL, LOP such as mode P3.1, P3.2 short press SET button will display OP and corresponding time, CL and corresponding time, LOP and corresponding times.\u003cbr data-mce-fragment=\"1\"\u003eAfter setting the mode, it is very convenient to easily check the parameters set in the current mode by pressing the SET button on the main interface.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eHow to set parameters\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e1) First determine the working mode of the MOS tube\u003cbr data-mce-fragment=\"1\"\u003eAccording to the working mode of the MOS tube, in the main interface (when the module is powered on, it will flash the current working mode (default P1.1 mode), then enter the main interface \"press and hold the SET button for 2 seconds and then release\" to enter the mode. Select the interface, press the UP, DOWN button to select the mode to be set P1.1~P-4\u003cbr data-mce-fragment=\"1\"\u003e2) After selecting the mode to be set (for example, P3.2), press the SET button to set the corresponding parameter. At this time, the parameter to be set will flash OP ON time, CL OFF time, LOP cycle number “---” Represents an infinite loop, adjusts the parameter value through UP and DOWN, supports long press (rapid increase or decrease) and short press (increase or decrease 1 unit); after setting the parameter value, select the decimal point position by short pressing the STOP button. , select the timing range (corresponding time 0.1 seconds ~ 999 minutes); short press the SET button to set the next parameter of the current mode, the process is the same as above.\u003cbr data-mce-fragment=\"1\"\u003e3) After setting the parameters of the selected mode, press and hold the SET button for 2 seconds to release, the currently set mode will flash, then return to the main interface and set the parameters successfully.\u003cbr data-mce-fragment=\"1\"\u003e4) Main interface: “000” (no decimal point) is displayed when the MOS tube is not working, and the MOS tube has a decimal point in the working state.\u003cbr data-mce-fragment=\"1\"\u003e5) Mode selection interface: long press SET button to enter, after setting is completed, long press SET button to exit, return to the main interface\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cstrong data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eNote:\u003c\/span\u003e\u003c\/strong\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eThe module is an active live output, and the voltage at the output (load) is equal to the input voltage DC\u003c\/span\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e5.USD Digital Display Delay Controller: ( DC12V 4 Button )\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eDescription:\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003eThis relay delay control board has a powerful and clear interface, powerful function, one-button emergency stop function (STOP button), with reverse connection protection, reverse connection without burning, power-off memory. Increased sleep mode, after enabling, No operation within 5 minutes, automatically turn off the display, wake up any button! You can set different OP, CL, LOP parameters, these parameters are independent of each other, save the setting parameters automatically power-down save and other functions, almost meet all needs!\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eProduct manual:\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eWorking voltage: DC6V-DC30V (wide voltage anti-connection protection)\u003cbr data-mce-fragment=\"1\"\u003eTrigger signal source: high-level trigger DC 3.0V—24V signal ground and system ground to improve the system's anti-interference ability can also short-circuit the ground\u003cbr data-mce-fragment=\"1\"\u003eOutput capacity: controllable DC 30V\/10A or AC 250V\/10A equipment\u003cbr data-mce-fragment=\"1\"\u003eProduct size: 64mm*35mm*19.3mm\u003cbr data-mce-fragment=\"1\"\u003eMounting hole: diameter 3mm\u003cbr data-mce-fragment=\"1\"\u003eWorking temperature: -40 ° C ~ 85 ° C\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e6.DC Motor Speed Controller :(DC 8-55V Motor Speed Controller )\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eDescription:\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003eThis product brings together a wide range of modern motor speed control, with the advantages of small size, simple operation, high current resistance and reverse connection. Suitable for most users in various environments with various speeds, support acceleration and deceleration functions can be set through the menu, with set parameters power off permanent memory function\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eProduct manual:\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eVoltage: DC8V-55V (wide voltage anti-back protection)\u003cbr data-mce-fragment=\"1\"\u003eSpeed range: long press \/ short press to adjust the degree, 0% -100% speed\u003cbr data-mce-fragment=\"1\"\u003eDrive current: up to 10A, (recommended output series 12A fuse)\u003cbr data-mce-fragment=\"1\"\u003eStandby current: \u0026lt;17mA\u003cbr data-mce-fragment=\"1\"\u003eMounting hole: diameter 3mm\u003cbr data-mce-fragment=\"1\"\u003eProduct size: 64mm*35mm*19mm (length * width * height)\u003cbr data-mce-fragment=\"1\"\u003eWorking temperature: -20 ° C ~ 70 ° C\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eInstructions:\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e1. Click\/long press the “speed increase” button to increase the motor speed to 100%.\u003cbr data-mce-fragment=\"1\"\u003e2. Click\/long press the “speed down” button to increase the motor speed to a minimum of 0%.\u003cbr data-mce-fragment=\"1\"\u003e3. Press and hold the “Power On\/Off” button for one second, the controller will be turned on or off (the power is turned off by default, and the memory function is activated after booting)\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003ePrecautions:\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e1. The digital tube flashes at the moment of power-on (normal phenomenon, no need to worry)\u003cbr data-mce-fragment=\"1\"\u003e2, close to the limit drive current working conditions, it is recommended to take the output end of the fuse\u003cbr data-mce-fragment=\"1\"\u003e3. The DC motor speed controller cannot be installed in places where there is dripping water and children can reach it.\u003cbr data-mce-fragment=\"1\"\u003e4. After wiring, check if the line is correct and then energize, so as to avoid accidentally burning the temperature controller and load device.\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003eWiring:\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e“M+” and “M-” are respectively connected to the positive and negative terminals of the output, M+ is positive and M- is negative.\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e“VIN” and “GND” are respectively connected to the positive and negative terminals of the input terminal, Vin is positive and GND is negative (input power supply voltage is DC8V-55V)\u003c\/span\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e7.Temperature Controller:(DC 12V Temperrature Controller)\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eProduct Parameters:\u003c\/span\u003e\u003c\/strong\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003eControl range: -50~110°C\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eResolution: -9.9~99.9, 0.1°C, other temperature range, 1°C\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eTemperature measurement accuracy: 0.1 °C\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eControl accuracy: 0.1 ° C\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eHysteresis accuracy: 0.1 ° C\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eRefresh rate: 0.5S\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eHigh temperature alarm: 0-110 °C\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eMeasurement input: NTC (10K0.5%) waterproof sensor\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eOutput: One way 10A relay\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eEnvironmental requirements: Temperature -10~60°C Humidity 20%-85%\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eSize: 48*40mm\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003ePower consumption of the whole machine: quiescent current: ≤35MA, Pull-in current: ≤65MA\u003c\/span\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eSetting Parameter Method:\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eOnce the power supply and load are connected, the control can be powered. After power-on, the digital tube displays the current real-time temperature. Press the SET button briefly, the digital tube displays the temperature flashing, press the + - button to adjust the set temperature; after the adjustment is completed, press the SET button to save the set temperature and return. At this time, the controller automatically Execute the relay on and off; press and hold the SET button for 5 seconds to enter the menu parameter setting, short press the + - button to switch P0...P6, short press the SET button to enter the menu.\u003cbr data-mce-fragment=\"1\"\u003eThe thermostat output is a 10A relay to meet a variety of high power loads, please ensure that the line is correct.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eIndicator light, digital tube status description:\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eIndicator light: Off means the relay is off, steady light means the relay is closed\u003cbr data-mce-fragment=\"1\"\u003eDigital tube: Display LLL for sensor open circuit: Display HHH is out of measurement range. The thermostat will forcibly open the relay.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eParameter Function Description:\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003ctable data-mce-fragment=\"1\"\u003e\n\u003ctbody data-mce-fragment=\"1\"\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eMenu identifier\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eMenu function\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003ePredetermined area\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eFactory setting\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eP0\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eRefrigeration C \/ Heating H\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eC\/H\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eC\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eP1\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eBacklash\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e0.1-15\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e2.0\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eP2\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eMaximum set temperature\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e-50~110℃\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e110\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eP3\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eMinimum set temperature\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e-50~110℃\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e-50\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eP4\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eTemperature correction\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e-7.0~7.0℃\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e0.0\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eP5\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003ePress delay\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e0-10 minutes\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e0\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eP6\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eHigh temperature alarm\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eON\/OFF\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003eOFF\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003ePackage Included:\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e1PC*DC 12V 2\/3\/4 Button Time Delay Relay Motor Speed Temperrature Controller+Buzzer\u003cstrong data-mce-fragment=\"1\"\u003e(According to your choice)\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e"}
-
Translation missing: en.products.product.regular_price $5.99{"id":6086411911368,"title":"5V\/12V 2\/3\/4 Button Timer Delay Relay Motor Speed Temperature Controller+Buzzer","handle":"5v-12v-2-3-4-button-timer-delay-relay-motor-speed-temperature-controller-buzzer","description":"\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e1.Digital Display Delay Controller:(DC 12V with Buzzer 2 Button\u003cspan face=\"helveticao\" data-mce-fragment=\"1\"\u003e)\u003c\/span\u003e\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eProduct parameters\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\n\u003cul data-mce-fragment=\"1\"\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eWorking voltage: DC12V (normal working voltage DC10V-16V)\u003c\/span\u003e\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eSignal source: DC4V~20V (usual power supply positive trigger, button, PNP sensor, PLC signal, etc.)\u003c\/span\u003e\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eOutput capability: It can control devices within 30v5A or within 220v5A\u003c\/span\u003e\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eQuiescent current: 20mA, working current: 50mA\u003c\/span\u003e\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eService life: more than 100,000 times;\u003c\/span\u003e\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eWorking temperature: -40~85 °C;\u003c\/span\u003e\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eNet weight: about 26g\u003c\/span\u003e\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eSize: 64.2mm*34.8mm*18.5mm\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eFeatures\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\n\u003cul data-mce-fragment=\"1\"\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eVoltage input anti-reverse circuit, worry-free wiring. Signal input optocoupler isolation, strong anti-interference ability. Set the parameter to power off permanent memory. Powerful flash MCU online programming function, according to user needs can contact the manufacturer to customize the required functions.\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eFunction introduction\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\n\u003cul data-mce-fragment=\"1\"\u003e\n\u003cli data-mce-fragment=\"1\"\u003eWhen the power is turned on, the trigger signal is received, the countdown starts, and the relay works. When the timer ends, the relay stops working, the time returns to the setting, and the next trigger signal is waited.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eInstructions\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cul data-mce-fragment=\"1\"\u003e\n\u003cli data-mce-fragment=\"1\"\u003e1).Press K1 to enter the time setting, the hundred digit digital tube starts to flash; press K2 at this time, the hundred digits change; press K1 again, the ten digital tube starts to flash; press K2 at this time, the ten digits change; press again After K1, the digital tube starts to flash. At this time, press K2, the digit of the digit changes; press K1 again to exit the setting, and the digital tube no longer flashes.\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003e2).When the digital tube is normally displayed, press K2, the decimal point is shifted, the decimal point is 0 to 999 seconds in ones digit, the decimal point is 0 to 99.9 seconds in ten digits, and the decimal point is 0 to 999 minutes; the time is set.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e2.Digital Display Delay Controller:(DC 12V 3 Button)\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eProduct parameters\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eWorking voltage: DC12V (normal working voltage DC10V-16V)\u003cbr data-mce-fragment=\"1\"\u003eSource: DC4V~20V (usual power supply positive trigger, button, PNP sensor, PLC signal, etc.)\u003cbr data-mce-fragment=\"1\"\u003eOutput capability: It can control devices within 30v5A or within 220v5A\u003cbr data-mce-fragment=\"1\"\u003eQuiescent current: 20mA, working current: 50mA\u003cbr data-mce-fragment=\"1\"\u003eService life: more than 100,000 times;\u003cbr data-mce-fragment=\"1\"\u003eWorking temperature: -40~85 °C;\u003cbr data-mce-fragment=\"1\"\u003eNet weight: about 26g\u003cbr data-mce-fragment=\"1\"\u003eSize: 64.2mm*34.8mm*18.5mm\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eFeatures\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eVoltage input anti-reverse circuit, worry-free wiring. Signal input optocoupler isolation, strong anti-interference ability. Set the parameter to power off permanent memory. Powerful flash MCU online programming function, according to user needs can contact the manufacturer to customize the required functions.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eWiring diagram\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cimg src=\"https:\/\/pg-cdn-a2.datacaciques.com\/00\/NDAy\/19\/08\/21\/02s76nl1201bce4t\/76050b0dfcc5297c.jpg\" data-mce-fragment=\"1\" data-mce-src=\"https:\/\/pg-cdn-a2.datacaciques.com\/00\/NDAy\/19\/08\/21\/02s76nl1201bce4t\/76050b0dfcc5297c.jpg\"\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eFunction introduction\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eP-1: The signal triggers the relay to pull in. When the time is up, the relay is disconnected during the delay.\u003cbr data-mce-fragment=\"1\"\u003eA: Invalid trigger again B: Re-trigger re-clocking C: Trigger relay reset again to stop timing\u003cbr data-mce-fragment=\"1\"\u003eP-2: The signal trigger start timing time T1, the time is up to the relay pull-in time T2 is disconnected (reset)\u003cbr data-mce-fragment=\"1\"\u003eA: Invalid trigger again B: Re-trigger re-clocking C: Start delay without triggering power-on\u003cbr data-mce-fragment=\"1\"\u003eP-3: Cycling: Turn on T1, disconnect T2, infinite loop. For T1 and T2, the time is adjustable; if a parameter is turned ON or OFF, it can be turned on or the power is turned on.\u003cbr data-mce-fragment=\"1\"\u003eA: The relay is turned on immediately after power-on. B: The relay is turned off and then turned on after power-on.\u003cbr data-mce-fragment=\"1\"\u003eP-4: There is signal, the relay is closed, the suction is kept, the signal disappears, the timing starts, the time is up, the relay is disconnected, during the delay, the signal is given again, the delay is cancelled, the relay is kept, the signal disappears, and the time is re-timed.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cstrong data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eNotes\u003c\/span\u003e\u003c\/strong\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eThe relay output is a passive contact that has no live output and controls the on\/off of a line.\u003c\/span\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e\u003cspan face=\"helveticao\" data-mce-fragment=\"1\"\u003e3.Digital Display Delay Controller:(DC 12V with Buzzer 3 Button)\u003c\/span\u003e\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan face=\"helveticao\" data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eProduct parameters\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eWorking voltage: DC12V (normal working voltage DC10V-16V)\u003cbr data-mce-fragment=\"1\"\u003eSource: DC4V~20V (usual power supply positive trigger, button, PNP sensor, PLC signal, etc.)\u003cbr data-mce-fragment=\"1\"\u003eOutput capability: It can control devices within 30v5A or within 220v5A\u003cbr data-mce-fragment=\"1\"\u003eQuiescent current: 20mA, working current: 50mA\u003cbr data-mce-fragment=\"1\"\u003eService life: more than 100,000 times;\u003cbr data-mce-fragment=\"1\"\u003eWorking temperature: -40~85 °C;\u003cbr data-mce-fragment=\"1\"\u003eNet weight: about 26g\u003cbr data-mce-fragment=\"1\"\u003eSize: 64.2mm*34.8mm*18.5mm\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eFeatures\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003ePower input flash-coupled, strong-interference ability. Power of flash MCU online programming function, according to user needs can contact the manufacturer to customize the Required functions.\u003c\/span\u003e\u003cspan face=\"helveticao\" data-mce-fragment=\"1\"\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003c\/span\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003eFunction introduction\u003cbr data-mce-fragment=\"1\"\u003eP-1: The trigger signal is received, the relay is turned on, the timer expires, and the relay is turned off.\u003cbr data-mce-fragment=\"1\"\u003eA1: Invalid again during delayed trigger\u003cbr data-mce-fragment=\"1\"\u003eA2: Trigger again during retiming delay\u003cbr data-mce-fragment=\"1\"\u003eA3: During the delay trigger, the trigger signal is received again to terminate the current delay.\u003cbr data-mce-fragment=\"1\"\u003eP-2: Receive trigger signal, X start time, relay off, Y start time, relay open\u003cbr data-mce-fragment=\"1\"\u003eP-3: Cycle switching mode\u003cbr data-mce-fragment=\"1\"\u003eA1: After the power relay is turned on, the timing is turned off and the loop is infinite.\u003cbr data-mce-fragment=\"1\"\u003eA2: After the power relay is turned off, the timing ends and the loop is infinite.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cstrong data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eNotes:\u003c\/span\u003e\u003c\/strong\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eThe relay output is a passive contact that has no live output and controls the on\/off of a line.\u003c\/span\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e4.Dual MOS delay control board: (DC 5-30V 4 Button)\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eDescription:\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003eDual MOS parallel active output, lower internal resistance, larger current, strong power interface, clear and simple, powerful, one-button emergency stop function (STOP button), with reverse connection protection, reverse connection, no burning, power-off memory. Increase Sleep mode, after enabling, no operation within 5 minutes, automatically turn off the display, wake up any button! You can set different OP, CL, LOP parameters, these parameters are independent of each other, save the setting parameters automatically power-down save and other functions, Almost all the needs!\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eProduct manual\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eWorking voltage: DC5V-DC30V (wide voltage anti-connection protection)\u003cbr data-mce-fragment=\"1\"\u003eTrigger signal source: high-level trigger DC 3.0V—24V signal ground and system ground to improve the system's anti-interference ability can also short-circuit the ground\u003cbr data-mce-fragment=\"1\"\u003eOutput capacity: DC DC 5V--36V, continuous current 15A at normal temperature, power 400W! Under the condition of auxiliary heat dissipation, the maximum current can reach 30A\u003cbr data-mce-fragment=\"1\"\u003eProduct size: 64mm*35mm*19.3mm\u003cbr data-mce-fragment=\"1\"\u003eMounting hole: diameter 3mm\u003cbr data-mce-fragment=\"1\"\u003eWorking temperature: -40 ° C ~ 85 ° C\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eOperating mode\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eP1 mode: After the signal is triggered, the MOS transistor turns on the OP time and then turns off; in the OP time, the following operation\u003cbr data-mce-fragment=\"1\"\u003eP1.1: The signal is triggered again.\u003cbr data-mce-fragment=\"1\"\u003eP1.2: Signal triggers re-timed again\u003cbr data-mce-fragment=\"1\"\u003eP1.3: The signal triggers reset again, the MOS tube is disconnected, and the timing is stopped.\u003cbr data-mce-fragment=\"1\"\u003eP-2: Give the trigger signal, after the MOS transistor is disconnected from the CL time, the MOS transistor turns on the OP time. After the timing is completed, the MOS transistor is disconnected.\u003cbr data-mce-fragment=\"1\"\u003eP3.1: Give the trigger signal, after the MOS transistor turns on the OP time, the MOS tube turns off the CL time, then loops the above action, the signal is given again in the loop, the MOS tube is disconnected, the timing is stopped; the number of cycles (LOP) can be set.\u003cbr data-mce-fragment=\"1\"\u003eP3.2: No need to trigger signal after power-on, MOS tube turns on OP time, MOS tube disconnects CL time, loops the above action; loop number (LOP) can be set\u003cbr data-mce-fragment=\"1\"\u003eP-4: Signal hold function If there is a trigger signal, the timing is cleared, the MOS transistor remains on; when the signal disappears, the MOS transistor is disconnected after timing the OP; during the timing, there is a signal and the timing is cleared.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eRelay enable mode\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eON : MOS tube is allowed to conduct during OP conduction time\u003cbr data-mce-fragment=\"1\"\u003eOFF : MOS tube is disabled, always off\u003cbr data-mce-fragment=\"1\"\u003eShort press the STOP button on the main interface to switch between ON and OFF. The current state will flash, then return to the main interface. This function is the emergency stop function. One button is used to open and close the MOS tube.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eSleep mode (long press the stop button to view the current mode)\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eC-P sleep mode: within five minutes, without any operation, the digital tube automatically turns off the display, the program runs normally.\u003cbr data-mce-fragment=\"1\"\u003eO-d normal mode: the digital tube is always on display\u003cbr data-mce-fragment=\"1\"\u003ePress and hold the STOP button for 2 seconds and then release to switch the C-P and O-d states. The current state will flash and then return to the main interface.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eTiming range\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eHow to choose the timing range\u003cbr data-mce-fragment=\"1\"\u003e1).After setting the parameter value in the mode selection interface, press the STOP button to select the timing range.\u003cbr data-mce-fragment=\"1\"\u003eXXX. Decimal point is in one place, timing range: 1 second to 999 seconds\u003cbr data-mce-fragment=\"1\"\u003eXX.X decimal point in ten, timing range: 0.1 seconds to 99.9 seconds\u003cbr data-mce-fragment=\"1\"\u003eX.X.X. The decimal point is fully illuminated, the timing range is from 1 minute to 999 minutes.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e2).For example, if you want to set the OP to 3.2 seconds, move the decimal point to ten digits, and the digital tube displays 03.2.\u003cbr data-mce-fragment=\"1\"\u003eParameter description: OP on time, CL off time, LOP cycle number 1-999 times, \"---\" stands for infinite loop.\u003cbr data-mce-fragment=\"1\"\u003eThese parameters are independent of each other, but each mode shares these parameters. For example, when the on-time OP is set to 5 seconds in P1.1, the user wants to switch to the P1.2 mode, then when entering the P1.2 setting corresponding parameters, the OP also It will be 5 seconds.\u003cbr data-mce-fragment=\"1\"\u003eDisplaying 000 on the main interface and pressing the SET button will display OPL, LOP and corresponding time XXX\u003cbr data-mce-fragment=\"1\"\u003eIf only OP in the mode, such as mode P1.1, P1.2, P1.3 time, then short press SET button will only display OP and corresponding time.\u003cbr data-mce-fragment=\"1\"\u003eIf the mode has OP, CL, LOP such as mode P3.1, P3.2 short press SET button will display OP and corresponding time, CL and corresponding time, LOP and corresponding times.\u003cbr data-mce-fragment=\"1\"\u003eAfter setting the mode, it is very convenient to easily check the parameters set in the current mode by pressing the SET button on the main interface.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eHow to set parameters\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e1) First determine the working mode of the MOS tube\u003cbr data-mce-fragment=\"1\"\u003eAccording to the working mode of the MOS tube, in the main interface (when the module is powered on, it will flash the current working mode (default P1.1 mode), then enter the main interface \"press and hold the SET button for 2 seconds and then release\" to enter the mode. Select the interface, press the UP, DOWN button to select the mode to be set P1.1~P-4\u003cbr data-mce-fragment=\"1\"\u003e2) After selecting the mode to be set (for example, P3.2), press the SET button to set the corresponding parameter. At this time, the parameter to be set will flash OP ON time, CL OFF time, LOP cycle number “---” Represents an infinite loop, adjusts the parameter value through UP and DOWN, supports long press (rapid increase or decrease) and short press (increase or decrease 1 unit); after setting the parameter value, select the decimal point position by short pressing the STOP button. , select the timing range (corresponding time 0.1 seconds ~ 999 minutes); short press the SET button to set the next parameter of the current mode, the process is the same as above.\u003cbr data-mce-fragment=\"1\"\u003e3) After setting the parameters of the selected mode, press and hold the SET button for 2 seconds to release, the currently set mode will flash, then return to the main interface and set the parameters successfully.\u003cbr data-mce-fragment=\"1\"\u003e4) Main interface: “000” (no decimal point) is displayed when the MOS tube is not working, and the MOS tube has a decimal point in the working state.\u003cbr data-mce-fragment=\"1\"\u003e5) Mode selection interface: long press SET button to enter, after setting is completed, long press SET button to exit, return to the main interface\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cstrong data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eNote:\u003c\/span\u003e\u003c\/strong\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eThe module is an active live output, and the voltage at the output (load) is equal to the input voltage DC\u003c\/span\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e5.USD Digital Display Delay Controller: ( DC12V 4 Button )\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eDescription:\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003eThis relay delay control board has a powerful and clear interface, powerful function, one-button emergency stop function (STOP button), with reverse connection protection, reverse connection without burning, power-off memory. Increased sleep mode, after enabling, No operation within 5 minutes, automatically turn off the display, wake up any button! You can set different OP, CL, LOP parameters, these parameters are independent of each other, save the setting parameters automatically power-down save and other functions, almost meet all needs!\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eProduct manual:\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eWorking voltage: DC6V-DC30V (wide voltage anti-connection protection)\u003cbr data-mce-fragment=\"1\"\u003eTrigger signal source: high-level trigger DC 3.0V—24V signal ground and system ground to improve the system's anti-interference ability can also short-circuit the ground\u003cbr data-mce-fragment=\"1\"\u003eOutput capacity: controllable DC 30V\/10A or AC 250V\/10A equipment\u003cbr data-mce-fragment=\"1\"\u003eProduct size: 64mm*35mm*19.3mm\u003cbr data-mce-fragment=\"1\"\u003eMounting hole: diameter 3mm\u003cbr data-mce-fragment=\"1\"\u003eWorking temperature: -40 ° C ~ 85 ° C\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e6.DC Motor Speed Controller :(DC 8-55V Motor Speed Controller )\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eDescription:\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003eThis product brings together a wide range of modern motor speed control, with the advantages of small size, simple operation, high current resistance and reverse connection. Suitable for most users in various environments with various speeds, support acceleration and deceleration functions can be set through the menu, with set parameters power off permanent memory function\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eProduct manual:\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eVoltage: DC8V-55V (wide voltage anti-back protection)\u003cbr data-mce-fragment=\"1\"\u003eSpeed range: long press \/ short press to adjust the degree, 0% -100% speed\u003cbr data-mce-fragment=\"1\"\u003eDrive current: up to 10A, (recommended output series 12A fuse)\u003cbr data-mce-fragment=\"1\"\u003eStandby current: \u0026lt;17mA\u003cbr data-mce-fragment=\"1\"\u003eMounting hole: diameter 3mm\u003cbr data-mce-fragment=\"1\"\u003eProduct size: 64mm*35mm*19mm (length * width * height)\u003cbr data-mce-fragment=\"1\"\u003eWorking temperature: -20 ° C ~ 70 ° C\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eInstructions:\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e1. Click\/long press the “speed increase” button to increase the motor speed to 100%.\u003cbr data-mce-fragment=\"1\"\u003e2. Click\/long press the “speed down” button to increase the motor speed to a minimum of 0%.\u003cbr data-mce-fragment=\"1\"\u003e3. Press and hold the “Power On\/Off” button for one second, the controller will be turned on or off (the power is turned off by default, and the memory function is activated after booting)\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003ePrecautions:\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e1. The digital tube flashes at the moment of power-on (normal phenomenon, no need to worry)\u003cbr data-mce-fragment=\"1\"\u003e2, close to the limit drive current working conditions, it is recommended to take the output end of the fuse\u003cbr data-mce-fragment=\"1\"\u003e3. The DC motor speed controller cannot be installed in places where there is dripping water and children can reach it.\u003cbr data-mce-fragment=\"1\"\u003e4. After wiring, check if the line is correct and then energize, so as to avoid accidentally burning the temperature controller and load device.\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003eWiring:\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e“M+” and “M-” are respectively connected to the positive and negative terminals of the output, M+ is positive and M- is negative.\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e“VIN” and “GND” are respectively connected to the positive and negative terminals of the input terminal, Vin is positive and GND is negative (input power supply voltage is DC8V-55V)\u003c\/span\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e7.Temperature Controller:(DC 12V Temperrature Controller)\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eProduct Parameters:\u003c\/span\u003e\u003c\/strong\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003eControl range: -50~110°C\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eResolution: -9.9~99.9, 0.1°C, other temperature range, 1°C\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eTemperature measurement accuracy: 0.1 °C\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eControl accuracy: 0.1 ° C\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eHysteresis accuracy: 0.1 ° C\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eRefresh rate: 0.5S\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eHigh temperature alarm: 0-110 °C\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eMeasurement input: NTC (10K0.5%) waterproof sensor\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eOutput: One way 10A relay\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eEnvironmental requirements: Temperature -10~60°C Humidity 20%-85%\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eSize: 48*40mm\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003ePower consumption of the whole machine: quiescent current: ≤35MA, Pull-in current: ≤65MA\u003c\/span\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eSetting Parameter Method:\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eOnce the power supply and load are connected, the control can be powered. After power-on, the digital tube displays the current real-time temperature. Press the SET button briefly, the digital tube displays the temperature flashing, press the + - button to adjust the set temperature; after the adjustment is completed, press the SET button to save the set temperature and return. At this time, the controller automatically Execute the relay on and off; press and hold the SET button for 5 seconds to enter the menu parameter setting, short press the + - button to switch P0...P6, short press the SET button to enter the menu.\u003cbr data-mce-fragment=\"1\"\u003eThe thermostat output is a 10A relay to meet a variety of high power loads, please ensure that the line is correct.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eIndicator light, digital tube status description:\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eIndicator light: Off means the relay is off, steady light means the relay is closed\u003cbr data-mce-fragment=\"1\"\u003eDigital tube: Display LLL for sensor open circuit: Display HHH is out of measurement range. The thermostat will forcibly open the relay.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eParameter Function Description:\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003ctable data-mce-fragment=\"1\"\u003e\n\u003ctbody data-mce-fragment=\"1\"\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eMenu identifier\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eMenu function\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003ePredetermined area\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eFactory setting\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eP0\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eRefrigeration C \/ Heating H\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eC\/H\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eC\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eP1\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eBacklash\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e0.1-15\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e2.0\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eP2\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eMaximum set temperature\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e-50~110℃\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e110\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eP3\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eMinimum set temperature\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e-50~110℃\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e-50\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eP4\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eTemperature correction\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e-7.0~7.0℃\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e0.0\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eP5\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003ePress delay\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e0-10 minutes\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e0\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eP6\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eHigh temperature alarm\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eON\/OFF\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003eOFF\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003ePackage Included:\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e1PC*DC 12V 2\/3\/4 Button Time Delay Relay Motor Speed Temperrature Controller+Buzzer\u003cstrong data-mce-fragment=\"1\"\u003e(According to your choice)\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e","published_at":"2020-11-17T14:10:21+08:00","created_at":"2020-11-17T14:10:20+08:00","vendor":"DIYMORE","type":"","tags":[],"price":899,"price_min":899,"price_max":899,"available":true,"price_varies":false,"compare_at_price":null,"compare_at_price_min":0,"compare_at_price_max":0,"compare_at_price_varies":false,"variants":[{"id":37539263873224,"title":"DC 8-55V Motor Speed Controller","option1":"DC 8-55V Motor Speed Controller","option2":null,"option3":null,"sku":"100040","requires_shipping":true,"taxable":false,"featured_image":null,"available":true,"name":"5V\/12V 2\/3\/4 Button Timer Delay Relay Motor Speed Temperature Controller+Buzzer - DC 8-55V Motor Speed Controller","public_title":"DC 8-55V Motor Speed Controller","options":["DC 8-55V Motor Speed Controller"],"price":899,"weight":0,"compare_at_price":null,"inventory_management":"shopify","barcode":"","requires_selling_plan":false,"selling_plan_allocations":[]}],"images":["\/\/www.diymore.cc\/cdn\/shop\/products\/100040_1.jpg?v=1605593426","\/\/www.diymore.cc\/cdn\/shop\/products\/100040_2.jpg?v=1605593426","\/\/www.diymore.cc\/cdn\/shop\/products\/100040.jpg?v=1605593426","\/\/www.diymore.cc\/cdn\/shop\/products\/100040_8.jpg?v=1605593426","\/\/www.diymore.cc\/cdn\/shop\/products\/100040_867e837f-1764-4e74-953c-5a0322a10abe.jpg?v=1605593426","\/\/www.diymore.cc\/cdn\/shop\/products\/100040_7.jpg?v=1605593426","\/\/www.diymore.cc\/cdn\/shop\/products\/100040_4.jpg?v=1605593426","\/\/www.diymore.cc\/cdn\/shop\/products\/100040_5.jpg?v=1605593427","\/\/www.diymore.cc\/cdn\/shop\/products\/100040_6.jpg?v=1605593427","\/\/www.diymore.cc\/cdn\/shop\/products\/100040_3.jpg?v=1605593427"],"featured_image":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040_1.jpg?v=1605593426","options":["Size"],"media":[{"alt":null,"id":14960171581640,"position":1,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040_1.jpg?v=1605593426"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040_1.jpg?v=1605593426","width":1000},{"alt":null,"id":14960171614408,"position":2,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040_2.jpg?v=1605593426"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040_2.jpg?v=1605593426","width":1000},{"alt":null,"id":14960171647176,"position":3,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040.jpg?v=1605593426"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040.jpg?v=1605593426","width":1000},{"alt":null,"id":14960171679944,"position":4,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040_8.jpg?v=1605593426"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040_8.jpg?v=1605593426","width":1000},{"alt":null,"id":14960171712712,"position":5,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040_867e837f-1764-4e74-953c-5a0322a10abe.jpg?v=1605593426"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040_867e837f-1764-4e74-953c-5a0322a10abe.jpg?v=1605593426","width":1000},{"alt":null,"id":14960171745480,"position":6,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040_7.jpg?v=1605593426"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040_7.jpg?v=1605593426","width":1000},{"alt":null,"id":14960171778248,"position":7,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040_4.jpg?v=1605593426"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040_4.jpg?v=1605593426","width":1000},{"alt":null,"id":14960171811016,"position":8,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040_5.jpg?v=1605593427"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040_5.jpg?v=1605593427","width":1000},{"alt":null,"id":14960171843784,"position":9,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040_6.jpg?v=1605593427"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040_6.jpg?v=1605593427","width":1000},{"alt":null,"id":14960171876552,"position":10,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040_3.jpg?v=1605593427"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040_3.jpg?v=1605593427","width":1000}],"requires_selling_plan":false,"selling_plan_groups":[],"content":"\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e1.Digital Display Delay Controller:(DC 12V with Buzzer 2 Button\u003cspan face=\"helveticao\" data-mce-fragment=\"1\"\u003e)\u003c\/span\u003e\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eProduct parameters\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\n\u003cul data-mce-fragment=\"1\"\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eWorking voltage: DC12V (normal working voltage DC10V-16V)\u003c\/span\u003e\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eSignal source: DC4V~20V (usual power supply positive trigger, button, PNP sensor, PLC signal, etc.)\u003c\/span\u003e\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eOutput capability: It can control devices within 30v5A or within 220v5A\u003c\/span\u003e\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eQuiescent current: 20mA, working current: 50mA\u003c\/span\u003e\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eService life: more than 100,000 times;\u003c\/span\u003e\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eWorking temperature: -40~85 °C;\u003c\/span\u003e\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eNet weight: about 26g\u003c\/span\u003e\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eSize: 64.2mm*34.8mm*18.5mm\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eFeatures\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\n\u003cul data-mce-fragment=\"1\"\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eVoltage input anti-reverse circuit, worry-free wiring. Signal input optocoupler isolation, strong anti-interference ability. Set the parameter to power off permanent memory. Powerful flash MCU online programming function, according to user needs can contact the manufacturer to customize the required functions.\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eFunction introduction\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\n\u003cul data-mce-fragment=\"1\"\u003e\n\u003cli data-mce-fragment=\"1\"\u003eWhen the power is turned on, the trigger signal is received, the countdown starts, and the relay works. When the timer ends, the relay stops working, the time returns to the setting, and the next trigger signal is waited.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eInstructions\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cul data-mce-fragment=\"1\"\u003e\n\u003cli data-mce-fragment=\"1\"\u003e1).Press K1 to enter the time setting, the hundred digit digital tube starts to flash; press K2 at this time, the hundred digits change; press K1 again, the ten digital tube starts to flash; press K2 at this time, the ten digits change; press again After K1, the digital tube starts to flash. At this time, press K2, the digit of the digit changes; press K1 again to exit the setting, and the digital tube no longer flashes.\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003e2).When the digital tube is normally displayed, press K2, the decimal point is shifted, the decimal point is 0 to 999 seconds in ones digit, the decimal point is 0 to 99.9 seconds in ten digits, and the decimal point is 0 to 999 minutes; the time is set.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e2.Digital Display Delay Controller:(DC 12V 3 Button)\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eProduct parameters\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eWorking voltage: DC12V (normal working voltage DC10V-16V)\u003cbr data-mce-fragment=\"1\"\u003eSource: DC4V~20V (usual power supply positive trigger, button, PNP sensor, PLC signal, etc.)\u003cbr data-mce-fragment=\"1\"\u003eOutput capability: It can control devices within 30v5A or within 220v5A\u003cbr data-mce-fragment=\"1\"\u003eQuiescent current: 20mA, working current: 50mA\u003cbr data-mce-fragment=\"1\"\u003eService life: more than 100,000 times;\u003cbr data-mce-fragment=\"1\"\u003eWorking temperature: -40~85 °C;\u003cbr data-mce-fragment=\"1\"\u003eNet weight: about 26g\u003cbr data-mce-fragment=\"1\"\u003eSize: 64.2mm*34.8mm*18.5mm\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eFeatures\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eVoltage input anti-reverse circuit, worry-free wiring. Signal input optocoupler isolation, strong anti-interference ability. Set the parameter to power off permanent memory. Powerful flash MCU online programming function, according to user needs can contact the manufacturer to customize the required functions.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eWiring diagram\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cimg src=\"https:\/\/pg-cdn-a2.datacaciques.com\/00\/NDAy\/19\/08\/21\/02s76nl1201bce4t\/76050b0dfcc5297c.jpg\" data-mce-fragment=\"1\" data-mce-src=\"https:\/\/pg-cdn-a2.datacaciques.com\/00\/NDAy\/19\/08\/21\/02s76nl1201bce4t\/76050b0dfcc5297c.jpg\"\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eFunction introduction\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eP-1: The signal triggers the relay to pull in. When the time is up, the relay is disconnected during the delay.\u003cbr data-mce-fragment=\"1\"\u003eA: Invalid trigger again B: Re-trigger re-clocking C: Trigger relay reset again to stop timing\u003cbr data-mce-fragment=\"1\"\u003eP-2: The signal trigger start timing time T1, the time is up to the relay pull-in time T2 is disconnected (reset)\u003cbr data-mce-fragment=\"1\"\u003eA: Invalid trigger again B: Re-trigger re-clocking C: Start delay without triggering power-on\u003cbr data-mce-fragment=\"1\"\u003eP-3: Cycling: Turn on T1, disconnect T2, infinite loop. For T1 and T2, the time is adjustable; if a parameter is turned ON or OFF, it can be turned on or the power is turned on.\u003cbr data-mce-fragment=\"1\"\u003eA: The relay is turned on immediately after power-on. B: The relay is turned off and then turned on after power-on.\u003cbr data-mce-fragment=\"1\"\u003eP-4: There is signal, the relay is closed, the suction is kept, the signal disappears, the timing starts, the time is up, the relay is disconnected, during the delay, the signal is given again, the delay is cancelled, the relay is kept, the signal disappears, and the time is re-timed.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cstrong data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eNotes\u003c\/span\u003e\u003c\/strong\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eThe relay output is a passive contact that has no live output and controls the on\/off of a line.\u003c\/span\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e\u003cspan face=\"helveticao\" data-mce-fragment=\"1\"\u003e3.Digital Display Delay Controller:(DC 12V with Buzzer 3 Button)\u003c\/span\u003e\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan face=\"helveticao\" data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eProduct parameters\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eWorking voltage: DC12V (normal working voltage DC10V-16V)\u003cbr data-mce-fragment=\"1\"\u003eSource: DC4V~20V (usual power supply positive trigger, button, PNP sensor, PLC signal, etc.)\u003cbr data-mce-fragment=\"1\"\u003eOutput capability: It can control devices within 30v5A or within 220v5A\u003cbr data-mce-fragment=\"1\"\u003eQuiescent current: 20mA, working current: 50mA\u003cbr data-mce-fragment=\"1\"\u003eService life: more than 100,000 times;\u003cbr data-mce-fragment=\"1\"\u003eWorking temperature: -40~85 °C;\u003cbr data-mce-fragment=\"1\"\u003eNet weight: about 26g\u003cbr data-mce-fragment=\"1\"\u003eSize: 64.2mm*34.8mm*18.5mm\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eFeatures\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003ePower input flash-coupled, strong-interference ability. Power of flash MCU online programming function, according to user needs can contact the manufacturer to customize the Required functions.\u003c\/span\u003e\u003cspan face=\"helveticao\" data-mce-fragment=\"1\"\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003c\/span\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003eFunction introduction\u003cbr data-mce-fragment=\"1\"\u003eP-1: The trigger signal is received, the relay is turned on, the timer expires, and the relay is turned off.\u003cbr data-mce-fragment=\"1\"\u003eA1: Invalid again during delayed trigger\u003cbr data-mce-fragment=\"1\"\u003eA2: Trigger again during retiming delay\u003cbr data-mce-fragment=\"1\"\u003eA3: During the delay trigger, the trigger signal is received again to terminate the current delay.\u003cbr data-mce-fragment=\"1\"\u003eP-2: Receive trigger signal, X start time, relay off, Y start time, relay open\u003cbr data-mce-fragment=\"1\"\u003eP-3: Cycle switching mode\u003cbr data-mce-fragment=\"1\"\u003eA1: After the power relay is turned on, the timing is turned off and the loop is infinite.\u003cbr data-mce-fragment=\"1\"\u003eA2: After the power relay is turned off, the timing ends and the loop is infinite.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cstrong data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eNotes:\u003c\/span\u003e\u003c\/strong\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eThe relay output is a passive contact that has no live output and controls the on\/off of a line.\u003c\/span\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e4.Dual MOS delay control board: (DC 5-30V 4 Button)\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eDescription:\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003eDual MOS parallel active output, lower internal resistance, larger current, strong power interface, clear and simple, powerful, one-button emergency stop function (STOP button), with reverse connection protection, reverse connection, no burning, power-off memory. Increase Sleep mode, after enabling, no operation within 5 minutes, automatically turn off the display, wake up any button! You can set different OP, CL, LOP parameters, these parameters are independent of each other, save the setting parameters automatically power-down save and other functions, Almost all the needs!\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eProduct manual\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eWorking voltage: DC5V-DC30V (wide voltage anti-connection protection)\u003cbr data-mce-fragment=\"1\"\u003eTrigger signal source: high-level trigger DC 3.0V—24V signal ground and system ground to improve the system's anti-interference ability can also short-circuit the ground\u003cbr data-mce-fragment=\"1\"\u003eOutput capacity: DC DC 5V--36V, continuous current 15A at normal temperature, power 400W! Under the condition of auxiliary heat dissipation, the maximum current can reach 30A\u003cbr data-mce-fragment=\"1\"\u003eProduct size: 64mm*35mm*19.3mm\u003cbr data-mce-fragment=\"1\"\u003eMounting hole: diameter 3mm\u003cbr data-mce-fragment=\"1\"\u003eWorking temperature: -40 ° C ~ 85 ° C\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eOperating mode\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eP1 mode: After the signal is triggered, the MOS transistor turns on the OP time and then turns off; in the OP time, the following operation\u003cbr data-mce-fragment=\"1\"\u003eP1.1: The signal is triggered again.\u003cbr data-mce-fragment=\"1\"\u003eP1.2: Signal triggers re-timed again\u003cbr data-mce-fragment=\"1\"\u003eP1.3: The signal triggers reset again, the MOS tube is disconnected, and the timing is stopped.\u003cbr data-mce-fragment=\"1\"\u003eP-2: Give the trigger signal, after the MOS transistor is disconnected from the CL time, the MOS transistor turns on the OP time. After the timing is completed, the MOS transistor is disconnected.\u003cbr data-mce-fragment=\"1\"\u003eP3.1: Give the trigger signal, after the MOS transistor turns on the OP time, the MOS tube turns off the CL time, then loops the above action, the signal is given again in the loop, the MOS tube is disconnected, the timing is stopped; the number of cycles (LOP) can be set.\u003cbr data-mce-fragment=\"1\"\u003eP3.2: No need to trigger signal after power-on, MOS tube turns on OP time, MOS tube disconnects CL time, loops the above action; loop number (LOP) can be set\u003cbr data-mce-fragment=\"1\"\u003eP-4: Signal hold function If there is a trigger signal, the timing is cleared, the MOS transistor remains on; when the signal disappears, the MOS transistor is disconnected after timing the OP; during the timing, there is a signal and the timing is cleared.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eRelay enable mode\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eON : MOS tube is allowed to conduct during OP conduction time\u003cbr data-mce-fragment=\"1\"\u003eOFF : MOS tube is disabled, always off\u003cbr data-mce-fragment=\"1\"\u003eShort press the STOP button on the main interface to switch between ON and OFF. The current state will flash, then return to the main interface. This function is the emergency stop function. One button is used to open and close the MOS tube.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eSleep mode (long press the stop button to view the current mode)\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eC-P sleep mode: within five minutes, without any operation, the digital tube automatically turns off the display, the program runs normally.\u003cbr data-mce-fragment=\"1\"\u003eO-d normal mode: the digital tube is always on display\u003cbr data-mce-fragment=\"1\"\u003ePress and hold the STOP button for 2 seconds and then release to switch the C-P and O-d states. The current state will flash and then return to the main interface.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eTiming range\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eHow to choose the timing range\u003cbr data-mce-fragment=\"1\"\u003e1).After setting the parameter value in the mode selection interface, press the STOP button to select the timing range.\u003cbr data-mce-fragment=\"1\"\u003eXXX. Decimal point is in one place, timing range: 1 second to 999 seconds\u003cbr data-mce-fragment=\"1\"\u003eXX.X decimal point in ten, timing range: 0.1 seconds to 99.9 seconds\u003cbr data-mce-fragment=\"1\"\u003eX.X.X. The decimal point is fully illuminated, the timing range is from 1 minute to 999 minutes.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e2).For example, if you want to set the OP to 3.2 seconds, move the decimal point to ten digits, and the digital tube displays 03.2.\u003cbr data-mce-fragment=\"1\"\u003eParameter description: OP on time, CL off time, LOP cycle number 1-999 times, \"---\" stands for infinite loop.\u003cbr data-mce-fragment=\"1\"\u003eThese parameters are independent of each other, but each mode shares these parameters. For example, when the on-time OP is set to 5 seconds in P1.1, the user wants to switch to the P1.2 mode, then when entering the P1.2 setting corresponding parameters, the OP also It will be 5 seconds.\u003cbr data-mce-fragment=\"1\"\u003eDisplaying 000 on the main interface and pressing the SET button will display OPL, LOP and corresponding time XXX\u003cbr data-mce-fragment=\"1\"\u003eIf only OP in the mode, such as mode P1.1, P1.2, P1.3 time, then short press SET button will only display OP and corresponding time.\u003cbr data-mce-fragment=\"1\"\u003eIf the mode has OP, CL, LOP such as mode P3.1, P3.2 short press SET button will display OP and corresponding time, CL and corresponding time, LOP and corresponding times.\u003cbr data-mce-fragment=\"1\"\u003eAfter setting the mode, it is very convenient to easily check the parameters set in the current mode by pressing the SET button on the main interface.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eHow to set parameters\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e1) First determine the working mode of the MOS tube\u003cbr data-mce-fragment=\"1\"\u003eAccording to the working mode of the MOS tube, in the main interface (when the module is powered on, it will flash the current working mode (default P1.1 mode), then enter the main interface \"press and hold the SET button for 2 seconds and then release\" to enter the mode. Select the interface, press the UP, DOWN button to select the mode to be set P1.1~P-4\u003cbr data-mce-fragment=\"1\"\u003e2) After selecting the mode to be set (for example, P3.2), press the SET button to set the corresponding parameter. At this time, the parameter to be set will flash OP ON time, CL OFF time, LOP cycle number “---” Represents an infinite loop, adjusts the parameter value through UP and DOWN, supports long press (rapid increase or decrease) and short press (increase or decrease 1 unit); after setting the parameter value, select the decimal point position by short pressing the STOP button. , select the timing range (corresponding time 0.1 seconds ~ 999 minutes); short press the SET button to set the next parameter of the current mode, the process is the same as above.\u003cbr data-mce-fragment=\"1\"\u003e3) After setting the parameters of the selected mode, press and hold the SET button for 2 seconds to release, the currently set mode will flash, then return to the main interface and set the parameters successfully.\u003cbr data-mce-fragment=\"1\"\u003e4) Main interface: “000” (no decimal point) is displayed when the MOS tube is not working, and the MOS tube has a decimal point in the working state.\u003cbr data-mce-fragment=\"1\"\u003e5) Mode selection interface: long press SET button to enter, after setting is completed, long press SET button to exit, return to the main interface\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cstrong data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eNote:\u003c\/span\u003e\u003c\/strong\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eThe module is an active live output, and the voltage at the output (load) is equal to the input voltage DC\u003c\/span\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e5.USD Digital Display Delay Controller: ( DC12V 4 Button )\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eDescription:\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003eThis relay delay control board has a powerful and clear interface, powerful function, one-button emergency stop function (STOP button), with reverse connection protection, reverse connection without burning, power-off memory. Increased sleep mode, after enabling, No operation within 5 minutes, automatically turn off the display, wake up any button! You can set different OP, CL, LOP parameters, these parameters are independent of each other, save the setting parameters automatically power-down save and other functions, almost meet all needs!\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eProduct manual:\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eWorking voltage: DC6V-DC30V (wide voltage anti-connection protection)\u003cbr data-mce-fragment=\"1\"\u003eTrigger signal source: high-level trigger DC 3.0V—24V signal ground and system ground to improve the system's anti-interference ability can also short-circuit the ground\u003cbr data-mce-fragment=\"1\"\u003eOutput capacity: controllable DC 30V\/10A or AC 250V\/10A equipment\u003cbr data-mce-fragment=\"1\"\u003eProduct size: 64mm*35mm*19.3mm\u003cbr data-mce-fragment=\"1\"\u003eMounting hole: diameter 3mm\u003cbr data-mce-fragment=\"1\"\u003eWorking temperature: -40 ° C ~ 85 ° C\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e6.DC Motor Speed Controller :(DC 8-55V Motor Speed Controller )\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eDescription:\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003eThis product brings together a wide range of modern motor speed control, with the advantages of small size, simple operation, high current resistance and reverse connection. Suitable for most users in various environments with various speeds, support acceleration and deceleration functions can be set through the menu, with set parameters power off permanent memory function\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eProduct manual:\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eVoltage: DC8V-55V (wide voltage anti-back protection)\u003cbr data-mce-fragment=\"1\"\u003eSpeed range: long press \/ short press to adjust the degree, 0% -100% speed\u003cbr data-mce-fragment=\"1\"\u003eDrive current: up to 10A, (recommended output series 12A fuse)\u003cbr data-mce-fragment=\"1\"\u003eStandby current: \u0026lt;17mA\u003cbr data-mce-fragment=\"1\"\u003eMounting hole: diameter 3mm\u003cbr data-mce-fragment=\"1\"\u003eProduct size: 64mm*35mm*19mm (length * width * height)\u003cbr data-mce-fragment=\"1\"\u003eWorking temperature: -20 ° C ~ 70 ° C\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eInstructions:\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e1. Click\/long press the “speed increase” button to increase the motor speed to 100%.\u003cbr data-mce-fragment=\"1\"\u003e2. Click\/long press the “speed down” button to increase the motor speed to a minimum of 0%.\u003cbr data-mce-fragment=\"1\"\u003e3. Press and hold the “Power On\/Off” button for one second, the controller will be turned on or off (the power is turned off by default, and the memory function is activated after booting)\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003ePrecautions:\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e1. The digital tube flashes at the moment of power-on (normal phenomenon, no need to worry)\u003cbr data-mce-fragment=\"1\"\u003e2, close to the limit drive current working conditions, it is recommended to take the output end of the fuse\u003cbr data-mce-fragment=\"1\"\u003e3. The DC motor speed controller cannot be installed in places where there is dripping water and children can reach it.\u003cbr data-mce-fragment=\"1\"\u003e4. After wiring, check if the line is correct and then energize, so as to avoid accidentally burning the temperature controller and load device.\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003eWiring:\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e“M+” and “M-” are respectively connected to the positive and negative terminals of the output, M+ is positive and M- is negative.\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e“VIN” and “GND” are respectively connected to the positive and negative terminals of the input terminal, Vin is positive and GND is negative (input power supply voltage is DC8V-55V)\u003c\/span\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e7.Temperature Controller:(DC 12V Temperrature Controller)\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eProduct Parameters:\u003c\/span\u003e\u003c\/strong\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003eControl range: -50~110°C\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eResolution: -9.9~99.9, 0.1°C, other temperature range, 1°C\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eTemperature measurement accuracy: 0.1 °C\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eControl accuracy: 0.1 ° C\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eHysteresis accuracy: 0.1 ° C\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eRefresh rate: 0.5S\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eHigh temperature alarm: 0-110 °C\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eMeasurement input: NTC (10K0.5%) waterproof sensor\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eOutput: One way 10A relay\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eEnvironmental requirements: Temperature -10~60°C Humidity 20%-85%\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eSize: 48*40mm\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003ePower consumption of the whole machine: quiescent current: ≤35MA, Pull-in current: ≤65MA\u003c\/span\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eSetting Parameter Method:\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eOnce the power supply and load are connected, the control can be powered. After power-on, the digital tube displays the current real-time temperature. Press the SET button briefly, the digital tube displays the temperature flashing, press the + - button to adjust the set temperature; after the adjustment is completed, press the SET button to save the set temperature and return. At this time, the controller automatically Execute the relay on and off; press and hold the SET button for 5 seconds to enter the menu parameter setting, short press the + - button to switch P0...P6, short press the SET button to enter the menu.\u003cbr data-mce-fragment=\"1\"\u003eThe thermostat output is a 10A relay to meet a variety of high power loads, please ensure that the line is correct.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eIndicator light, digital tube status description:\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eIndicator light: Off means the relay is off, steady light means the relay is closed\u003cbr data-mce-fragment=\"1\"\u003eDigital tube: Display LLL for sensor open circuit: Display HHH is out of measurement range. The thermostat will forcibly open the relay.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eParameter Function Description:\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003ctable data-mce-fragment=\"1\"\u003e\n\u003ctbody data-mce-fragment=\"1\"\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eMenu identifier\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eMenu function\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003ePredetermined area\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eFactory setting\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eP0\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eRefrigeration C \/ Heating H\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eC\/H\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eC\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eP1\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eBacklash\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e0.1-15\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e2.0\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eP2\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eMaximum set temperature\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e-50~110℃\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e110\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eP3\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eMinimum set temperature\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e-50~110℃\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e-50\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eP4\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eTemperature correction\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e-7.0~7.0℃\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e0.0\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eP5\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003ePress delay\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e0-10 minutes\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e0\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eP6\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eHigh temperature alarm\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eON\/OFF\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003eOFF\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003ePackage Included:\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e1PC*DC 12V 2\/3\/4 Button Time Delay Relay Motor Speed Temperrature Controller+Buzzer\u003cstrong data-mce-fragment=\"1\"\u003e(According to your choice)\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e"}
-
Translation missing: en.products.product.regular_price $7.99{"id":6086411911368,"title":"5V\/12V 2\/3\/4 Button Timer Delay Relay Motor Speed Temperature Controller+Buzzer","handle":"5v-12v-2-3-4-button-timer-delay-relay-motor-speed-temperature-controller-buzzer","description":"\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e1.Digital Display Delay Controller:(DC 12V with Buzzer 2 Button\u003cspan face=\"helveticao\" data-mce-fragment=\"1\"\u003e)\u003c\/span\u003e\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eProduct parameters\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\n\u003cul data-mce-fragment=\"1\"\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eWorking voltage: DC12V (normal working voltage DC10V-16V)\u003c\/span\u003e\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eSignal source: DC4V~20V (usual power supply positive trigger, button, PNP sensor, PLC signal, etc.)\u003c\/span\u003e\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eOutput capability: It can control devices within 30v5A or within 220v5A\u003c\/span\u003e\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eQuiescent current: 20mA, working current: 50mA\u003c\/span\u003e\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eService life: more than 100,000 times;\u003c\/span\u003e\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eWorking temperature: -40~85 °C;\u003c\/span\u003e\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eNet weight: about 26g\u003c\/span\u003e\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eSize: 64.2mm*34.8mm*18.5mm\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eFeatures\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\n\u003cul data-mce-fragment=\"1\"\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eVoltage input anti-reverse circuit, worry-free wiring. Signal input optocoupler isolation, strong anti-interference ability. Set the parameter to power off permanent memory. Powerful flash MCU online programming function, according to user needs can contact the manufacturer to customize the required functions.\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eFunction introduction\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\n\u003cul data-mce-fragment=\"1\"\u003e\n\u003cli data-mce-fragment=\"1\"\u003eWhen the power is turned on, the trigger signal is received, the countdown starts, and the relay works. When the timer ends, the relay stops working, the time returns to the setting, and the next trigger signal is waited.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eInstructions\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cul data-mce-fragment=\"1\"\u003e\n\u003cli data-mce-fragment=\"1\"\u003e1).Press K1 to enter the time setting, the hundred digit digital tube starts to flash; press K2 at this time, the hundred digits change; press K1 again, the ten digital tube starts to flash; press K2 at this time, the ten digits change; press again After K1, the digital tube starts to flash. At this time, press K2, the digit of the digit changes; press K1 again to exit the setting, and the digital tube no longer flashes.\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003e2).When the digital tube is normally displayed, press K2, the decimal point is shifted, the decimal point is 0 to 999 seconds in ones digit, the decimal point is 0 to 99.9 seconds in ten digits, and the decimal point is 0 to 999 minutes; the time is set.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e2.Digital Display Delay Controller:(DC 12V 3 Button)\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eProduct parameters\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eWorking voltage: DC12V (normal working voltage DC10V-16V)\u003cbr data-mce-fragment=\"1\"\u003eSource: DC4V~20V (usual power supply positive trigger, button, PNP sensor, PLC signal, etc.)\u003cbr data-mce-fragment=\"1\"\u003eOutput capability: It can control devices within 30v5A or within 220v5A\u003cbr data-mce-fragment=\"1\"\u003eQuiescent current: 20mA, working current: 50mA\u003cbr data-mce-fragment=\"1\"\u003eService life: more than 100,000 times;\u003cbr data-mce-fragment=\"1\"\u003eWorking temperature: -40~85 °C;\u003cbr data-mce-fragment=\"1\"\u003eNet weight: about 26g\u003cbr data-mce-fragment=\"1\"\u003eSize: 64.2mm*34.8mm*18.5mm\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eFeatures\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eVoltage input anti-reverse circuit, worry-free wiring. Signal input optocoupler isolation, strong anti-interference ability. Set the parameter to power off permanent memory. Powerful flash MCU online programming function, according to user needs can contact the manufacturer to customize the required functions.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eWiring diagram\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cimg src=\"https:\/\/pg-cdn-a2.datacaciques.com\/00\/NDAy\/19\/08\/21\/02s76nl1201bce4t\/76050b0dfcc5297c.jpg\" data-mce-fragment=\"1\" data-mce-src=\"https:\/\/pg-cdn-a2.datacaciques.com\/00\/NDAy\/19\/08\/21\/02s76nl1201bce4t\/76050b0dfcc5297c.jpg\"\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eFunction introduction\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eP-1: The signal triggers the relay to pull in. When the time is up, the relay is disconnected during the delay.\u003cbr data-mce-fragment=\"1\"\u003eA: Invalid trigger again B: Re-trigger re-clocking C: Trigger relay reset again to stop timing\u003cbr data-mce-fragment=\"1\"\u003eP-2: The signal trigger start timing time T1, the time is up to the relay pull-in time T2 is disconnected (reset)\u003cbr data-mce-fragment=\"1\"\u003eA: Invalid trigger again B: Re-trigger re-clocking C: Start delay without triggering power-on\u003cbr data-mce-fragment=\"1\"\u003eP-3: Cycling: Turn on T1, disconnect T2, infinite loop. For T1 and T2, the time is adjustable; if a parameter is turned ON or OFF, it can be turned on or the power is turned on.\u003cbr data-mce-fragment=\"1\"\u003eA: The relay is turned on immediately after power-on. B: The relay is turned off and then turned on after power-on.\u003cbr data-mce-fragment=\"1\"\u003eP-4: There is signal, the relay is closed, the suction is kept, the signal disappears, the timing starts, the time is up, the relay is disconnected, during the delay, the signal is given again, the delay is cancelled, the relay is kept, the signal disappears, and the time is re-timed.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cstrong data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eNotes\u003c\/span\u003e\u003c\/strong\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eThe relay output is a passive contact that has no live output and controls the on\/off of a line.\u003c\/span\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e\u003cspan face=\"helveticao\" data-mce-fragment=\"1\"\u003e3.Digital Display Delay Controller:(DC 12V with Buzzer 3 Button)\u003c\/span\u003e\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan face=\"helveticao\" data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eProduct parameters\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eWorking voltage: DC12V (normal working voltage DC10V-16V)\u003cbr data-mce-fragment=\"1\"\u003eSource: DC4V~20V (usual power supply positive trigger, button, PNP sensor, PLC signal, etc.)\u003cbr data-mce-fragment=\"1\"\u003eOutput capability: It can control devices within 30v5A or within 220v5A\u003cbr data-mce-fragment=\"1\"\u003eQuiescent current: 20mA, working current: 50mA\u003cbr data-mce-fragment=\"1\"\u003eService life: more than 100,000 times;\u003cbr data-mce-fragment=\"1\"\u003eWorking temperature: -40~85 °C;\u003cbr data-mce-fragment=\"1\"\u003eNet weight: about 26g\u003cbr data-mce-fragment=\"1\"\u003eSize: 64.2mm*34.8mm*18.5mm\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eFeatures\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003ePower input flash-coupled, strong-interference ability. Power of flash MCU online programming function, according to user needs can contact the manufacturer to customize the Required functions.\u003c\/span\u003e\u003cspan face=\"helveticao\" data-mce-fragment=\"1\"\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003c\/span\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003eFunction introduction\u003cbr data-mce-fragment=\"1\"\u003eP-1: The trigger signal is received, the relay is turned on, the timer expires, and the relay is turned off.\u003cbr data-mce-fragment=\"1\"\u003eA1: Invalid again during delayed trigger\u003cbr data-mce-fragment=\"1\"\u003eA2: Trigger again during retiming delay\u003cbr data-mce-fragment=\"1\"\u003eA3: During the delay trigger, the trigger signal is received again to terminate the current delay.\u003cbr data-mce-fragment=\"1\"\u003eP-2: Receive trigger signal, X start time, relay off, Y start time, relay open\u003cbr data-mce-fragment=\"1\"\u003eP-3: Cycle switching mode\u003cbr data-mce-fragment=\"1\"\u003eA1: After the power relay is turned on, the timing is turned off and the loop is infinite.\u003cbr data-mce-fragment=\"1\"\u003eA2: After the power relay is turned off, the timing ends and the loop is infinite.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cstrong data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eNotes:\u003c\/span\u003e\u003c\/strong\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eThe relay output is a passive contact that has no live output and controls the on\/off of a line.\u003c\/span\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e4.Dual MOS delay control board: (DC 5-30V 4 Button)\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eDescription:\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003eDual MOS parallel active output, lower internal resistance, larger current, strong power interface, clear and simple, powerful, one-button emergency stop function (STOP button), with reverse connection protection, reverse connection, no burning, power-off memory. Increase Sleep mode, after enabling, no operation within 5 minutes, automatically turn off the display, wake up any button! You can set different OP, CL, LOP parameters, these parameters are independent of each other, save the setting parameters automatically power-down save and other functions, Almost all the needs!\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eProduct manual\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eWorking voltage: DC5V-DC30V (wide voltage anti-connection protection)\u003cbr data-mce-fragment=\"1\"\u003eTrigger signal source: high-level trigger DC 3.0V—24V signal ground and system ground to improve the system's anti-interference ability can also short-circuit the ground\u003cbr data-mce-fragment=\"1\"\u003eOutput capacity: DC DC 5V--36V, continuous current 15A at normal temperature, power 400W! Under the condition of auxiliary heat dissipation, the maximum current can reach 30A\u003cbr data-mce-fragment=\"1\"\u003eProduct size: 64mm*35mm*19.3mm\u003cbr data-mce-fragment=\"1\"\u003eMounting hole: diameter 3mm\u003cbr data-mce-fragment=\"1\"\u003eWorking temperature: -40 ° C ~ 85 ° C\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eOperating mode\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eP1 mode: After the signal is triggered, the MOS transistor turns on the OP time and then turns off; in the OP time, the following operation\u003cbr data-mce-fragment=\"1\"\u003eP1.1: The signal is triggered again.\u003cbr data-mce-fragment=\"1\"\u003eP1.2: Signal triggers re-timed again\u003cbr data-mce-fragment=\"1\"\u003eP1.3: The signal triggers reset again, the MOS tube is disconnected, and the timing is stopped.\u003cbr data-mce-fragment=\"1\"\u003eP-2: Give the trigger signal, after the MOS transistor is disconnected from the CL time, the MOS transistor turns on the OP time. After the timing is completed, the MOS transistor is disconnected.\u003cbr data-mce-fragment=\"1\"\u003eP3.1: Give the trigger signal, after the MOS transistor turns on the OP time, the MOS tube turns off the CL time, then loops the above action, the signal is given again in the loop, the MOS tube is disconnected, the timing is stopped; the number of cycles (LOP) can be set.\u003cbr data-mce-fragment=\"1\"\u003eP3.2: No need to trigger signal after power-on, MOS tube turns on OP time, MOS tube disconnects CL time, loops the above action; loop number (LOP) can be set\u003cbr data-mce-fragment=\"1\"\u003eP-4: Signal hold function If there is a trigger signal, the timing is cleared, the MOS transistor remains on; when the signal disappears, the MOS transistor is disconnected after timing the OP; during the timing, there is a signal and the timing is cleared.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eRelay enable mode\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eON : MOS tube is allowed to conduct during OP conduction time\u003cbr data-mce-fragment=\"1\"\u003eOFF : MOS tube is disabled, always off\u003cbr data-mce-fragment=\"1\"\u003eShort press the STOP button on the main interface to switch between ON and OFF. The current state will flash, then return to the main interface. This function is the emergency stop function. One button is used to open and close the MOS tube.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eSleep mode (long press the stop button to view the current mode)\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eC-P sleep mode: within five minutes, without any operation, the digital tube automatically turns off the display, the program runs normally.\u003cbr data-mce-fragment=\"1\"\u003eO-d normal mode: the digital tube is always on display\u003cbr data-mce-fragment=\"1\"\u003ePress and hold the STOP button for 2 seconds and then release to switch the C-P and O-d states. The current state will flash and then return to the main interface.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eTiming range\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eHow to choose the timing range\u003cbr data-mce-fragment=\"1\"\u003e1).After setting the parameter value in the mode selection interface, press the STOP button to select the timing range.\u003cbr data-mce-fragment=\"1\"\u003eXXX. Decimal point is in one place, timing range: 1 second to 999 seconds\u003cbr data-mce-fragment=\"1\"\u003eXX.X decimal point in ten, timing range: 0.1 seconds to 99.9 seconds\u003cbr data-mce-fragment=\"1\"\u003eX.X.X. The decimal point is fully illuminated, the timing range is from 1 minute to 999 minutes.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e2).For example, if you want to set the OP to 3.2 seconds, move the decimal point to ten digits, and the digital tube displays 03.2.\u003cbr data-mce-fragment=\"1\"\u003eParameter description: OP on time, CL off time, LOP cycle number 1-999 times, \"---\" stands for infinite loop.\u003cbr data-mce-fragment=\"1\"\u003eThese parameters are independent of each other, but each mode shares these parameters. For example, when the on-time OP is set to 5 seconds in P1.1, the user wants to switch to the P1.2 mode, then when entering the P1.2 setting corresponding parameters, the OP also It will be 5 seconds.\u003cbr data-mce-fragment=\"1\"\u003eDisplaying 000 on the main interface and pressing the SET button will display OPL, LOP and corresponding time XXX\u003cbr data-mce-fragment=\"1\"\u003eIf only OP in the mode, such as mode P1.1, P1.2, P1.3 time, then short press SET button will only display OP and corresponding time.\u003cbr data-mce-fragment=\"1\"\u003eIf the mode has OP, CL, LOP such as mode P3.1, P3.2 short press SET button will display OP and corresponding time, CL and corresponding time, LOP and corresponding times.\u003cbr data-mce-fragment=\"1\"\u003eAfter setting the mode, it is very convenient to easily check the parameters set in the current mode by pressing the SET button on the main interface.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eHow to set parameters\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e1) First determine the working mode of the MOS tube\u003cbr data-mce-fragment=\"1\"\u003eAccording to the working mode of the MOS tube, in the main interface (when the module is powered on, it will flash the current working mode (default P1.1 mode), then enter the main interface \"press and hold the SET button for 2 seconds and then release\" to enter the mode. Select the interface, press the UP, DOWN button to select the mode to be set P1.1~P-4\u003cbr data-mce-fragment=\"1\"\u003e2) After selecting the mode to be set (for example, P3.2), press the SET button to set the corresponding parameter. At this time, the parameter to be set will flash OP ON time, CL OFF time, LOP cycle number “---” Represents an infinite loop, adjusts the parameter value through UP and DOWN, supports long press (rapid increase or decrease) and short press (increase or decrease 1 unit); after setting the parameter value, select the decimal point position by short pressing the STOP button. , select the timing range (corresponding time 0.1 seconds ~ 999 minutes); short press the SET button to set the next parameter of the current mode, the process is the same as above.\u003cbr data-mce-fragment=\"1\"\u003e3) After setting the parameters of the selected mode, press and hold the SET button for 2 seconds to release, the currently set mode will flash, then return to the main interface and set the parameters successfully.\u003cbr data-mce-fragment=\"1\"\u003e4) Main interface: “000” (no decimal point) is displayed when the MOS tube is not working, and the MOS tube has a decimal point in the working state.\u003cbr data-mce-fragment=\"1\"\u003e5) Mode selection interface: long press SET button to enter, after setting is completed, long press SET button to exit, return to the main interface\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cstrong data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eNote:\u003c\/span\u003e\u003c\/strong\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eThe module is an active live output, and the voltage at the output (load) is equal to the input voltage DC\u003c\/span\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e5.USD Digital Display Delay Controller: ( DC12V 4 Button )\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eDescription:\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003eThis relay delay control board has a powerful and clear interface, powerful function, one-button emergency stop function (STOP button), with reverse connection protection, reverse connection without burning, power-off memory. Increased sleep mode, after enabling, No operation within 5 minutes, automatically turn off the display, wake up any button! You can set different OP, CL, LOP parameters, these parameters are independent of each other, save the setting parameters automatically power-down save and other functions, almost meet all needs!\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eProduct manual:\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eWorking voltage: DC6V-DC30V (wide voltage anti-connection protection)\u003cbr data-mce-fragment=\"1\"\u003eTrigger signal source: high-level trigger DC 3.0V—24V signal ground and system ground to improve the system's anti-interference ability can also short-circuit the ground\u003cbr data-mce-fragment=\"1\"\u003eOutput capacity: controllable DC 30V\/10A or AC 250V\/10A equipment\u003cbr data-mce-fragment=\"1\"\u003eProduct size: 64mm*35mm*19.3mm\u003cbr data-mce-fragment=\"1\"\u003eMounting hole: diameter 3mm\u003cbr data-mce-fragment=\"1\"\u003eWorking temperature: -40 ° C ~ 85 ° C\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e6.DC Motor Speed Controller :(DC 8-55V Motor Speed Controller )\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eDescription:\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003eThis product brings together a wide range of modern motor speed control, with the advantages of small size, simple operation, high current resistance and reverse connection. Suitable for most users in various environments with various speeds, support acceleration and deceleration functions can be set through the menu, with set parameters power off permanent memory function\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eProduct manual:\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eVoltage: DC8V-55V (wide voltage anti-back protection)\u003cbr data-mce-fragment=\"1\"\u003eSpeed range: long press \/ short press to adjust the degree, 0% -100% speed\u003cbr data-mce-fragment=\"1\"\u003eDrive current: up to 10A, (recommended output series 12A fuse)\u003cbr data-mce-fragment=\"1\"\u003eStandby current: \u0026lt;17mA\u003cbr data-mce-fragment=\"1\"\u003eMounting hole: diameter 3mm\u003cbr data-mce-fragment=\"1\"\u003eProduct size: 64mm*35mm*19mm (length * width * height)\u003cbr data-mce-fragment=\"1\"\u003eWorking temperature: -20 ° C ~ 70 ° C\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eInstructions:\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e1. Click\/long press the “speed increase” button to increase the motor speed to 100%.\u003cbr data-mce-fragment=\"1\"\u003e2. Click\/long press the “speed down” button to increase the motor speed to a minimum of 0%.\u003cbr data-mce-fragment=\"1\"\u003e3. Press and hold the “Power On\/Off” button for one second, the controller will be turned on or off (the power is turned off by default, and the memory function is activated after booting)\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003ePrecautions:\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e1. The digital tube flashes at the moment of power-on (normal phenomenon, no need to worry)\u003cbr data-mce-fragment=\"1\"\u003e2, close to the limit drive current working conditions, it is recommended to take the output end of the fuse\u003cbr data-mce-fragment=\"1\"\u003e3. The DC motor speed controller cannot be installed in places where there is dripping water and children can reach it.\u003cbr data-mce-fragment=\"1\"\u003e4. After wiring, check if the line is correct and then energize, so as to avoid accidentally burning the temperature controller and load device.\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003eWiring:\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e“M+” and “M-” are respectively connected to the positive and negative terminals of the output, M+ is positive and M- is negative.\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e“VIN” and “GND” are respectively connected to the positive and negative terminals of the input terminal, Vin is positive and GND is negative (input power supply voltage is DC8V-55V)\u003c\/span\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e7.Temperature Controller:(DC 12V Temperrature Controller)\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eProduct Parameters:\u003c\/span\u003e\u003c\/strong\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003eControl range: -50~110°C\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eResolution: -9.9~99.9, 0.1°C, other temperature range, 1°C\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eTemperature measurement accuracy: 0.1 °C\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eControl accuracy: 0.1 ° C\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eHysteresis accuracy: 0.1 ° C\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eRefresh rate: 0.5S\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eHigh temperature alarm: 0-110 °C\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eMeasurement input: NTC (10K0.5%) waterproof sensor\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eOutput: One way 10A relay\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eEnvironmental requirements: Temperature -10~60°C Humidity 20%-85%\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eSize: 48*40mm\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003ePower consumption of the whole machine: quiescent current: ≤35MA, Pull-in current: ≤65MA\u003c\/span\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eSetting Parameter Method:\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eOnce the power supply and load are connected, the control can be powered. After power-on, the digital tube displays the current real-time temperature. Press the SET button briefly, the digital tube displays the temperature flashing, press the + - button to adjust the set temperature; after the adjustment is completed, press the SET button to save the set temperature and return. At this time, the controller automatically Execute the relay on and off; press and hold the SET button for 5 seconds to enter the menu parameter setting, short press the + - button to switch P0...P6, short press the SET button to enter the menu.\u003cbr data-mce-fragment=\"1\"\u003eThe thermostat output is a 10A relay to meet a variety of high power loads, please ensure that the line is correct.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eIndicator light, digital tube status description:\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eIndicator light: Off means the relay is off, steady light means the relay is closed\u003cbr data-mce-fragment=\"1\"\u003eDigital tube: Display LLL for sensor open circuit: Display HHH is out of measurement range. The thermostat will forcibly open the relay.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eParameter Function Description:\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003ctable data-mce-fragment=\"1\"\u003e\n\u003ctbody data-mce-fragment=\"1\"\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eMenu identifier\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eMenu function\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003ePredetermined area\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eFactory setting\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eP0\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eRefrigeration C \/ Heating H\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eC\/H\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eC\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eP1\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eBacklash\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e0.1-15\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e2.0\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eP2\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eMaximum set temperature\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e-50~110℃\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e110\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eP3\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eMinimum set temperature\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e-50~110℃\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e-50\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eP4\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eTemperature correction\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e-7.0~7.0℃\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e0.0\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eP5\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003ePress delay\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e0-10 minutes\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e0\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eP6\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eHigh temperature alarm\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eON\/OFF\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003eOFF\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003ePackage Included:\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e1PC*DC 12V 2\/3\/4 Button Time Delay Relay Motor Speed Temperrature Controller+Buzzer\u003cstrong data-mce-fragment=\"1\"\u003e(According to your choice)\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e","published_at":"2020-11-17T14:10:21+08:00","created_at":"2020-11-17T14:10:20+08:00","vendor":"DIYMORE","type":"","tags":[],"price":899,"price_min":899,"price_max":899,"available":true,"price_varies":false,"compare_at_price":null,"compare_at_price_min":0,"compare_at_price_max":0,"compare_at_price_varies":false,"variants":[{"id":37539263873224,"title":"DC 8-55V Motor Speed Controller","option1":"DC 8-55V Motor Speed Controller","option2":null,"option3":null,"sku":"100040","requires_shipping":true,"taxable":false,"featured_image":null,"available":true,"name":"5V\/12V 2\/3\/4 Button Timer Delay Relay Motor Speed Temperature Controller+Buzzer - DC 8-55V Motor Speed Controller","public_title":"DC 8-55V Motor Speed Controller","options":["DC 8-55V Motor Speed Controller"],"price":899,"weight":0,"compare_at_price":null,"inventory_management":"shopify","barcode":"","requires_selling_plan":false,"selling_plan_allocations":[]}],"images":["\/\/www.diymore.cc\/cdn\/shop\/products\/100040_1.jpg?v=1605593426","\/\/www.diymore.cc\/cdn\/shop\/products\/100040_2.jpg?v=1605593426","\/\/www.diymore.cc\/cdn\/shop\/products\/100040.jpg?v=1605593426","\/\/www.diymore.cc\/cdn\/shop\/products\/100040_8.jpg?v=1605593426","\/\/www.diymore.cc\/cdn\/shop\/products\/100040_867e837f-1764-4e74-953c-5a0322a10abe.jpg?v=1605593426","\/\/www.diymore.cc\/cdn\/shop\/products\/100040_7.jpg?v=1605593426","\/\/www.diymore.cc\/cdn\/shop\/products\/100040_4.jpg?v=1605593426","\/\/www.diymore.cc\/cdn\/shop\/products\/100040_5.jpg?v=1605593427","\/\/www.diymore.cc\/cdn\/shop\/products\/100040_6.jpg?v=1605593427","\/\/www.diymore.cc\/cdn\/shop\/products\/100040_3.jpg?v=1605593427"],"featured_image":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040_1.jpg?v=1605593426","options":["Size"],"media":[{"alt":null,"id":14960171581640,"position":1,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040_1.jpg?v=1605593426"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040_1.jpg?v=1605593426","width":1000},{"alt":null,"id":14960171614408,"position":2,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040_2.jpg?v=1605593426"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040_2.jpg?v=1605593426","width":1000},{"alt":null,"id":14960171647176,"position":3,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040.jpg?v=1605593426"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040.jpg?v=1605593426","width":1000},{"alt":null,"id":14960171679944,"position":4,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040_8.jpg?v=1605593426"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040_8.jpg?v=1605593426","width":1000},{"alt":null,"id":14960171712712,"position":5,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040_867e837f-1764-4e74-953c-5a0322a10abe.jpg?v=1605593426"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040_867e837f-1764-4e74-953c-5a0322a10abe.jpg?v=1605593426","width":1000},{"alt":null,"id":14960171745480,"position":6,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040_7.jpg?v=1605593426"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040_7.jpg?v=1605593426","width":1000},{"alt":null,"id":14960171778248,"position":7,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040_4.jpg?v=1605593426"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040_4.jpg?v=1605593426","width":1000},{"alt":null,"id":14960171811016,"position":8,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040_5.jpg?v=1605593427"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040_5.jpg?v=1605593427","width":1000},{"alt":null,"id":14960171843784,"position":9,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040_6.jpg?v=1605593427"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040_6.jpg?v=1605593427","width":1000},{"alt":null,"id":14960171876552,"position":10,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040_3.jpg?v=1605593427"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040_3.jpg?v=1605593427","width":1000}],"requires_selling_plan":false,"selling_plan_groups":[],"content":"\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e1.Digital Display Delay Controller:(DC 12V with Buzzer 2 Button\u003cspan face=\"helveticao\" data-mce-fragment=\"1\"\u003e)\u003c\/span\u003e\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eProduct parameters\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\n\u003cul data-mce-fragment=\"1\"\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eWorking voltage: DC12V (normal working voltage DC10V-16V)\u003c\/span\u003e\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eSignal source: DC4V~20V (usual power supply positive trigger, button, PNP sensor, PLC signal, etc.)\u003c\/span\u003e\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eOutput capability: It can control devices within 30v5A or within 220v5A\u003c\/span\u003e\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eQuiescent current: 20mA, working current: 50mA\u003c\/span\u003e\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eService life: more than 100,000 times;\u003c\/span\u003e\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eWorking temperature: -40~85 °C;\u003c\/span\u003e\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eNet weight: about 26g\u003c\/span\u003e\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eSize: 64.2mm*34.8mm*18.5mm\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eFeatures\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\n\u003cul data-mce-fragment=\"1\"\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eVoltage input anti-reverse circuit, worry-free wiring. Signal input optocoupler isolation, strong anti-interference ability. Set the parameter to power off permanent memory. Powerful flash MCU online programming function, according to user needs can contact the manufacturer to customize the required functions.\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eFunction introduction\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\n\u003cul data-mce-fragment=\"1\"\u003e\n\u003cli data-mce-fragment=\"1\"\u003eWhen the power is turned on, the trigger signal is received, the countdown starts, and the relay works. When the timer ends, the relay stops working, the time returns to the setting, and the next trigger signal is waited.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eInstructions\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cul data-mce-fragment=\"1\"\u003e\n\u003cli data-mce-fragment=\"1\"\u003e1).Press K1 to enter the time setting, the hundred digit digital tube starts to flash; press K2 at this time, the hundred digits change; press K1 again, the ten digital tube starts to flash; press K2 at this time, the ten digits change; press again After K1, the digital tube starts to flash. At this time, press K2, the digit of the digit changes; press K1 again to exit the setting, and the digital tube no longer flashes.\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003e2).When the digital tube is normally displayed, press K2, the decimal point is shifted, the decimal point is 0 to 999 seconds in ones digit, the decimal point is 0 to 99.9 seconds in ten digits, and the decimal point is 0 to 999 minutes; the time is set.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e2.Digital Display Delay Controller:(DC 12V 3 Button)\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eProduct parameters\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eWorking voltage: DC12V (normal working voltage DC10V-16V)\u003cbr data-mce-fragment=\"1\"\u003eSource: DC4V~20V (usual power supply positive trigger, button, PNP sensor, PLC signal, etc.)\u003cbr data-mce-fragment=\"1\"\u003eOutput capability: It can control devices within 30v5A or within 220v5A\u003cbr data-mce-fragment=\"1\"\u003eQuiescent current: 20mA, working current: 50mA\u003cbr data-mce-fragment=\"1\"\u003eService life: more than 100,000 times;\u003cbr data-mce-fragment=\"1\"\u003eWorking temperature: -40~85 °C;\u003cbr data-mce-fragment=\"1\"\u003eNet weight: about 26g\u003cbr data-mce-fragment=\"1\"\u003eSize: 64.2mm*34.8mm*18.5mm\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eFeatures\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eVoltage input anti-reverse circuit, worry-free wiring. Signal input optocoupler isolation, strong anti-interference ability. Set the parameter to power off permanent memory. Powerful flash MCU online programming function, according to user needs can contact the manufacturer to customize the required functions.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eWiring diagram\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cimg src=\"https:\/\/pg-cdn-a2.datacaciques.com\/00\/NDAy\/19\/08\/21\/02s76nl1201bce4t\/76050b0dfcc5297c.jpg\" data-mce-fragment=\"1\" data-mce-src=\"https:\/\/pg-cdn-a2.datacaciques.com\/00\/NDAy\/19\/08\/21\/02s76nl1201bce4t\/76050b0dfcc5297c.jpg\"\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eFunction introduction\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eP-1: The signal triggers the relay to pull in. When the time is up, the relay is disconnected during the delay.\u003cbr data-mce-fragment=\"1\"\u003eA: Invalid trigger again B: Re-trigger re-clocking C: Trigger relay reset again to stop timing\u003cbr data-mce-fragment=\"1\"\u003eP-2: The signal trigger start timing time T1, the time is up to the relay pull-in time T2 is disconnected (reset)\u003cbr data-mce-fragment=\"1\"\u003eA: Invalid trigger again B: Re-trigger re-clocking C: Start delay without triggering power-on\u003cbr data-mce-fragment=\"1\"\u003eP-3: Cycling: Turn on T1, disconnect T2, infinite loop. For T1 and T2, the time is adjustable; if a parameter is turned ON or OFF, it can be turned on or the power is turned on.\u003cbr data-mce-fragment=\"1\"\u003eA: The relay is turned on immediately after power-on. B: The relay is turned off and then turned on after power-on.\u003cbr data-mce-fragment=\"1\"\u003eP-4: There is signal, the relay is closed, the suction is kept, the signal disappears, the timing starts, the time is up, the relay is disconnected, during the delay, the signal is given again, the delay is cancelled, the relay is kept, the signal disappears, and the time is re-timed.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cstrong data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eNotes\u003c\/span\u003e\u003c\/strong\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eThe relay output is a passive contact that has no live output and controls the on\/off of a line.\u003c\/span\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e\u003cspan face=\"helveticao\" data-mce-fragment=\"1\"\u003e3.Digital Display Delay Controller:(DC 12V with Buzzer 3 Button)\u003c\/span\u003e\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan face=\"helveticao\" data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eProduct parameters\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eWorking voltage: DC12V (normal working voltage DC10V-16V)\u003cbr data-mce-fragment=\"1\"\u003eSource: DC4V~20V (usual power supply positive trigger, button, PNP sensor, PLC signal, etc.)\u003cbr data-mce-fragment=\"1\"\u003eOutput capability: It can control devices within 30v5A or within 220v5A\u003cbr data-mce-fragment=\"1\"\u003eQuiescent current: 20mA, working current: 50mA\u003cbr data-mce-fragment=\"1\"\u003eService life: more than 100,000 times;\u003cbr data-mce-fragment=\"1\"\u003eWorking temperature: -40~85 °C;\u003cbr data-mce-fragment=\"1\"\u003eNet weight: about 26g\u003cbr data-mce-fragment=\"1\"\u003eSize: 64.2mm*34.8mm*18.5mm\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eFeatures\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003ePower input flash-coupled, strong-interference ability. Power of flash MCU online programming function, according to user needs can contact the manufacturer to customize the Required functions.\u003c\/span\u003e\u003cspan face=\"helveticao\" data-mce-fragment=\"1\"\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003c\/span\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003eFunction introduction\u003cbr data-mce-fragment=\"1\"\u003eP-1: The trigger signal is received, the relay is turned on, the timer expires, and the relay is turned off.\u003cbr data-mce-fragment=\"1\"\u003eA1: Invalid again during delayed trigger\u003cbr data-mce-fragment=\"1\"\u003eA2: Trigger again during retiming delay\u003cbr data-mce-fragment=\"1\"\u003eA3: During the delay trigger, the trigger signal is received again to terminate the current delay.\u003cbr data-mce-fragment=\"1\"\u003eP-2: Receive trigger signal, X start time, relay off, Y start time, relay open\u003cbr data-mce-fragment=\"1\"\u003eP-3: Cycle switching mode\u003cbr data-mce-fragment=\"1\"\u003eA1: After the power relay is turned on, the timing is turned off and the loop is infinite.\u003cbr data-mce-fragment=\"1\"\u003eA2: After the power relay is turned off, the timing ends and the loop is infinite.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cstrong data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eNotes:\u003c\/span\u003e\u003c\/strong\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eThe relay output is a passive contact that has no live output and controls the on\/off of a line.\u003c\/span\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e4.Dual MOS delay control board: (DC 5-30V 4 Button)\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eDescription:\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003eDual MOS parallel active output, lower internal resistance, larger current, strong power interface, clear and simple, powerful, one-button emergency stop function (STOP button), with reverse connection protection, reverse connection, no burning, power-off memory. Increase Sleep mode, after enabling, no operation within 5 minutes, automatically turn off the display, wake up any button! You can set different OP, CL, LOP parameters, these parameters are independent of each other, save the setting parameters automatically power-down save and other functions, Almost all the needs!\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eProduct manual\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eWorking voltage: DC5V-DC30V (wide voltage anti-connection protection)\u003cbr data-mce-fragment=\"1\"\u003eTrigger signal source: high-level trigger DC 3.0V—24V signal ground and system ground to improve the system's anti-interference ability can also short-circuit the ground\u003cbr data-mce-fragment=\"1\"\u003eOutput capacity: DC DC 5V--36V, continuous current 15A at normal temperature, power 400W! Under the condition of auxiliary heat dissipation, the maximum current can reach 30A\u003cbr data-mce-fragment=\"1\"\u003eProduct size: 64mm*35mm*19.3mm\u003cbr data-mce-fragment=\"1\"\u003eMounting hole: diameter 3mm\u003cbr data-mce-fragment=\"1\"\u003eWorking temperature: -40 ° C ~ 85 ° C\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eOperating mode\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eP1 mode: After the signal is triggered, the MOS transistor turns on the OP time and then turns off; in the OP time, the following operation\u003cbr data-mce-fragment=\"1\"\u003eP1.1: The signal is triggered again.\u003cbr data-mce-fragment=\"1\"\u003eP1.2: Signal triggers re-timed again\u003cbr data-mce-fragment=\"1\"\u003eP1.3: The signal triggers reset again, the MOS tube is disconnected, and the timing is stopped.\u003cbr data-mce-fragment=\"1\"\u003eP-2: Give the trigger signal, after the MOS transistor is disconnected from the CL time, the MOS transistor turns on the OP time. After the timing is completed, the MOS transistor is disconnected.\u003cbr data-mce-fragment=\"1\"\u003eP3.1: Give the trigger signal, after the MOS transistor turns on the OP time, the MOS tube turns off the CL time, then loops the above action, the signal is given again in the loop, the MOS tube is disconnected, the timing is stopped; the number of cycles (LOP) can be set.\u003cbr data-mce-fragment=\"1\"\u003eP3.2: No need to trigger signal after power-on, MOS tube turns on OP time, MOS tube disconnects CL time, loops the above action; loop number (LOP) can be set\u003cbr data-mce-fragment=\"1\"\u003eP-4: Signal hold function If there is a trigger signal, the timing is cleared, the MOS transistor remains on; when the signal disappears, the MOS transistor is disconnected after timing the OP; during the timing, there is a signal and the timing is cleared.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eRelay enable mode\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eON : MOS tube is allowed to conduct during OP conduction time\u003cbr data-mce-fragment=\"1\"\u003eOFF : MOS tube is disabled, always off\u003cbr data-mce-fragment=\"1\"\u003eShort press the STOP button on the main interface to switch between ON and OFF. The current state will flash, then return to the main interface. This function is the emergency stop function. One button is used to open and close the MOS tube.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eSleep mode (long press the stop button to view the current mode)\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eC-P sleep mode: within five minutes, without any operation, the digital tube automatically turns off the display, the program runs normally.\u003cbr data-mce-fragment=\"1\"\u003eO-d normal mode: the digital tube is always on display\u003cbr data-mce-fragment=\"1\"\u003ePress and hold the STOP button for 2 seconds and then release to switch the C-P and O-d states. The current state will flash and then return to the main interface.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eTiming range\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eHow to choose the timing range\u003cbr data-mce-fragment=\"1\"\u003e1).After setting the parameter value in the mode selection interface, press the STOP button to select the timing range.\u003cbr data-mce-fragment=\"1\"\u003eXXX. Decimal point is in one place, timing range: 1 second to 999 seconds\u003cbr data-mce-fragment=\"1\"\u003eXX.X decimal point in ten, timing range: 0.1 seconds to 99.9 seconds\u003cbr data-mce-fragment=\"1\"\u003eX.X.X. The decimal point is fully illuminated, the timing range is from 1 minute to 999 minutes.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e2).For example, if you want to set the OP to 3.2 seconds, move the decimal point to ten digits, and the digital tube displays 03.2.\u003cbr data-mce-fragment=\"1\"\u003eParameter description: OP on time, CL off time, LOP cycle number 1-999 times, \"---\" stands for infinite loop.\u003cbr data-mce-fragment=\"1\"\u003eThese parameters are independent of each other, but each mode shares these parameters. For example, when the on-time OP is set to 5 seconds in P1.1, the user wants to switch to the P1.2 mode, then when entering the P1.2 setting corresponding parameters, the OP also It will be 5 seconds.\u003cbr data-mce-fragment=\"1\"\u003eDisplaying 000 on the main interface and pressing the SET button will display OPL, LOP and corresponding time XXX\u003cbr data-mce-fragment=\"1\"\u003eIf only OP in the mode, such as mode P1.1, P1.2, P1.3 time, then short press SET button will only display OP and corresponding time.\u003cbr data-mce-fragment=\"1\"\u003eIf the mode has OP, CL, LOP such as mode P3.1, P3.2 short press SET button will display OP and corresponding time, CL and corresponding time, LOP and corresponding times.\u003cbr data-mce-fragment=\"1\"\u003eAfter setting the mode, it is very convenient to easily check the parameters set in the current mode by pressing the SET button on the main interface.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eHow to set parameters\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e1) First determine the working mode of the MOS tube\u003cbr data-mce-fragment=\"1\"\u003eAccording to the working mode of the MOS tube, in the main interface (when the module is powered on, it will flash the current working mode (default P1.1 mode), then enter the main interface \"press and hold the SET button for 2 seconds and then release\" to enter the mode. Select the interface, press the UP, DOWN button to select the mode to be set P1.1~P-4\u003cbr data-mce-fragment=\"1\"\u003e2) After selecting the mode to be set (for example, P3.2), press the SET button to set the corresponding parameter. At this time, the parameter to be set will flash OP ON time, CL OFF time, LOP cycle number “---” Represents an infinite loop, adjusts the parameter value through UP and DOWN, supports long press (rapid increase or decrease) and short press (increase or decrease 1 unit); after setting the parameter value, select the decimal point position by short pressing the STOP button. , select the timing range (corresponding time 0.1 seconds ~ 999 minutes); short press the SET button to set the next parameter of the current mode, the process is the same as above.\u003cbr data-mce-fragment=\"1\"\u003e3) After setting the parameters of the selected mode, press and hold the SET button for 2 seconds to release, the currently set mode will flash, then return to the main interface and set the parameters successfully.\u003cbr data-mce-fragment=\"1\"\u003e4) Main interface: “000” (no decimal point) is displayed when the MOS tube is not working, and the MOS tube has a decimal point in the working state.\u003cbr data-mce-fragment=\"1\"\u003e5) Mode selection interface: long press SET button to enter, after setting is completed, long press SET button to exit, return to the main interface\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cstrong data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eNote:\u003c\/span\u003e\u003c\/strong\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eThe module is an active live output, and the voltage at the output (load) is equal to the input voltage DC\u003c\/span\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e5.USD Digital Display Delay Controller: ( DC12V 4 Button )\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eDescription:\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003eThis relay delay control board has a powerful and clear interface, powerful function, one-button emergency stop function (STOP button), with reverse connection protection, reverse connection without burning, power-off memory. Increased sleep mode, after enabling, No operation within 5 minutes, automatically turn off the display, wake up any button! You can set different OP, CL, LOP parameters, these parameters are independent of each other, save the setting parameters automatically power-down save and other functions, almost meet all needs!\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eProduct manual:\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eWorking voltage: DC6V-DC30V (wide voltage anti-connection protection)\u003cbr data-mce-fragment=\"1\"\u003eTrigger signal source: high-level trigger DC 3.0V—24V signal ground and system ground to improve the system's anti-interference ability can also short-circuit the ground\u003cbr data-mce-fragment=\"1\"\u003eOutput capacity: controllable DC 30V\/10A or AC 250V\/10A equipment\u003cbr data-mce-fragment=\"1\"\u003eProduct size: 64mm*35mm*19.3mm\u003cbr data-mce-fragment=\"1\"\u003eMounting hole: diameter 3mm\u003cbr data-mce-fragment=\"1\"\u003eWorking temperature: -40 ° C ~ 85 ° C\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e6.DC Motor Speed Controller :(DC 8-55V Motor Speed Controller )\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eDescription:\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003eThis product brings together a wide range of modern motor speed control, with the advantages of small size, simple operation, high current resistance and reverse connection. Suitable for most users in various environments with various speeds, support acceleration and deceleration functions can be set through the menu, with set parameters power off permanent memory function\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eProduct manual:\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eVoltage: DC8V-55V (wide voltage anti-back protection)\u003cbr data-mce-fragment=\"1\"\u003eSpeed range: long press \/ short press to adjust the degree, 0% -100% speed\u003cbr data-mce-fragment=\"1\"\u003eDrive current: up to 10A, (recommended output series 12A fuse)\u003cbr data-mce-fragment=\"1\"\u003eStandby current: \u0026lt;17mA\u003cbr data-mce-fragment=\"1\"\u003eMounting hole: diameter 3mm\u003cbr data-mce-fragment=\"1\"\u003eProduct size: 64mm*35mm*19mm (length * width * height)\u003cbr data-mce-fragment=\"1\"\u003eWorking temperature: -20 ° C ~ 70 ° C\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eInstructions:\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e1. Click\/long press the “speed increase” button to increase the motor speed to 100%.\u003cbr data-mce-fragment=\"1\"\u003e2. Click\/long press the “speed down” button to increase the motor speed to a minimum of 0%.\u003cbr data-mce-fragment=\"1\"\u003e3. Press and hold the “Power On\/Off” button for one second, the controller will be turned on or off (the power is turned off by default, and the memory function is activated after booting)\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003ePrecautions:\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e1. The digital tube flashes at the moment of power-on (normal phenomenon, no need to worry)\u003cbr data-mce-fragment=\"1\"\u003e2, close to the limit drive current working conditions, it is recommended to take the output end of the fuse\u003cbr data-mce-fragment=\"1\"\u003e3. The DC motor speed controller cannot be installed in places where there is dripping water and children can reach it.\u003cbr data-mce-fragment=\"1\"\u003e4. After wiring, check if the line is correct and then energize, so as to avoid accidentally burning the temperature controller and load device.\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003eWiring:\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e“M+” and “M-” are respectively connected to the positive and negative terminals of the output, M+ is positive and M- is negative.\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e“VIN” and “GND” are respectively connected to the positive and negative terminals of the input terminal, Vin is positive and GND is negative (input power supply voltage is DC8V-55V)\u003c\/span\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e7.Temperature Controller:(DC 12V Temperrature Controller)\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eProduct Parameters:\u003c\/span\u003e\u003c\/strong\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003eControl range: -50~110°C\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eResolution: -9.9~99.9, 0.1°C, other temperature range, 1°C\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eTemperature measurement accuracy: 0.1 °C\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eControl accuracy: 0.1 ° C\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eHysteresis accuracy: 0.1 ° C\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eRefresh rate: 0.5S\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eHigh temperature alarm: 0-110 °C\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eMeasurement input: NTC (10K0.5%) waterproof sensor\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eOutput: One way 10A relay\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eEnvironmental requirements: Temperature -10~60°C Humidity 20%-85%\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eSize: 48*40mm\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003ePower consumption of the whole machine: quiescent current: ≤35MA, Pull-in current: ≤65MA\u003c\/span\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eSetting Parameter Method:\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eOnce the power supply and load are connected, the control can be powered. After power-on, the digital tube displays the current real-time temperature. Press the SET button briefly, the digital tube displays the temperature flashing, press the + - button to adjust the set temperature; after the adjustment is completed, press the SET button to save the set temperature and return. At this time, the controller automatically Execute the relay on and off; press and hold the SET button for 5 seconds to enter the menu parameter setting, short press the + - button to switch P0...P6, short press the SET button to enter the menu.\u003cbr data-mce-fragment=\"1\"\u003eThe thermostat output is a 10A relay to meet a variety of high power loads, please ensure that the line is correct.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eIndicator light, digital tube status description:\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eIndicator light: Off means the relay is off, steady light means the relay is closed\u003cbr data-mce-fragment=\"1\"\u003eDigital tube: Display LLL for sensor open circuit: Display HHH is out of measurement range. The thermostat will forcibly open the relay.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eParameter Function Description:\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003ctable data-mce-fragment=\"1\"\u003e\n\u003ctbody data-mce-fragment=\"1\"\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eMenu identifier\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eMenu function\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003ePredetermined area\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eFactory setting\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eP0\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eRefrigeration C \/ Heating H\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eC\/H\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eC\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eP1\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eBacklash\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e0.1-15\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e2.0\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eP2\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eMaximum set temperature\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e-50~110℃\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e110\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eP3\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eMinimum set temperature\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e-50~110℃\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e-50\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eP4\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eTemperature correction\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e-7.0~7.0℃\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e0.0\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eP5\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003ePress delay\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e0-10 minutes\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e0\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eP6\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eHigh temperature alarm\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eON\/OFF\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003eOFF\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003ePackage Included:\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e1PC*DC 12V 2\/3\/4 Button Time Delay Relay Motor Speed Temperrature Controller+Buzzer\u003cstrong data-mce-fragment=\"1\"\u003e(According to your choice)\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e"}
-
Translation missing: en.products.product.regular_price $9.99{"id":6086411911368,"title":"5V\/12V 2\/3\/4 Button Timer Delay Relay Motor Speed Temperature Controller+Buzzer","handle":"5v-12v-2-3-4-button-timer-delay-relay-motor-speed-temperature-controller-buzzer","description":"\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e1.Digital Display Delay Controller:(DC 12V with Buzzer 2 Button\u003cspan face=\"helveticao\" data-mce-fragment=\"1\"\u003e)\u003c\/span\u003e\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eProduct parameters\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\n\u003cul data-mce-fragment=\"1\"\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eWorking voltage: DC12V (normal working voltage DC10V-16V)\u003c\/span\u003e\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eSignal source: DC4V~20V (usual power supply positive trigger, button, PNP sensor, PLC signal, etc.)\u003c\/span\u003e\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eOutput capability: It can control devices within 30v5A or within 220v5A\u003c\/span\u003e\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eQuiescent current: 20mA, working current: 50mA\u003c\/span\u003e\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eService life: more than 100,000 times;\u003c\/span\u003e\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eWorking temperature: -40~85 °C;\u003c\/span\u003e\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eNet weight: about 26g\u003c\/span\u003e\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eSize: 64.2mm*34.8mm*18.5mm\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eFeatures\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\n\u003cul data-mce-fragment=\"1\"\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eVoltage input anti-reverse circuit, worry-free wiring. Signal input optocoupler isolation, strong anti-interference ability. Set the parameter to power off permanent memory. Powerful flash MCU online programming function, according to user needs can contact the manufacturer to customize the required functions.\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eFunction introduction\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\n\u003cul data-mce-fragment=\"1\"\u003e\n\u003cli data-mce-fragment=\"1\"\u003eWhen the power is turned on, the trigger signal is received, the countdown starts, and the relay works. When the timer ends, the relay stops working, the time returns to the setting, and the next trigger signal is waited.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eInstructions\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cul data-mce-fragment=\"1\"\u003e\n\u003cli data-mce-fragment=\"1\"\u003e1).Press K1 to enter the time setting, the hundred digit digital tube starts to flash; press K2 at this time, the hundred digits change; press K1 again, the ten digital tube starts to flash; press K2 at this time, the ten digits change; press again After K1, the digital tube starts to flash. At this time, press K2, the digit of the digit changes; press K1 again to exit the setting, and the digital tube no longer flashes.\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003e2).When the digital tube is normally displayed, press K2, the decimal point is shifted, the decimal point is 0 to 999 seconds in ones digit, the decimal point is 0 to 99.9 seconds in ten digits, and the decimal point is 0 to 999 minutes; the time is set.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e2.Digital Display Delay Controller:(DC 12V 3 Button)\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eProduct parameters\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eWorking voltage: DC12V (normal working voltage DC10V-16V)\u003cbr data-mce-fragment=\"1\"\u003eSource: DC4V~20V (usual power supply positive trigger, button, PNP sensor, PLC signal, etc.)\u003cbr data-mce-fragment=\"1\"\u003eOutput capability: It can control devices within 30v5A or within 220v5A\u003cbr data-mce-fragment=\"1\"\u003eQuiescent current: 20mA, working current: 50mA\u003cbr data-mce-fragment=\"1\"\u003eService life: more than 100,000 times;\u003cbr data-mce-fragment=\"1\"\u003eWorking temperature: -40~85 °C;\u003cbr data-mce-fragment=\"1\"\u003eNet weight: about 26g\u003cbr data-mce-fragment=\"1\"\u003eSize: 64.2mm*34.8mm*18.5mm\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eFeatures\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eVoltage input anti-reverse circuit, worry-free wiring. Signal input optocoupler isolation, strong anti-interference ability. Set the parameter to power off permanent memory. Powerful flash MCU online programming function, according to user needs can contact the manufacturer to customize the required functions.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eWiring diagram\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cimg src=\"https:\/\/pg-cdn-a2.datacaciques.com\/00\/NDAy\/19\/08\/21\/02s76nl1201bce4t\/76050b0dfcc5297c.jpg\" data-mce-fragment=\"1\" data-mce-src=\"https:\/\/pg-cdn-a2.datacaciques.com\/00\/NDAy\/19\/08\/21\/02s76nl1201bce4t\/76050b0dfcc5297c.jpg\"\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eFunction introduction\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eP-1: The signal triggers the relay to pull in. When the time is up, the relay is disconnected during the delay.\u003cbr data-mce-fragment=\"1\"\u003eA: Invalid trigger again B: Re-trigger re-clocking C: Trigger relay reset again to stop timing\u003cbr data-mce-fragment=\"1\"\u003eP-2: The signal trigger start timing time T1, the time is up to the relay pull-in time T2 is disconnected (reset)\u003cbr data-mce-fragment=\"1\"\u003eA: Invalid trigger again B: Re-trigger re-clocking C: Start delay without triggering power-on\u003cbr data-mce-fragment=\"1\"\u003eP-3: Cycling: Turn on T1, disconnect T2, infinite loop. For T1 and T2, the time is adjustable; if a parameter is turned ON or OFF, it can be turned on or the power is turned on.\u003cbr data-mce-fragment=\"1\"\u003eA: The relay is turned on immediately after power-on. B: The relay is turned off and then turned on after power-on.\u003cbr data-mce-fragment=\"1\"\u003eP-4: There is signal, the relay is closed, the suction is kept, the signal disappears, the timing starts, the time is up, the relay is disconnected, during the delay, the signal is given again, the delay is cancelled, the relay is kept, the signal disappears, and the time is re-timed.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cstrong data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eNotes\u003c\/span\u003e\u003c\/strong\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eThe relay output is a passive contact that has no live output and controls the on\/off of a line.\u003c\/span\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e\u003cspan face=\"helveticao\" data-mce-fragment=\"1\"\u003e3.Digital Display Delay Controller:(DC 12V with Buzzer 3 Button)\u003c\/span\u003e\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan face=\"helveticao\" data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eProduct parameters\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eWorking voltage: DC12V (normal working voltage DC10V-16V)\u003cbr data-mce-fragment=\"1\"\u003eSource: DC4V~20V (usual power supply positive trigger, button, PNP sensor, PLC signal, etc.)\u003cbr data-mce-fragment=\"1\"\u003eOutput capability: It can control devices within 30v5A or within 220v5A\u003cbr data-mce-fragment=\"1\"\u003eQuiescent current: 20mA, working current: 50mA\u003cbr data-mce-fragment=\"1\"\u003eService life: more than 100,000 times;\u003cbr data-mce-fragment=\"1\"\u003eWorking temperature: -40~85 °C;\u003cbr data-mce-fragment=\"1\"\u003eNet weight: about 26g\u003cbr data-mce-fragment=\"1\"\u003eSize: 64.2mm*34.8mm*18.5mm\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eFeatures\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003ePower input flash-coupled, strong-interference ability. Power of flash MCU online programming function, according to user needs can contact the manufacturer to customize the Required functions.\u003c\/span\u003e\u003cspan face=\"helveticao\" data-mce-fragment=\"1\"\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003c\/span\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003eFunction introduction\u003cbr data-mce-fragment=\"1\"\u003eP-1: The trigger signal is received, the relay is turned on, the timer expires, and the relay is turned off.\u003cbr data-mce-fragment=\"1\"\u003eA1: Invalid again during delayed trigger\u003cbr data-mce-fragment=\"1\"\u003eA2: Trigger again during retiming delay\u003cbr data-mce-fragment=\"1\"\u003eA3: During the delay trigger, the trigger signal is received again to terminate the current delay.\u003cbr data-mce-fragment=\"1\"\u003eP-2: Receive trigger signal, X start time, relay off, Y start time, relay open\u003cbr data-mce-fragment=\"1\"\u003eP-3: Cycle switching mode\u003cbr data-mce-fragment=\"1\"\u003eA1: After the power relay is turned on, the timing is turned off and the loop is infinite.\u003cbr data-mce-fragment=\"1\"\u003eA2: After the power relay is turned off, the timing ends and the loop is infinite.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cstrong data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eNotes:\u003c\/span\u003e\u003c\/strong\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eThe relay output is a passive contact that has no live output and controls the on\/off of a line.\u003c\/span\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e4.Dual MOS delay control board: (DC 5-30V 4 Button)\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eDescription:\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003eDual MOS parallel active output, lower internal resistance, larger current, strong power interface, clear and simple, powerful, one-button emergency stop function (STOP button), with reverse connection protection, reverse connection, no burning, power-off memory. Increase Sleep mode, after enabling, no operation within 5 minutes, automatically turn off the display, wake up any button! You can set different OP, CL, LOP parameters, these parameters are independent of each other, save the setting parameters automatically power-down save and other functions, Almost all the needs!\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eProduct manual\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eWorking voltage: DC5V-DC30V (wide voltage anti-connection protection)\u003cbr data-mce-fragment=\"1\"\u003eTrigger signal source: high-level trigger DC 3.0V—24V signal ground and system ground to improve the system's anti-interference ability can also short-circuit the ground\u003cbr data-mce-fragment=\"1\"\u003eOutput capacity: DC DC 5V--36V, continuous current 15A at normal temperature, power 400W! Under the condition of auxiliary heat dissipation, the maximum current can reach 30A\u003cbr data-mce-fragment=\"1\"\u003eProduct size: 64mm*35mm*19.3mm\u003cbr data-mce-fragment=\"1\"\u003eMounting hole: diameter 3mm\u003cbr data-mce-fragment=\"1\"\u003eWorking temperature: -40 ° C ~ 85 ° C\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eOperating mode\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eP1 mode: After the signal is triggered, the MOS transistor turns on the OP time and then turns off; in the OP time, the following operation\u003cbr data-mce-fragment=\"1\"\u003eP1.1: The signal is triggered again.\u003cbr data-mce-fragment=\"1\"\u003eP1.2: Signal triggers re-timed again\u003cbr data-mce-fragment=\"1\"\u003eP1.3: The signal triggers reset again, the MOS tube is disconnected, and the timing is stopped.\u003cbr data-mce-fragment=\"1\"\u003eP-2: Give the trigger signal, after the MOS transistor is disconnected from the CL time, the MOS transistor turns on the OP time. After the timing is completed, the MOS transistor is disconnected.\u003cbr data-mce-fragment=\"1\"\u003eP3.1: Give the trigger signal, after the MOS transistor turns on the OP time, the MOS tube turns off the CL time, then loops the above action, the signal is given again in the loop, the MOS tube is disconnected, the timing is stopped; the number of cycles (LOP) can be set.\u003cbr data-mce-fragment=\"1\"\u003eP3.2: No need to trigger signal after power-on, MOS tube turns on OP time, MOS tube disconnects CL time, loops the above action; loop number (LOP) can be set\u003cbr data-mce-fragment=\"1\"\u003eP-4: Signal hold function If there is a trigger signal, the timing is cleared, the MOS transistor remains on; when the signal disappears, the MOS transistor is disconnected after timing the OP; during the timing, there is a signal and the timing is cleared.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eRelay enable mode\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eON : MOS tube is allowed to conduct during OP conduction time\u003cbr data-mce-fragment=\"1\"\u003eOFF : MOS tube is disabled, always off\u003cbr data-mce-fragment=\"1\"\u003eShort press the STOP button on the main interface to switch between ON and OFF. The current state will flash, then return to the main interface. This function is the emergency stop function. One button is used to open and close the MOS tube.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eSleep mode (long press the stop button to view the current mode)\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eC-P sleep mode: within five minutes, without any operation, the digital tube automatically turns off the display, the program runs normally.\u003cbr data-mce-fragment=\"1\"\u003eO-d normal mode: the digital tube is always on display\u003cbr data-mce-fragment=\"1\"\u003ePress and hold the STOP button for 2 seconds and then release to switch the C-P and O-d states. The current state will flash and then return to the main interface.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eTiming range\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eHow to choose the timing range\u003cbr data-mce-fragment=\"1\"\u003e1).After setting the parameter value in the mode selection interface, press the STOP button to select the timing range.\u003cbr data-mce-fragment=\"1\"\u003eXXX. Decimal point is in one place, timing range: 1 second to 999 seconds\u003cbr data-mce-fragment=\"1\"\u003eXX.X decimal point in ten, timing range: 0.1 seconds to 99.9 seconds\u003cbr data-mce-fragment=\"1\"\u003eX.X.X. The decimal point is fully illuminated, the timing range is from 1 minute to 999 minutes.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e2).For example, if you want to set the OP to 3.2 seconds, move the decimal point to ten digits, and the digital tube displays 03.2.\u003cbr data-mce-fragment=\"1\"\u003eParameter description: OP on time, CL off time, LOP cycle number 1-999 times, \"---\" stands for infinite loop.\u003cbr data-mce-fragment=\"1\"\u003eThese parameters are independent of each other, but each mode shares these parameters. For example, when the on-time OP is set to 5 seconds in P1.1, the user wants to switch to the P1.2 mode, then when entering the P1.2 setting corresponding parameters, the OP also It will be 5 seconds.\u003cbr data-mce-fragment=\"1\"\u003eDisplaying 000 on the main interface and pressing the SET button will display OPL, LOP and corresponding time XXX\u003cbr data-mce-fragment=\"1\"\u003eIf only OP in the mode, such as mode P1.1, P1.2, P1.3 time, then short press SET button will only display OP and corresponding time.\u003cbr data-mce-fragment=\"1\"\u003eIf the mode has OP, CL, LOP such as mode P3.1, P3.2 short press SET button will display OP and corresponding time, CL and corresponding time, LOP and corresponding times.\u003cbr data-mce-fragment=\"1\"\u003eAfter setting the mode, it is very convenient to easily check the parameters set in the current mode by pressing the SET button on the main interface.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eHow to set parameters\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e1) First determine the working mode of the MOS tube\u003cbr data-mce-fragment=\"1\"\u003eAccording to the working mode of the MOS tube, in the main interface (when the module is powered on, it will flash the current working mode (default P1.1 mode), then enter the main interface \"press and hold the SET button for 2 seconds and then release\" to enter the mode. Select the interface, press the UP, DOWN button to select the mode to be set P1.1~P-4\u003cbr data-mce-fragment=\"1\"\u003e2) After selecting the mode to be set (for example, P3.2), press the SET button to set the corresponding parameter. At this time, the parameter to be set will flash OP ON time, CL OFF time, LOP cycle number “---” Represents an infinite loop, adjusts the parameter value through UP and DOWN, supports long press (rapid increase or decrease) and short press (increase or decrease 1 unit); after setting the parameter value, select the decimal point position by short pressing the STOP button. , select the timing range (corresponding time 0.1 seconds ~ 999 minutes); short press the SET button to set the next parameter of the current mode, the process is the same as above.\u003cbr data-mce-fragment=\"1\"\u003e3) After setting the parameters of the selected mode, press and hold the SET button for 2 seconds to release, the currently set mode will flash, then return to the main interface and set the parameters successfully.\u003cbr data-mce-fragment=\"1\"\u003e4) Main interface: “000” (no decimal point) is displayed when the MOS tube is not working, and the MOS tube has a decimal point in the working state.\u003cbr data-mce-fragment=\"1\"\u003e5) Mode selection interface: long press SET button to enter, after setting is completed, long press SET button to exit, return to the main interface\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cstrong data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eNote:\u003c\/span\u003e\u003c\/strong\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eThe module is an active live output, and the voltage at the output (load) is equal to the input voltage DC\u003c\/span\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e5.USD Digital Display Delay Controller: ( DC12V 4 Button )\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eDescription:\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003eThis relay delay control board has a powerful and clear interface, powerful function, one-button emergency stop function (STOP button), with reverse connection protection, reverse connection without burning, power-off memory. Increased sleep mode, after enabling, No operation within 5 minutes, automatically turn off the display, wake up any button! You can set different OP, CL, LOP parameters, these parameters are independent of each other, save the setting parameters automatically power-down save and other functions, almost meet all needs!\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eProduct manual:\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eWorking voltage: DC6V-DC30V (wide voltage anti-connection protection)\u003cbr data-mce-fragment=\"1\"\u003eTrigger signal source: high-level trigger DC 3.0V—24V signal ground and system ground to improve the system's anti-interference ability can also short-circuit the ground\u003cbr data-mce-fragment=\"1\"\u003eOutput capacity: controllable DC 30V\/10A or AC 250V\/10A equipment\u003cbr data-mce-fragment=\"1\"\u003eProduct size: 64mm*35mm*19.3mm\u003cbr data-mce-fragment=\"1\"\u003eMounting hole: diameter 3mm\u003cbr data-mce-fragment=\"1\"\u003eWorking temperature: -40 ° C ~ 85 ° C\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e6.DC Motor Speed Controller :(DC 8-55V Motor Speed Controller )\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eDescription:\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003eThis product brings together a wide range of modern motor speed control, with the advantages of small size, simple operation, high current resistance and reverse connection. Suitable for most users in various environments with various speeds, support acceleration and deceleration functions can be set through the menu, with set parameters power off permanent memory function\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eProduct manual:\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eVoltage: DC8V-55V (wide voltage anti-back protection)\u003cbr data-mce-fragment=\"1\"\u003eSpeed range: long press \/ short press to adjust the degree, 0% -100% speed\u003cbr data-mce-fragment=\"1\"\u003eDrive current: up to 10A, (recommended output series 12A fuse)\u003cbr data-mce-fragment=\"1\"\u003eStandby current: \u0026lt;17mA\u003cbr data-mce-fragment=\"1\"\u003eMounting hole: diameter 3mm\u003cbr data-mce-fragment=\"1\"\u003eProduct size: 64mm*35mm*19mm (length * width * height)\u003cbr data-mce-fragment=\"1\"\u003eWorking temperature: -20 ° C ~ 70 ° C\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eInstructions:\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e1. Click\/long press the “speed increase” button to increase the motor speed to 100%.\u003cbr data-mce-fragment=\"1\"\u003e2. Click\/long press the “speed down” button to increase the motor speed to a minimum of 0%.\u003cbr data-mce-fragment=\"1\"\u003e3. Press and hold the “Power On\/Off” button for one second, the controller will be turned on or off (the power is turned off by default, and the memory function is activated after booting)\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003ePrecautions:\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e1. The digital tube flashes at the moment of power-on (normal phenomenon, no need to worry)\u003cbr data-mce-fragment=\"1\"\u003e2, close to the limit drive current working conditions, it is recommended to take the output end of the fuse\u003cbr data-mce-fragment=\"1\"\u003e3. The DC motor speed controller cannot be installed in places where there is dripping water and children can reach it.\u003cbr data-mce-fragment=\"1\"\u003e4. After wiring, check if the line is correct and then energize, so as to avoid accidentally burning the temperature controller and load device.\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003eWiring:\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e“M+” and “M-” are respectively connected to the positive and negative terminals of the output, M+ is positive and M- is negative.\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e“VIN” and “GND” are respectively connected to the positive and negative terminals of the input terminal, Vin is positive and GND is negative (input power supply voltage is DC8V-55V)\u003c\/span\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e7.Temperature Controller:(DC 12V Temperrature Controller)\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eProduct Parameters:\u003c\/span\u003e\u003c\/strong\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003eControl range: -50~110°C\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eResolution: -9.9~99.9, 0.1°C, other temperature range, 1°C\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eTemperature measurement accuracy: 0.1 °C\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eControl accuracy: 0.1 ° C\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eHysteresis accuracy: 0.1 ° C\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eRefresh rate: 0.5S\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eHigh temperature alarm: 0-110 °C\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eMeasurement input: NTC (10K0.5%) waterproof sensor\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eOutput: One way 10A relay\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eEnvironmental requirements: Temperature -10~60°C Humidity 20%-85%\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eSize: 48*40mm\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003ePower consumption of the whole machine: quiescent current: ≤35MA, Pull-in current: ≤65MA\u003c\/span\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eSetting Parameter Method:\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eOnce the power supply and load are connected, the control can be powered. After power-on, the digital tube displays the current real-time temperature. Press the SET button briefly, the digital tube displays the temperature flashing, press the + - button to adjust the set temperature; after the adjustment is completed, press the SET button to save the set temperature and return. At this time, the controller automatically Execute the relay on and off; press and hold the SET button for 5 seconds to enter the menu parameter setting, short press the + - button to switch P0...P6, short press the SET button to enter the menu.\u003cbr data-mce-fragment=\"1\"\u003eThe thermostat output is a 10A relay to meet a variety of high power loads, please ensure that the line is correct.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eIndicator light, digital tube status description:\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eIndicator light: Off means the relay is off, steady light means the relay is closed\u003cbr data-mce-fragment=\"1\"\u003eDigital tube: Display LLL for sensor open circuit: Display HHH is out of measurement range. The thermostat will forcibly open the relay.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eParameter Function Description:\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003ctable data-mce-fragment=\"1\"\u003e\n\u003ctbody data-mce-fragment=\"1\"\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eMenu identifier\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eMenu function\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003ePredetermined area\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eFactory setting\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eP0\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eRefrigeration C \/ Heating H\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eC\/H\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eC\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eP1\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eBacklash\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e0.1-15\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e2.0\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eP2\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eMaximum set temperature\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e-50~110℃\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e110\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eP3\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eMinimum set temperature\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e-50~110℃\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e-50\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eP4\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eTemperature correction\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e-7.0~7.0℃\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e0.0\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eP5\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003ePress delay\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e0-10 minutes\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e0\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eP6\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eHigh temperature alarm\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eON\/OFF\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003eOFF\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003ePackage Included:\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e1PC*DC 12V 2\/3\/4 Button Time Delay Relay Motor Speed Temperrature Controller+Buzzer\u003cstrong data-mce-fragment=\"1\"\u003e(According to your choice)\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e","published_at":"2020-11-17T14:10:21+08:00","created_at":"2020-11-17T14:10:20+08:00","vendor":"DIYMORE","type":"","tags":[],"price":899,"price_min":899,"price_max":899,"available":true,"price_varies":false,"compare_at_price":null,"compare_at_price_min":0,"compare_at_price_max":0,"compare_at_price_varies":false,"variants":[{"id":37539263873224,"title":"DC 8-55V Motor Speed Controller","option1":"DC 8-55V Motor Speed Controller","option2":null,"option3":null,"sku":"100040","requires_shipping":true,"taxable":false,"featured_image":null,"available":true,"name":"5V\/12V 2\/3\/4 Button Timer Delay Relay Motor Speed Temperature Controller+Buzzer - DC 8-55V Motor Speed Controller","public_title":"DC 8-55V Motor Speed Controller","options":["DC 8-55V Motor Speed Controller"],"price":899,"weight":0,"compare_at_price":null,"inventory_management":"shopify","barcode":"","requires_selling_plan":false,"selling_plan_allocations":[]}],"images":["\/\/www.diymore.cc\/cdn\/shop\/products\/100040_1.jpg?v=1605593426","\/\/www.diymore.cc\/cdn\/shop\/products\/100040_2.jpg?v=1605593426","\/\/www.diymore.cc\/cdn\/shop\/products\/100040.jpg?v=1605593426","\/\/www.diymore.cc\/cdn\/shop\/products\/100040_8.jpg?v=1605593426","\/\/www.diymore.cc\/cdn\/shop\/products\/100040_867e837f-1764-4e74-953c-5a0322a10abe.jpg?v=1605593426","\/\/www.diymore.cc\/cdn\/shop\/products\/100040_7.jpg?v=1605593426","\/\/www.diymore.cc\/cdn\/shop\/products\/100040_4.jpg?v=1605593426","\/\/www.diymore.cc\/cdn\/shop\/products\/100040_5.jpg?v=1605593427","\/\/www.diymore.cc\/cdn\/shop\/products\/100040_6.jpg?v=1605593427","\/\/www.diymore.cc\/cdn\/shop\/products\/100040_3.jpg?v=1605593427"],"featured_image":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040_1.jpg?v=1605593426","options":["Size"],"media":[{"alt":null,"id":14960171581640,"position":1,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040_1.jpg?v=1605593426"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040_1.jpg?v=1605593426","width":1000},{"alt":null,"id":14960171614408,"position":2,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040_2.jpg?v=1605593426"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040_2.jpg?v=1605593426","width":1000},{"alt":null,"id":14960171647176,"position":3,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040.jpg?v=1605593426"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040.jpg?v=1605593426","width":1000},{"alt":null,"id":14960171679944,"position":4,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040_8.jpg?v=1605593426"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040_8.jpg?v=1605593426","width":1000},{"alt":null,"id":14960171712712,"position":5,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040_867e837f-1764-4e74-953c-5a0322a10abe.jpg?v=1605593426"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040_867e837f-1764-4e74-953c-5a0322a10abe.jpg?v=1605593426","width":1000},{"alt":null,"id":14960171745480,"position":6,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040_7.jpg?v=1605593426"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040_7.jpg?v=1605593426","width":1000},{"alt":null,"id":14960171778248,"position":7,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040_4.jpg?v=1605593426"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040_4.jpg?v=1605593426","width":1000},{"alt":null,"id":14960171811016,"position":8,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040_5.jpg?v=1605593427"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040_5.jpg?v=1605593427","width":1000},{"alt":null,"id":14960171843784,"position":9,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040_6.jpg?v=1605593427"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040_6.jpg?v=1605593427","width":1000},{"alt":null,"id":14960171876552,"position":10,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040_3.jpg?v=1605593427"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040_3.jpg?v=1605593427","width":1000}],"requires_selling_plan":false,"selling_plan_groups":[],"content":"\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e1.Digital Display Delay Controller:(DC 12V with Buzzer 2 Button\u003cspan face=\"helveticao\" data-mce-fragment=\"1\"\u003e)\u003c\/span\u003e\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eProduct parameters\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\n\u003cul data-mce-fragment=\"1\"\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eWorking voltage: DC12V (normal working voltage DC10V-16V)\u003c\/span\u003e\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eSignal source: DC4V~20V (usual power supply positive trigger, button, PNP sensor, PLC signal, etc.)\u003c\/span\u003e\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eOutput capability: It can control devices within 30v5A or within 220v5A\u003c\/span\u003e\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eQuiescent current: 20mA, working current: 50mA\u003c\/span\u003e\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eService life: more than 100,000 times;\u003c\/span\u003e\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eWorking temperature: -40~85 °C;\u003c\/span\u003e\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eNet weight: about 26g\u003c\/span\u003e\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eSize: 64.2mm*34.8mm*18.5mm\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eFeatures\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\n\u003cul data-mce-fragment=\"1\"\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eVoltage input anti-reverse circuit, worry-free wiring. Signal input optocoupler isolation, strong anti-interference ability. Set the parameter to power off permanent memory. Powerful flash MCU online programming function, according to user needs can contact the manufacturer to customize the required functions.\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eFunction introduction\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\n\u003cul data-mce-fragment=\"1\"\u003e\n\u003cli data-mce-fragment=\"1\"\u003eWhen the power is turned on, the trigger signal is received, the countdown starts, and the relay works. When the timer ends, the relay stops working, the time returns to the setting, and the next trigger signal is waited.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eInstructions\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cul data-mce-fragment=\"1\"\u003e\n\u003cli data-mce-fragment=\"1\"\u003e1).Press K1 to enter the time setting, the hundred digit digital tube starts to flash; press K2 at this time, the hundred digits change; press K1 again, the ten digital tube starts to flash; press K2 at this time, the ten digits change; press again After K1, the digital tube starts to flash. At this time, press K2, the digit of the digit changes; press K1 again to exit the setting, and the digital tube no longer flashes.\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003e2).When the digital tube is normally displayed, press K2, the decimal point is shifted, the decimal point is 0 to 999 seconds in ones digit, the decimal point is 0 to 99.9 seconds in ten digits, and the decimal point is 0 to 999 minutes; the time is set.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e2.Digital Display Delay Controller:(DC 12V 3 Button)\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eProduct parameters\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eWorking voltage: DC12V (normal working voltage DC10V-16V)\u003cbr data-mce-fragment=\"1\"\u003eSource: DC4V~20V (usual power supply positive trigger, button, PNP sensor, PLC signal, etc.)\u003cbr data-mce-fragment=\"1\"\u003eOutput capability: It can control devices within 30v5A or within 220v5A\u003cbr data-mce-fragment=\"1\"\u003eQuiescent current: 20mA, working current: 50mA\u003cbr data-mce-fragment=\"1\"\u003eService life: more than 100,000 times;\u003cbr data-mce-fragment=\"1\"\u003eWorking temperature: -40~85 °C;\u003cbr data-mce-fragment=\"1\"\u003eNet weight: about 26g\u003cbr data-mce-fragment=\"1\"\u003eSize: 64.2mm*34.8mm*18.5mm\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eFeatures\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eVoltage input anti-reverse circuit, worry-free wiring. Signal input optocoupler isolation, strong anti-interference ability. Set the parameter to power off permanent memory. Powerful flash MCU online programming function, according to user needs can contact the manufacturer to customize the required functions.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eWiring diagram\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cimg src=\"https:\/\/pg-cdn-a2.datacaciques.com\/00\/NDAy\/19\/08\/21\/02s76nl1201bce4t\/76050b0dfcc5297c.jpg\" data-mce-fragment=\"1\" data-mce-src=\"https:\/\/pg-cdn-a2.datacaciques.com\/00\/NDAy\/19\/08\/21\/02s76nl1201bce4t\/76050b0dfcc5297c.jpg\"\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eFunction introduction\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eP-1: The signal triggers the relay to pull in. When the time is up, the relay is disconnected during the delay.\u003cbr data-mce-fragment=\"1\"\u003eA: Invalid trigger again B: Re-trigger re-clocking C: Trigger relay reset again to stop timing\u003cbr data-mce-fragment=\"1\"\u003eP-2: The signal trigger start timing time T1, the time is up to the relay pull-in time T2 is disconnected (reset)\u003cbr data-mce-fragment=\"1\"\u003eA: Invalid trigger again B: Re-trigger re-clocking C: Start delay without triggering power-on\u003cbr data-mce-fragment=\"1\"\u003eP-3: Cycling: Turn on T1, disconnect T2, infinite loop. For T1 and T2, the time is adjustable; if a parameter is turned ON or OFF, it can be turned on or the power is turned on.\u003cbr data-mce-fragment=\"1\"\u003eA: The relay is turned on immediately after power-on. B: The relay is turned off and then turned on after power-on.\u003cbr data-mce-fragment=\"1\"\u003eP-4: There is signal, the relay is closed, the suction is kept, the signal disappears, the timing starts, the time is up, the relay is disconnected, during the delay, the signal is given again, the delay is cancelled, the relay is kept, the signal disappears, and the time is re-timed.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cstrong data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eNotes\u003c\/span\u003e\u003c\/strong\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eThe relay output is a passive contact that has no live output and controls the on\/off of a line.\u003c\/span\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e\u003cspan face=\"helveticao\" data-mce-fragment=\"1\"\u003e3.Digital Display Delay Controller:(DC 12V with Buzzer 3 Button)\u003c\/span\u003e\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan face=\"helveticao\" data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eProduct parameters\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eWorking voltage: DC12V (normal working voltage DC10V-16V)\u003cbr data-mce-fragment=\"1\"\u003eSource: DC4V~20V (usual power supply positive trigger, button, PNP sensor, PLC signal, etc.)\u003cbr data-mce-fragment=\"1\"\u003eOutput capability: It can control devices within 30v5A or within 220v5A\u003cbr data-mce-fragment=\"1\"\u003eQuiescent current: 20mA, working current: 50mA\u003cbr data-mce-fragment=\"1\"\u003eService life: more than 100,000 times;\u003cbr data-mce-fragment=\"1\"\u003eWorking temperature: -40~85 °C;\u003cbr data-mce-fragment=\"1\"\u003eNet weight: about 26g\u003cbr data-mce-fragment=\"1\"\u003eSize: 64.2mm*34.8mm*18.5mm\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eFeatures\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003ePower input flash-coupled, strong-interference ability. Power of flash MCU online programming function, according to user needs can contact the manufacturer to customize the Required functions.\u003c\/span\u003e\u003cspan face=\"helveticao\" data-mce-fragment=\"1\"\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003c\/span\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003eFunction introduction\u003cbr data-mce-fragment=\"1\"\u003eP-1: The trigger signal is received, the relay is turned on, the timer expires, and the relay is turned off.\u003cbr data-mce-fragment=\"1\"\u003eA1: Invalid again during delayed trigger\u003cbr data-mce-fragment=\"1\"\u003eA2: Trigger again during retiming delay\u003cbr data-mce-fragment=\"1\"\u003eA3: During the delay trigger, the trigger signal is received again to terminate the current delay.\u003cbr data-mce-fragment=\"1\"\u003eP-2: Receive trigger signal, X start time, relay off, Y start time, relay open\u003cbr data-mce-fragment=\"1\"\u003eP-3: Cycle switching mode\u003cbr data-mce-fragment=\"1\"\u003eA1: After the power relay is turned on, the timing is turned off and the loop is infinite.\u003cbr data-mce-fragment=\"1\"\u003eA2: After the power relay is turned off, the timing ends and the loop is infinite.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cstrong data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eNotes:\u003c\/span\u003e\u003c\/strong\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eThe relay output is a passive contact that has no live output and controls the on\/off of a line.\u003c\/span\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e4.Dual MOS delay control board: (DC 5-30V 4 Button)\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eDescription:\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003eDual MOS parallel active output, lower internal resistance, larger current, strong power interface, clear and simple, powerful, one-button emergency stop function (STOP button), with reverse connection protection, reverse connection, no burning, power-off memory. Increase Sleep mode, after enabling, no operation within 5 minutes, automatically turn off the display, wake up any button! You can set different OP, CL, LOP parameters, these parameters are independent of each other, save the setting parameters automatically power-down save and other functions, Almost all the needs!\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eProduct manual\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eWorking voltage: DC5V-DC30V (wide voltage anti-connection protection)\u003cbr data-mce-fragment=\"1\"\u003eTrigger signal source: high-level trigger DC 3.0V—24V signal ground and system ground to improve the system's anti-interference ability can also short-circuit the ground\u003cbr data-mce-fragment=\"1\"\u003eOutput capacity: DC DC 5V--36V, continuous current 15A at normal temperature, power 400W! Under the condition of auxiliary heat dissipation, the maximum current can reach 30A\u003cbr data-mce-fragment=\"1\"\u003eProduct size: 64mm*35mm*19.3mm\u003cbr data-mce-fragment=\"1\"\u003eMounting hole: diameter 3mm\u003cbr data-mce-fragment=\"1\"\u003eWorking temperature: -40 ° C ~ 85 ° C\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eOperating mode\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eP1 mode: After the signal is triggered, the MOS transistor turns on the OP time and then turns off; in the OP time, the following operation\u003cbr data-mce-fragment=\"1\"\u003eP1.1: The signal is triggered again.\u003cbr data-mce-fragment=\"1\"\u003eP1.2: Signal triggers re-timed again\u003cbr data-mce-fragment=\"1\"\u003eP1.3: The signal triggers reset again, the MOS tube is disconnected, and the timing is stopped.\u003cbr data-mce-fragment=\"1\"\u003eP-2: Give the trigger signal, after the MOS transistor is disconnected from the CL time, the MOS transistor turns on the OP time. After the timing is completed, the MOS transistor is disconnected.\u003cbr data-mce-fragment=\"1\"\u003eP3.1: Give the trigger signal, after the MOS transistor turns on the OP time, the MOS tube turns off the CL time, then loops the above action, the signal is given again in the loop, the MOS tube is disconnected, the timing is stopped; the number of cycles (LOP) can be set.\u003cbr data-mce-fragment=\"1\"\u003eP3.2: No need to trigger signal after power-on, MOS tube turns on OP time, MOS tube disconnects CL time, loops the above action; loop number (LOP) can be set\u003cbr data-mce-fragment=\"1\"\u003eP-4: Signal hold function If there is a trigger signal, the timing is cleared, the MOS transistor remains on; when the signal disappears, the MOS transistor is disconnected after timing the OP; during the timing, there is a signal and the timing is cleared.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eRelay enable mode\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eON : MOS tube is allowed to conduct during OP conduction time\u003cbr data-mce-fragment=\"1\"\u003eOFF : MOS tube is disabled, always off\u003cbr data-mce-fragment=\"1\"\u003eShort press the STOP button on the main interface to switch between ON and OFF. The current state will flash, then return to the main interface. This function is the emergency stop function. One button is used to open and close the MOS tube.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eSleep mode (long press the stop button to view the current mode)\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eC-P sleep mode: within five minutes, without any operation, the digital tube automatically turns off the display, the program runs normally.\u003cbr data-mce-fragment=\"1\"\u003eO-d normal mode: the digital tube is always on display\u003cbr data-mce-fragment=\"1\"\u003ePress and hold the STOP button for 2 seconds and then release to switch the C-P and O-d states. The current state will flash and then return to the main interface.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eTiming range\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eHow to choose the timing range\u003cbr data-mce-fragment=\"1\"\u003e1).After setting the parameter value in the mode selection interface, press the STOP button to select the timing range.\u003cbr data-mce-fragment=\"1\"\u003eXXX. Decimal point is in one place, timing range: 1 second to 999 seconds\u003cbr data-mce-fragment=\"1\"\u003eXX.X decimal point in ten, timing range: 0.1 seconds to 99.9 seconds\u003cbr data-mce-fragment=\"1\"\u003eX.X.X. The decimal point is fully illuminated, the timing range is from 1 minute to 999 minutes.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e2).For example, if you want to set the OP to 3.2 seconds, move the decimal point to ten digits, and the digital tube displays 03.2.\u003cbr data-mce-fragment=\"1\"\u003eParameter description: OP on time, CL off time, LOP cycle number 1-999 times, \"---\" stands for infinite loop.\u003cbr data-mce-fragment=\"1\"\u003eThese parameters are independent of each other, but each mode shares these parameters. For example, when the on-time OP is set to 5 seconds in P1.1, the user wants to switch to the P1.2 mode, then when entering the P1.2 setting corresponding parameters, the OP also It will be 5 seconds.\u003cbr data-mce-fragment=\"1\"\u003eDisplaying 000 on the main interface and pressing the SET button will display OPL, LOP and corresponding time XXX\u003cbr data-mce-fragment=\"1\"\u003eIf only OP in the mode, such as mode P1.1, P1.2, P1.3 time, then short press SET button will only display OP and corresponding time.\u003cbr data-mce-fragment=\"1\"\u003eIf the mode has OP, CL, LOP such as mode P3.1, P3.2 short press SET button will display OP and corresponding time, CL and corresponding time, LOP and corresponding times.\u003cbr data-mce-fragment=\"1\"\u003eAfter setting the mode, it is very convenient to easily check the parameters set in the current mode by pressing the SET button on the main interface.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eHow to set parameters\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e1) First determine the working mode of the MOS tube\u003cbr data-mce-fragment=\"1\"\u003eAccording to the working mode of the MOS tube, in the main interface (when the module is powered on, it will flash the current working mode (default P1.1 mode), then enter the main interface \"press and hold the SET button for 2 seconds and then release\" to enter the mode. Select the interface, press the UP, DOWN button to select the mode to be set P1.1~P-4\u003cbr data-mce-fragment=\"1\"\u003e2) After selecting the mode to be set (for example, P3.2), press the SET button to set the corresponding parameter. At this time, the parameter to be set will flash OP ON time, CL OFF time, LOP cycle number “---” Represents an infinite loop, adjusts the parameter value through UP and DOWN, supports long press (rapid increase or decrease) and short press (increase or decrease 1 unit); after setting the parameter value, select the decimal point position by short pressing the STOP button. , select the timing range (corresponding time 0.1 seconds ~ 999 minutes); short press the SET button to set the next parameter of the current mode, the process is the same as above.\u003cbr data-mce-fragment=\"1\"\u003e3) After setting the parameters of the selected mode, press and hold the SET button for 2 seconds to release, the currently set mode will flash, then return to the main interface and set the parameters successfully.\u003cbr data-mce-fragment=\"1\"\u003e4) Main interface: “000” (no decimal point) is displayed when the MOS tube is not working, and the MOS tube has a decimal point in the working state.\u003cbr data-mce-fragment=\"1\"\u003e5) Mode selection interface: long press SET button to enter, after setting is completed, long press SET button to exit, return to the main interface\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cstrong data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eNote:\u003c\/span\u003e\u003c\/strong\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eThe module is an active live output, and the voltage at the output (load) is equal to the input voltage DC\u003c\/span\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e5.USD Digital Display Delay Controller: ( DC12V 4 Button )\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eDescription:\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003eThis relay delay control board has a powerful and clear interface, powerful function, one-button emergency stop function (STOP button), with reverse connection protection, reverse connection without burning, power-off memory. Increased sleep mode, after enabling, No operation within 5 minutes, automatically turn off the display, wake up any button! You can set different OP, CL, LOP parameters, these parameters are independent of each other, save the setting parameters automatically power-down save and other functions, almost meet all needs!\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eProduct manual:\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eWorking voltage: DC6V-DC30V (wide voltage anti-connection protection)\u003cbr data-mce-fragment=\"1\"\u003eTrigger signal source: high-level trigger DC 3.0V—24V signal ground and system ground to improve the system's anti-interference ability can also short-circuit the ground\u003cbr data-mce-fragment=\"1\"\u003eOutput capacity: controllable DC 30V\/10A or AC 250V\/10A equipment\u003cbr data-mce-fragment=\"1\"\u003eProduct size: 64mm*35mm*19.3mm\u003cbr data-mce-fragment=\"1\"\u003eMounting hole: diameter 3mm\u003cbr data-mce-fragment=\"1\"\u003eWorking temperature: -40 ° C ~ 85 ° C\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e6.DC Motor Speed Controller :(DC 8-55V Motor Speed Controller )\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eDescription:\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003eThis product brings together a wide range of modern motor speed control, with the advantages of small size, simple operation, high current resistance and reverse connection. Suitable for most users in various environments with various speeds, support acceleration and deceleration functions can be set through the menu, with set parameters power off permanent memory function\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eProduct manual:\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eVoltage: DC8V-55V (wide voltage anti-back protection)\u003cbr data-mce-fragment=\"1\"\u003eSpeed range: long press \/ short press to adjust the degree, 0% -100% speed\u003cbr data-mce-fragment=\"1\"\u003eDrive current: up to 10A, (recommended output series 12A fuse)\u003cbr data-mce-fragment=\"1\"\u003eStandby current: \u0026lt;17mA\u003cbr data-mce-fragment=\"1\"\u003eMounting hole: diameter 3mm\u003cbr data-mce-fragment=\"1\"\u003eProduct size: 64mm*35mm*19mm (length * width * height)\u003cbr data-mce-fragment=\"1\"\u003eWorking temperature: -20 ° C ~ 70 ° C\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eInstructions:\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e1. Click\/long press the “speed increase” button to increase the motor speed to 100%.\u003cbr data-mce-fragment=\"1\"\u003e2. Click\/long press the “speed down” button to increase the motor speed to a minimum of 0%.\u003cbr data-mce-fragment=\"1\"\u003e3. Press and hold the “Power On\/Off” button for one second, the controller will be turned on or off (the power is turned off by default, and the memory function is activated after booting)\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003ePrecautions:\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e1. The digital tube flashes at the moment of power-on (normal phenomenon, no need to worry)\u003cbr data-mce-fragment=\"1\"\u003e2, close to the limit drive current working conditions, it is recommended to take the output end of the fuse\u003cbr data-mce-fragment=\"1\"\u003e3. The DC motor speed controller cannot be installed in places where there is dripping water and children can reach it.\u003cbr data-mce-fragment=\"1\"\u003e4. After wiring, check if the line is correct and then energize, so as to avoid accidentally burning the temperature controller and load device.\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003eWiring:\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e“M+” and “M-” are respectively connected to the positive and negative terminals of the output, M+ is positive and M- is negative.\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e“VIN” and “GND” are respectively connected to the positive and negative terminals of the input terminal, Vin is positive and GND is negative (input power supply voltage is DC8V-55V)\u003c\/span\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e7.Temperature Controller:(DC 12V Temperrature Controller)\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eProduct Parameters:\u003c\/span\u003e\u003c\/strong\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003eControl range: -50~110°C\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eResolution: -9.9~99.9, 0.1°C, other temperature range, 1°C\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eTemperature measurement accuracy: 0.1 °C\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eControl accuracy: 0.1 ° C\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eHysteresis accuracy: 0.1 ° C\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eRefresh rate: 0.5S\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eHigh temperature alarm: 0-110 °C\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eMeasurement input: NTC (10K0.5%) waterproof sensor\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eOutput: One way 10A relay\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eEnvironmental requirements: Temperature -10~60°C Humidity 20%-85%\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eSize: 48*40mm\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003ePower consumption of the whole machine: quiescent current: ≤35MA, Pull-in current: ≤65MA\u003c\/span\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eSetting Parameter Method:\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eOnce the power supply and load are connected, the control can be powered. After power-on, the digital tube displays the current real-time temperature. Press the SET button briefly, the digital tube displays the temperature flashing, press the + - button to adjust the set temperature; after the adjustment is completed, press the SET button to save the set temperature and return. At this time, the controller automatically Execute the relay on and off; press and hold the SET button for 5 seconds to enter the menu parameter setting, short press the + - button to switch P0...P6, short press the SET button to enter the menu.\u003cbr data-mce-fragment=\"1\"\u003eThe thermostat output is a 10A relay to meet a variety of high power loads, please ensure that the line is correct.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eIndicator light, digital tube status description:\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eIndicator light: Off means the relay is off, steady light means the relay is closed\u003cbr data-mce-fragment=\"1\"\u003eDigital tube: Display LLL for sensor open circuit: Display HHH is out of measurement range. The thermostat will forcibly open the relay.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eParameter Function Description:\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003ctable data-mce-fragment=\"1\"\u003e\n\u003ctbody data-mce-fragment=\"1\"\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eMenu identifier\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eMenu function\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003ePredetermined area\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eFactory setting\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eP0\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eRefrigeration C \/ Heating H\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eC\/H\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eC\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eP1\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eBacklash\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e0.1-15\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e2.0\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eP2\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eMaximum set temperature\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e-50~110℃\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e110\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eP3\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eMinimum set temperature\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e-50~110℃\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e-50\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eP4\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eTemperature correction\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e-7.0~7.0℃\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e0.0\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eP5\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003ePress delay\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e0-10 minutes\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e0\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eP6\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eHigh temperature alarm\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eON\/OFF\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003eOFF\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003ePackage Included:\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e1PC*DC 12V 2\/3\/4 Button Time Delay Relay Motor Speed Temperrature Controller+Buzzer\u003cstrong data-mce-fragment=\"1\"\u003e(According to your choice)\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e"}
-
Translation missing: en.products.product.regular_price $5.99{"id":6086411911368,"title":"5V\/12V 2\/3\/4 Button Timer Delay Relay Motor Speed Temperature Controller+Buzzer","handle":"5v-12v-2-3-4-button-timer-delay-relay-motor-speed-temperature-controller-buzzer","description":"\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e1.Digital Display Delay Controller:(DC 12V with Buzzer 2 Button\u003cspan face=\"helveticao\" data-mce-fragment=\"1\"\u003e)\u003c\/span\u003e\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eProduct parameters\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\n\u003cul data-mce-fragment=\"1\"\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eWorking voltage: DC12V (normal working voltage DC10V-16V)\u003c\/span\u003e\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eSignal source: DC4V~20V (usual power supply positive trigger, button, PNP sensor, PLC signal, etc.)\u003c\/span\u003e\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eOutput capability: It can control devices within 30v5A or within 220v5A\u003c\/span\u003e\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eQuiescent current: 20mA, working current: 50mA\u003c\/span\u003e\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eService life: more than 100,000 times;\u003c\/span\u003e\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eWorking temperature: -40~85 °C;\u003c\/span\u003e\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eNet weight: about 26g\u003c\/span\u003e\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eSize: 64.2mm*34.8mm*18.5mm\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eFeatures\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\n\u003cul data-mce-fragment=\"1\"\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eVoltage input anti-reverse circuit, worry-free wiring. Signal input optocoupler isolation, strong anti-interference ability. Set the parameter to power off permanent memory. Powerful flash MCU online programming function, according to user needs can contact the manufacturer to customize the required functions.\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eFunction introduction\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\n\u003cul data-mce-fragment=\"1\"\u003e\n\u003cli data-mce-fragment=\"1\"\u003eWhen the power is turned on, the trigger signal is received, the countdown starts, and the relay works. When the timer ends, the relay stops working, the time returns to the setting, and the next trigger signal is waited.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eInstructions\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cul data-mce-fragment=\"1\"\u003e\n\u003cli data-mce-fragment=\"1\"\u003e1).Press K1 to enter the time setting, the hundred digit digital tube starts to flash; press K2 at this time, the hundred digits change; press K1 again, the ten digital tube starts to flash; press K2 at this time, the ten digits change; press again After K1, the digital tube starts to flash. At this time, press K2, the digit of the digit changes; press K1 again to exit the setting, and the digital tube no longer flashes.\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003e2).When the digital tube is normally displayed, press K2, the decimal point is shifted, the decimal point is 0 to 999 seconds in ones digit, the decimal point is 0 to 99.9 seconds in ten digits, and the decimal point is 0 to 999 minutes; the time is set.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e2.Digital Display Delay Controller:(DC 12V 3 Button)\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eProduct parameters\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eWorking voltage: DC12V (normal working voltage DC10V-16V)\u003cbr data-mce-fragment=\"1\"\u003eSource: DC4V~20V (usual power supply positive trigger, button, PNP sensor, PLC signal, etc.)\u003cbr data-mce-fragment=\"1\"\u003eOutput capability: It can control devices within 30v5A or within 220v5A\u003cbr data-mce-fragment=\"1\"\u003eQuiescent current: 20mA, working current: 50mA\u003cbr data-mce-fragment=\"1\"\u003eService life: more than 100,000 times;\u003cbr data-mce-fragment=\"1\"\u003eWorking temperature: -40~85 °C;\u003cbr data-mce-fragment=\"1\"\u003eNet weight: about 26g\u003cbr data-mce-fragment=\"1\"\u003eSize: 64.2mm*34.8mm*18.5mm\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eFeatures\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eVoltage input anti-reverse circuit, worry-free wiring. Signal input optocoupler isolation, strong anti-interference ability. Set the parameter to power off permanent memory. Powerful flash MCU online programming function, according to user needs can contact the manufacturer to customize the required functions.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eWiring diagram\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cimg src=\"https:\/\/pg-cdn-a2.datacaciques.com\/00\/NDAy\/19\/08\/21\/02s76nl1201bce4t\/76050b0dfcc5297c.jpg\" data-mce-fragment=\"1\" data-mce-src=\"https:\/\/pg-cdn-a2.datacaciques.com\/00\/NDAy\/19\/08\/21\/02s76nl1201bce4t\/76050b0dfcc5297c.jpg\"\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eFunction introduction\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eP-1: The signal triggers the relay to pull in. When the time is up, the relay is disconnected during the delay.\u003cbr data-mce-fragment=\"1\"\u003eA: Invalid trigger again B: Re-trigger re-clocking C: Trigger relay reset again to stop timing\u003cbr data-mce-fragment=\"1\"\u003eP-2: The signal trigger start timing time T1, the time is up to the relay pull-in time T2 is disconnected (reset)\u003cbr data-mce-fragment=\"1\"\u003eA: Invalid trigger again B: Re-trigger re-clocking C: Start delay without triggering power-on\u003cbr data-mce-fragment=\"1\"\u003eP-3: Cycling: Turn on T1, disconnect T2, infinite loop. For T1 and T2, the time is adjustable; if a parameter is turned ON or OFF, it can be turned on or the power is turned on.\u003cbr data-mce-fragment=\"1\"\u003eA: The relay is turned on immediately after power-on. B: The relay is turned off and then turned on after power-on.\u003cbr data-mce-fragment=\"1\"\u003eP-4: There is signal, the relay is closed, the suction is kept, the signal disappears, the timing starts, the time is up, the relay is disconnected, during the delay, the signal is given again, the delay is cancelled, the relay is kept, the signal disappears, and the time is re-timed.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cstrong data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eNotes\u003c\/span\u003e\u003c\/strong\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eThe relay output is a passive contact that has no live output and controls the on\/off of a line.\u003c\/span\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e\u003cspan face=\"helveticao\" data-mce-fragment=\"1\"\u003e3.Digital Display Delay Controller:(DC 12V with Buzzer 3 Button)\u003c\/span\u003e\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan face=\"helveticao\" data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eProduct parameters\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eWorking voltage: DC12V (normal working voltage DC10V-16V)\u003cbr data-mce-fragment=\"1\"\u003eSource: DC4V~20V (usual power supply positive trigger, button, PNP sensor, PLC signal, etc.)\u003cbr data-mce-fragment=\"1\"\u003eOutput capability: It can control devices within 30v5A or within 220v5A\u003cbr data-mce-fragment=\"1\"\u003eQuiescent current: 20mA, working current: 50mA\u003cbr data-mce-fragment=\"1\"\u003eService life: more than 100,000 times;\u003cbr data-mce-fragment=\"1\"\u003eWorking temperature: -40~85 °C;\u003cbr data-mce-fragment=\"1\"\u003eNet weight: about 26g\u003cbr data-mce-fragment=\"1\"\u003eSize: 64.2mm*34.8mm*18.5mm\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eFeatures\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003ePower input flash-coupled, strong-interference ability. Power of flash MCU online programming function, according to user needs can contact the manufacturer to customize the Required functions.\u003c\/span\u003e\u003cspan face=\"helveticao\" data-mce-fragment=\"1\"\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003c\/span\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003eFunction introduction\u003cbr data-mce-fragment=\"1\"\u003eP-1: The trigger signal is received, the relay is turned on, the timer expires, and the relay is turned off.\u003cbr data-mce-fragment=\"1\"\u003eA1: Invalid again during delayed trigger\u003cbr data-mce-fragment=\"1\"\u003eA2: Trigger again during retiming delay\u003cbr data-mce-fragment=\"1\"\u003eA3: During the delay trigger, the trigger signal is received again to terminate the current delay.\u003cbr data-mce-fragment=\"1\"\u003eP-2: Receive trigger signal, X start time, relay off, Y start time, relay open\u003cbr data-mce-fragment=\"1\"\u003eP-3: Cycle switching mode\u003cbr data-mce-fragment=\"1\"\u003eA1: After the power relay is turned on, the timing is turned off and the loop is infinite.\u003cbr data-mce-fragment=\"1\"\u003eA2: After the power relay is turned off, the timing ends and the loop is infinite.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cstrong data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eNotes:\u003c\/span\u003e\u003c\/strong\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eThe relay output is a passive contact that has no live output and controls the on\/off of a line.\u003c\/span\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e4.Dual MOS delay control board: (DC 5-30V 4 Button)\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eDescription:\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003eDual MOS parallel active output, lower internal resistance, larger current, strong power interface, clear and simple, powerful, one-button emergency stop function (STOP button), with reverse connection protection, reverse connection, no burning, power-off memory. Increase Sleep mode, after enabling, no operation within 5 minutes, automatically turn off the display, wake up any button! You can set different OP, CL, LOP parameters, these parameters are independent of each other, save the setting parameters automatically power-down save and other functions, Almost all the needs!\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eProduct manual\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eWorking voltage: DC5V-DC30V (wide voltage anti-connection protection)\u003cbr data-mce-fragment=\"1\"\u003eTrigger signal source: high-level trigger DC 3.0V—24V signal ground and system ground to improve the system's anti-interference ability can also short-circuit the ground\u003cbr data-mce-fragment=\"1\"\u003eOutput capacity: DC DC 5V--36V, continuous current 15A at normal temperature, power 400W! Under the condition of auxiliary heat dissipation, the maximum current can reach 30A\u003cbr data-mce-fragment=\"1\"\u003eProduct size: 64mm*35mm*19.3mm\u003cbr data-mce-fragment=\"1\"\u003eMounting hole: diameter 3mm\u003cbr data-mce-fragment=\"1\"\u003eWorking temperature: -40 ° C ~ 85 ° C\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eOperating mode\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eP1 mode: After the signal is triggered, the MOS transistor turns on the OP time and then turns off; in the OP time, the following operation\u003cbr data-mce-fragment=\"1\"\u003eP1.1: The signal is triggered again.\u003cbr data-mce-fragment=\"1\"\u003eP1.2: Signal triggers re-timed again\u003cbr data-mce-fragment=\"1\"\u003eP1.3: The signal triggers reset again, the MOS tube is disconnected, and the timing is stopped.\u003cbr data-mce-fragment=\"1\"\u003eP-2: Give the trigger signal, after the MOS transistor is disconnected from the CL time, the MOS transistor turns on the OP time. After the timing is completed, the MOS transistor is disconnected.\u003cbr data-mce-fragment=\"1\"\u003eP3.1: Give the trigger signal, after the MOS transistor turns on the OP time, the MOS tube turns off the CL time, then loops the above action, the signal is given again in the loop, the MOS tube is disconnected, the timing is stopped; the number of cycles (LOP) can be set.\u003cbr data-mce-fragment=\"1\"\u003eP3.2: No need to trigger signal after power-on, MOS tube turns on OP time, MOS tube disconnects CL time, loops the above action; loop number (LOP) can be set\u003cbr data-mce-fragment=\"1\"\u003eP-4: Signal hold function If there is a trigger signal, the timing is cleared, the MOS transistor remains on; when the signal disappears, the MOS transistor is disconnected after timing the OP; during the timing, there is a signal and the timing is cleared.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eRelay enable mode\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eON : MOS tube is allowed to conduct during OP conduction time\u003cbr data-mce-fragment=\"1\"\u003eOFF : MOS tube is disabled, always off\u003cbr data-mce-fragment=\"1\"\u003eShort press the STOP button on the main interface to switch between ON and OFF. The current state will flash, then return to the main interface. This function is the emergency stop function. One button is used to open and close the MOS tube.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eSleep mode (long press the stop button to view the current mode)\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eC-P sleep mode: within five minutes, without any operation, the digital tube automatically turns off the display, the program runs normally.\u003cbr data-mce-fragment=\"1\"\u003eO-d normal mode: the digital tube is always on display\u003cbr data-mce-fragment=\"1\"\u003ePress and hold the STOP button for 2 seconds and then release to switch the C-P and O-d states. The current state will flash and then return to the main interface.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eTiming range\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eHow to choose the timing range\u003cbr data-mce-fragment=\"1\"\u003e1).After setting the parameter value in the mode selection interface, press the STOP button to select the timing range.\u003cbr data-mce-fragment=\"1\"\u003eXXX. Decimal point is in one place, timing range: 1 second to 999 seconds\u003cbr data-mce-fragment=\"1\"\u003eXX.X decimal point in ten, timing range: 0.1 seconds to 99.9 seconds\u003cbr data-mce-fragment=\"1\"\u003eX.X.X. The decimal point is fully illuminated, the timing range is from 1 minute to 999 minutes.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e2).For example, if you want to set the OP to 3.2 seconds, move the decimal point to ten digits, and the digital tube displays 03.2.\u003cbr data-mce-fragment=\"1\"\u003eParameter description: OP on time, CL off time, LOP cycle number 1-999 times, \"---\" stands for infinite loop.\u003cbr data-mce-fragment=\"1\"\u003eThese parameters are independent of each other, but each mode shares these parameters. For example, when the on-time OP is set to 5 seconds in P1.1, the user wants to switch to the P1.2 mode, then when entering the P1.2 setting corresponding parameters, the OP also It will be 5 seconds.\u003cbr data-mce-fragment=\"1\"\u003eDisplaying 000 on the main interface and pressing the SET button will display OPL, LOP and corresponding time XXX\u003cbr data-mce-fragment=\"1\"\u003eIf only OP in the mode, such as mode P1.1, P1.2, P1.3 time, then short press SET button will only display OP and corresponding time.\u003cbr data-mce-fragment=\"1\"\u003eIf the mode has OP, CL, LOP such as mode P3.1, P3.2 short press SET button will display OP and corresponding time, CL and corresponding time, LOP and corresponding times.\u003cbr data-mce-fragment=\"1\"\u003eAfter setting the mode, it is very convenient to easily check the parameters set in the current mode by pressing the SET button on the main interface.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eHow to set parameters\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e1) First determine the working mode of the MOS tube\u003cbr data-mce-fragment=\"1\"\u003eAccording to the working mode of the MOS tube, in the main interface (when the module is powered on, it will flash the current working mode (default P1.1 mode), then enter the main interface \"press and hold the SET button for 2 seconds and then release\" to enter the mode. Select the interface, press the UP, DOWN button to select the mode to be set P1.1~P-4\u003cbr data-mce-fragment=\"1\"\u003e2) After selecting the mode to be set (for example, P3.2), press the SET button to set the corresponding parameter. At this time, the parameter to be set will flash OP ON time, CL OFF time, LOP cycle number “---” Represents an infinite loop, adjusts the parameter value through UP and DOWN, supports long press (rapid increase or decrease) and short press (increase or decrease 1 unit); after setting the parameter value, select the decimal point position by short pressing the STOP button. , select the timing range (corresponding time 0.1 seconds ~ 999 minutes); short press the SET button to set the next parameter of the current mode, the process is the same as above.\u003cbr data-mce-fragment=\"1\"\u003e3) After setting the parameters of the selected mode, press and hold the SET button for 2 seconds to release, the currently set mode will flash, then return to the main interface and set the parameters successfully.\u003cbr data-mce-fragment=\"1\"\u003e4) Main interface: “000” (no decimal point) is displayed when the MOS tube is not working, and the MOS tube has a decimal point in the working state.\u003cbr data-mce-fragment=\"1\"\u003e5) Mode selection interface: long press SET button to enter, after setting is completed, long press SET button to exit, return to the main interface\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cstrong data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eNote:\u003c\/span\u003e\u003c\/strong\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eThe module is an active live output, and the voltage at the output (load) is equal to the input voltage DC\u003c\/span\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e5.USD Digital Display Delay Controller: ( DC12V 4 Button )\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eDescription:\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003eThis relay delay control board has a powerful and clear interface, powerful function, one-button emergency stop function (STOP button), with reverse connection protection, reverse connection without burning, power-off memory. Increased sleep mode, after enabling, No operation within 5 minutes, automatically turn off the display, wake up any button! You can set different OP, CL, LOP parameters, these parameters are independent of each other, save the setting parameters automatically power-down save and other functions, almost meet all needs!\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eProduct manual:\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eWorking voltage: DC6V-DC30V (wide voltage anti-connection protection)\u003cbr data-mce-fragment=\"1\"\u003eTrigger signal source: high-level trigger DC 3.0V—24V signal ground and system ground to improve the system's anti-interference ability can also short-circuit the ground\u003cbr data-mce-fragment=\"1\"\u003eOutput capacity: controllable DC 30V\/10A or AC 250V\/10A equipment\u003cbr data-mce-fragment=\"1\"\u003eProduct size: 64mm*35mm*19.3mm\u003cbr data-mce-fragment=\"1\"\u003eMounting hole: diameter 3mm\u003cbr data-mce-fragment=\"1\"\u003eWorking temperature: -40 ° C ~ 85 ° C\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e6.DC Motor Speed Controller :(DC 8-55V Motor Speed Controller )\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eDescription:\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003eThis product brings together a wide range of modern motor speed control, with the advantages of small size, simple operation, high current resistance and reverse connection. Suitable for most users in various environments with various speeds, support acceleration and deceleration functions can be set through the menu, with set parameters power off permanent memory function\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eProduct manual:\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eVoltage: DC8V-55V (wide voltage anti-back protection)\u003cbr data-mce-fragment=\"1\"\u003eSpeed range: long press \/ short press to adjust the degree, 0% -100% speed\u003cbr data-mce-fragment=\"1\"\u003eDrive current: up to 10A, (recommended output series 12A fuse)\u003cbr data-mce-fragment=\"1\"\u003eStandby current: \u0026lt;17mA\u003cbr data-mce-fragment=\"1\"\u003eMounting hole: diameter 3mm\u003cbr data-mce-fragment=\"1\"\u003eProduct size: 64mm*35mm*19mm (length * width * height)\u003cbr data-mce-fragment=\"1\"\u003eWorking temperature: -20 ° C ~ 70 ° C\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eInstructions:\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e1. Click\/long press the “speed increase” button to increase the motor speed to 100%.\u003cbr data-mce-fragment=\"1\"\u003e2. Click\/long press the “speed down” button to increase the motor speed to a minimum of 0%.\u003cbr data-mce-fragment=\"1\"\u003e3. Press and hold the “Power On\/Off” button for one second, the controller will be turned on or off (the power is turned off by default, and the memory function is activated after booting)\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003ePrecautions:\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e1. The digital tube flashes at the moment of power-on (normal phenomenon, no need to worry)\u003cbr data-mce-fragment=\"1\"\u003e2, close to the limit drive current working conditions, it is recommended to take the output end of the fuse\u003cbr data-mce-fragment=\"1\"\u003e3. The DC motor speed controller cannot be installed in places where there is dripping water and children can reach it.\u003cbr data-mce-fragment=\"1\"\u003e4. After wiring, check if the line is correct and then energize, so as to avoid accidentally burning the temperature controller and load device.\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003eWiring:\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e“M+” and “M-” are respectively connected to the positive and negative terminals of the output, M+ is positive and M- is negative.\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e“VIN” and “GND” are respectively connected to the positive and negative terminals of the input terminal, Vin is positive and GND is negative (input power supply voltage is DC8V-55V)\u003c\/span\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e7.Temperature Controller:(DC 12V Temperrature Controller)\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eProduct Parameters:\u003c\/span\u003e\u003c\/strong\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003eControl range: -50~110°C\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eResolution: -9.9~99.9, 0.1°C, other temperature range, 1°C\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eTemperature measurement accuracy: 0.1 °C\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eControl accuracy: 0.1 ° C\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eHysteresis accuracy: 0.1 ° C\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eRefresh rate: 0.5S\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eHigh temperature alarm: 0-110 °C\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eMeasurement input: NTC (10K0.5%) waterproof sensor\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eOutput: One way 10A relay\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eEnvironmental requirements: Temperature -10~60°C Humidity 20%-85%\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eSize: 48*40mm\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003ePower consumption of the whole machine: quiescent current: ≤35MA, Pull-in current: ≤65MA\u003c\/span\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eSetting Parameter Method:\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eOnce the power supply and load are connected, the control can be powered. After power-on, the digital tube displays the current real-time temperature. Press the SET button briefly, the digital tube displays the temperature flashing, press the + - button to adjust the set temperature; after the adjustment is completed, press the SET button to save the set temperature and return. At this time, the controller automatically Execute the relay on and off; press and hold the SET button for 5 seconds to enter the menu parameter setting, short press the + - button to switch P0...P6, short press the SET button to enter the menu.\u003cbr data-mce-fragment=\"1\"\u003eThe thermostat output is a 10A relay to meet a variety of high power loads, please ensure that the line is correct.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eIndicator light, digital tube status description:\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eIndicator light: Off means the relay is off, steady light means the relay is closed\u003cbr data-mce-fragment=\"1\"\u003eDigital tube: Display LLL for sensor open circuit: Display HHH is out of measurement range. The thermostat will forcibly open the relay.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eParameter Function Description:\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003ctable data-mce-fragment=\"1\"\u003e\n\u003ctbody data-mce-fragment=\"1\"\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eMenu identifier\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eMenu function\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003ePredetermined area\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eFactory setting\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eP0\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eRefrigeration C \/ Heating H\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eC\/H\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eC\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eP1\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eBacklash\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e0.1-15\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e2.0\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eP2\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eMaximum set temperature\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e-50~110℃\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e110\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eP3\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eMinimum set temperature\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e-50~110℃\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e-50\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eP4\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eTemperature correction\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e-7.0~7.0℃\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e0.0\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eP5\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003ePress delay\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e0-10 minutes\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e0\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eP6\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eHigh temperature alarm\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eON\/OFF\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003eOFF\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003ePackage Included:\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e1PC*DC 12V 2\/3\/4 Button Time Delay Relay Motor Speed Temperrature Controller+Buzzer\u003cstrong data-mce-fragment=\"1\"\u003e(According to your choice)\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e","published_at":"2020-11-17T14:10:21+08:00","created_at":"2020-11-17T14:10:20+08:00","vendor":"DIYMORE","type":"","tags":[],"price":899,"price_min":899,"price_max":899,"available":true,"price_varies":false,"compare_at_price":null,"compare_at_price_min":0,"compare_at_price_max":0,"compare_at_price_varies":false,"variants":[{"id":37539263873224,"title":"DC 8-55V Motor Speed Controller","option1":"DC 8-55V Motor Speed Controller","option2":null,"option3":null,"sku":"100040","requires_shipping":true,"taxable":false,"featured_image":null,"available":true,"name":"5V\/12V 2\/3\/4 Button Timer Delay Relay Motor Speed Temperature Controller+Buzzer - DC 8-55V Motor Speed Controller","public_title":"DC 8-55V Motor Speed Controller","options":["DC 8-55V Motor Speed Controller"],"price":899,"weight":0,"compare_at_price":null,"inventory_management":"shopify","barcode":"","requires_selling_plan":false,"selling_plan_allocations":[]}],"images":["\/\/www.diymore.cc\/cdn\/shop\/products\/100040_1.jpg?v=1605593426","\/\/www.diymore.cc\/cdn\/shop\/products\/100040_2.jpg?v=1605593426","\/\/www.diymore.cc\/cdn\/shop\/products\/100040.jpg?v=1605593426","\/\/www.diymore.cc\/cdn\/shop\/products\/100040_8.jpg?v=1605593426","\/\/www.diymore.cc\/cdn\/shop\/products\/100040_867e837f-1764-4e74-953c-5a0322a10abe.jpg?v=1605593426","\/\/www.diymore.cc\/cdn\/shop\/products\/100040_7.jpg?v=1605593426","\/\/www.diymore.cc\/cdn\/shop\/products\/100040_4.jpg?v=1605593426","\/\/www.diymore.cc\/cdn\/shop\/products\/100040_5.jpg?v=1605593427","\/\/www.diymore.cc\/cdn\/shop\/products\/100040_6.jpg?v=1605593427","\/\/www.diymore.cc\/cdn\/shop\/products\/100040_3.jpg?v=1605593427"],"featured_image":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040_1.jpg?v=1605593426","options":["Size"],"media":[{"alt":null,"id":14960171581640,"position":1,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040_1.jpg?v=1605593426"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040_1.jpg?v=1605593426","width":1000},{"alt":null,"id":14960171614408,"position":2,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040_2.jpg?v=1605593426"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040_2.jpg?v=1605593426","width":1000},{"alt":null,"id":14960171647176,"position":3,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040.jpg?v=1605593426"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040.jpg?v=1605593426","width":1000},{"alt":null,"id":14960171679944,"position":4,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040_8.jpg?v=1605593426"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040_8.jpg?v=1605593426","width":1000},{"alt":null,"id":14960171712712,"position":5,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040_867e837f-1764-4e74-953c-5a0322a10abe.jpg?v=1605593426"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040_867e837f-1764-4e74-953c-5a0322a10abe.jpg?v=1605593426","width":1000},{"alt":null,"id":14960171745480,"position":6,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040_7.jpg?v=1605593426"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040_7.jpg?v=1605593426","width":1000},{"alt":null,"id":14960171778248,"position":7,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040_4.jpg?v=1605593426"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040_4.jpg?v=1605593426","width":1000},{"alt":null,"id":14960171811016,"position":8,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040_5.jpg?v=1605593427"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040_5.jpg?v=1605593427","width":1000},{"alt":null,"id":14960171843784,"position":9,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040_6.jpg?v=1605593427"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040_6.jpg?v=1605593427","width":1000},{"alt":null,"id":14960171876552,"position":10,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040_3.jpg?v=1605593427"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040_3.jpg?v=1605593427","width":1000}],"requires_selling_plan":false,"selling_plan_groups":[],"content":"\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e1.Digital Display Delay Controller:(DC 12V with Buzzer 2 Button\u003cspan face=\"helveticao\" data-mce-fragment=\"1\"\u003e)\u003c\/span\u003e\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eProduct parameters\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\n\u003cul data-mce-fragment=\"1\"\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eWorking voltage: DC12V (normal working voltage DC10V-16V)\u003c\/span\u003e\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eSignal source: DC4V~20V (usual power supply positive trigger, button, PNP sensor, PLC signal, etc.)\u003c\/span\u003e\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eOutput capability: It can control devices within 30v5A or within 220v5A\u003c\/span\u003e\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eQuiescent current: 20mA, working current: 50mA\u003c\/span\u003e\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eService life: more than 100,000 times;\u003c\/span\u003e\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eWorking temperature: -40~85 °C;\u003c\/span\u003e\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eNet weight: about 26g\u003c\/span\u003e\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eSize: 64.2mm*34.8mm*18.5mm\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eFeatures\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\n\u003cul data-mce-fragment=\"1\"\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eVoltage input anti-reverse circuit, worry-free wiring. Signal input optocoupler isolation, strong anti-interference ability. Set the parameter to power off permanent memory. Powerful flash MCU online programming function, according to user needs can contact the manufacturer to customize the required functions.\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eFunction introduction\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\n\u003cul data-mce-fragment=\"1\"\u003e\n\u003cli data-mce-fragment=\"1\"\u003eWhen the power is turned on, the trigger signal is received, the countdown starts, and the relay works. When the timer ends, the relay stops working, the time returns to the setting, and the next trigger signal is waited.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eInstructions\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cul data-mce-fragment=\"1\"\u003e\n\u003cli data-mce-fragment=\"1\"\u003e1).Press K1 to enter the time setting, the hundred digit digital tube starts to flash; press K2 at this time, the hundred digits change; press K1 again, the ten digital tube starts to flash; press K2 at this time, the ten digits change; press again After K1, the digital tube starts to flash. At this time, press K2, the digit of the digit changes; press K1 again to exit the setting, and the digital tube no longer flashes.\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003e2).When the digital tube is normally displayed, press K2, the decimal point is shifted, the decimal point is 0 to 999 seconds in ones digit, the decimal point is 0 to 99.9 seconds in ten digits, and the decimal point is 0 to 999 minutes; the time is set.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e2.Digital Display Delay Controller:(DC 12V 3 Button)\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eProduct parameters\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eWorking voltage: DC12V (normal working voltage DC10V-16V)\u003cbr data-mce-fragment=\"1\"\u003eSource: DC4V~20V (usual power supply positive trigger, button, PNP sensor, PLC signal, etc.)\u003cbr data-mce-fragment=\"1\"\u003eOutput capability: It can control devices within 30v5A or within 220v5A\u003cbr data-mce-fragment=\"1\"\u003eQuiescent current: 20mA, working current: 50mA\u003cbr data-mce-fragment=\"1\"\u003eService life: more than 100,000 times;\u003cbr data-mce-fragment=\"1\"\u003eWorking temperature: -40~85 °C;\u003cbr data-mce-fragment=\"1\"\u003eNet weight: about 26g\u003cbr data-mce-fragment=\"1\"\u003eSize: 64.2mm*34.8mm*18.5mm\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eFeatures\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eVoltage input anti-reverse circuit, worry-free wiring. Signal input optocoupler isolation, strong anti-interference ability. Set the parameter to power off permanent memory. Powerful flash MCU online programming function, according to user needs can contact the manufacturer to customize the required functions.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eWiring diagram\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cimg src=\"https:\/\/pg-cdn-a2.datacaciques.com\/00\/NDAy\/19\/08\/21\/02s76nl1201bce4t\/76050b0dfcc5297c.jpg\" data-mce-fragment=\"1\" data-mce-src=\"https:\/\/pg-cdn-a2.datacaciques.com\/00\/NDAy\/19\/08\/21\/02s76nl1201bce4t\/76050b0dfcc5297c.jpg\"\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eFunction introduction\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eP-1: The signal triggers the relay to pull in. When the time is up, the relay is disconnected during the delay.\u003cbr data-mce-fragment=\"1\"\u003eA: Invalid trigger again B: Re-trigger re-clocking C: Trigger relay reset again to stop timing\u003cbr data-mce-fragment=\"1\"\u003eP-2: The signal trigger start timing time T1, the time is up to the relay pull-in time T2 is disconnected (reset)\u003cbr data-mce-fragment=\"1\"\u003eA: Invalid trigger again B: Re-trigger re-clocking C: Start delay without triggering power-on\u003cbr data-mce-fragment=\"1\"\u003eP-3: Cycling: Turn on T1, disconnect T2, infinite loop. For T1 and T2, the time is adjustable; if a parameter is turned ON or OFF, it can be turned on or the power is turned on.\u003cbr data-mce-fragment=\"1\"\u003eA: The relay is turned on immediately after power-on. B: The relay is turned off and then turned on after power-on.\u003cbr data-mce-fragment=\"1\"\u003eP-4: There is signal, the relay is closed, the suction is kept, the signal disappears, the timing starts, the time is up, the relay is disconnected, during the delay, the signal is given again, the delay is cancelled, the relay is kept, the signal disappears, and the time is re-timed.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cstrong data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eNotes\u003c\/span\u003e\u003c\/strong\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eThe relay output is a passive contact that has no live output and controls the on\/off of a line.\u003c\/span\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e\u003cspan face=\"helveticao\" data-mce-fragment=\"1\"\u003e3.Digital Display Delay Controller:(DC 12V with Buzzer 3 Button)\u003c\/span\u003e\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan face=\"helveticao\" data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eProduct parameters\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eWorking voltage: DC12V (normal working voltage DC10V-16V)\u003cbr data-mce-fragment=\"1\"\u003eSource: DC4V~20V (usual power supply positive trigger, button, PNP sensor, PLC signal, etc.)\u003cbr data-mce-fragment=\"1\"\u003eOutput capability: It can control devices within 30v5A or within 220v5A\u003cbr data-mce-fragment=\"1\"\u003eQuiescent current: 20mA, working current: 50mA\u003cbr data-mce-fragment=\"1\"\u003eService life: more than 100,000 times;\u003cbr data-mce-fragment=\"1\"\u003eWorking temperature: -40~85 °C;\u003cbr data-mce-fragment=\"1\"\u003eNet weight: about 26g\u003cbr data-mce-fragment=\"1\"\u003eSize: 64.2mm*34.8mm*18.5mm\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eFeatures\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003ePower input flash-coupled, strong-interference ability. Power of flash MCU online programming function, according to user needs can contact the manufacturer to customize the Required functions.\u003c\/span\u003e\u003cspan face=\"helveticao\" data-mce-fragment=\"1\"\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003c\/span\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003eFunction introduction\u003cbr data-mce-fragment=\"1\"\u003eP-1: The trigger signal is received, the relay is turned on, the timer expires, and the relay is turned off.\u003cbr data-mce-fragment=\"1\"\u003eA1: Invalid again during delayed trigger\u003cbr data-mce-fragment=\"1\"\u003eA2: Trigger again during retiming delay\u003cbr data-mce-fragment=\"1\"\u003eA3: During the delay trigger, the trigger signal is received again to terminate the current delay.\u003cbr data-mce-fragment=\"1\"\u003eP-2: Receive trigger signal, X start time, relay off, Y start time, relay open\u003cbr data-mce-fragment=\"1\"\u003eP-3: Cycle switching mode\u003cbr data-mce-fragment=\"1\"\u003eA1: After the power relay is turned on, the timing is turned off and the loop is infinite.\u003cbr data-mce-fragment=\"1\"\u003eA2: After the power relay is turned off, the timing ends and the loop is infinite.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cstrong data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eNotes:\u003c\/span\u003e\u003c\/strong\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eThe relay output is a passive contact that has no live output and controls the on\/off of a line.\u003c\/span\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e4.Dual MOS delay control board: (DC 5-30V 4 Button)\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eDescription:\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003eDual MOS parallel active output, lower internal resistance, larger current, strong power interface, clear and simple, powerful, one-button emergency stop function (STOP button), with reverse connection protection, reverse connection, no burning, power-off memory. Increase Sleep mode, after enabling, no operation within 5 minutes, automatically turn off the display, wake up any button! You can set different OP, CL, LOP parameters, these parameters are independent of each other, save the setting parameters automatically power-down save and other functions, Almost all the needs!\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eProduct manual\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eWorking voltage: DC5V-DC30V (wide voltage anti-connection protection)\u003cbr data-mce-fragment=\"1\"\u003eTrigger signal source: high-level trigger DC 3.0V—24V signal ground and system ground to improve the system's anti-interference ability can also short-circuit the ground\u003cbr data-mce-fragment=\"1\"\u003eOutput capacity: DC DC 5V--36V, continuous current 15A at normal temperature, power 400W! Under the condition of auxiliary heat dissipation, the maximum current can reach 30A\u003cbr data-mce-fragment=\"1\"\u003eProduct size: 64mm*35mm*19.3mm\u003cbr data-mce-fragment=\"1\"\u003eMounting hole: diameter 3mm\u003cbr data-mce-fragment=\"1\"\u003eWorking temperature: -40 ° C ~ 85 ° C\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eOperating mode\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eP1 mode: After the signal is triggered, the MOS transistor turns on the OP time and then turns off; in the OP time, the following operation\u003cbr data-mce-fragment=\"1\"\u003eP1.1: The signal is triggered again.\u003cbr data-mce-fragment=\"1\"\u003eP1.2: Signal triggers re-timed again\u003cbr data-mce-fragment=\"1\"\u003eP1.3: The signal triggers reset again, the MOS tube is disconnected, and the timing is stopped.\u003cbr data-mce-fragment=\"1\"\u003eP-2: Give the trigger signal, after the MOS transistor is disconnected from the CL time, the MOS transistor turns on the OP time. After the timing is completed, the MOS transistor is disconnected.\u003cbr data-mce-fragment=\"1\"\u003eP3.1: Give the trigger signal, after the MOS transistor turns on the OP time, the MOS tube turns off the CL time, then loops the above action, the signal is given again in the loop, the MOS tube is disconnected, the timing is stopped; the number of cycles (LOP) can be set.\u003cbr data-mce-fragment=\"1\"\u003eP3.2: No need to trigger signal after power-on, MOS tube turns on OP time, MOS tube disconnects CL time, loops the above action; loop number (LOP) can be set\u003cbr data-mce-fragment=\"1\"\u003eP-4: Signal hold function If there is a trigger signal, the timing is cleared, the MOS transistor remains on; when the signal disappears, the MOS transistor is disconnected after timing the OP; during the timing, there is a signal and the timing is cleared.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eRelay enable mode\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eON : MOS tube is allowed to conduct during OP conduction time\u003cbr data-mce-fragment=\"1\"\u003eOFF : MOS tube is disabled, always off\u003cbr data-mce-fragment=\"1\"\u003eShort press the STOP button on the main interface to switch between ON and OFF. The current state will flash, then return to the main interface. This function is the emergency stop function. One button is used to open and close the MOS tube.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eSleep mode (long press the stop button to view the current mode)\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eC-P sleep mode: within five minutes, without any operation, the digital tube automatically turns off the display, the program runs normally.\u003cbr data-mce-fragment=\"1\"\u003eO-d normal mode: the digital tube is always on display\u003cbr data-mce-fragment=\"1\"\u003ePress and hold the STOP button for 2 seconds and then release to switch the C-P and O-d states. The current state will flash and then return to the main interface.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eTiming range\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eHow to choose the timing range\u003cbr data-mce-fragment=\"1\"\u003e1).After setting the parameter value in the mode selection interface, press the STOP button to select the timing range.\u003cbr data-mce-fragment=\"1\"\u003eXXX. Decimal point is in one place, timing range: 1 second to 999 seconds\u003cbr data-mce-fragment=\"1\"\u003eXX.X decimal point in ten, timing range: 0.1 seconds to 99.9 seconds\u003cbr data-mce-fragment=\"1\"\u003eX.X.X. The decimal point is fully illuminated, the timing range is from 1 minute to 999 minutes.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e2).For example, if you want to set the OP to 3.2 seconds, move the decimal point to ten digits, and the digital tube displays 03.2.\u003cbr data-mce-fragment=\"1\"\u003eParameter description: OP on time, CL off time, LOP cycle number 1-999 times, \"---\" stands for infinite loop.\u003cbr data-mce-fragment=\"1\"\u003eThese parameters are independent of each other, but each mode shares these parameters. For example, when the on-time OP is set to 5 seconds in P1.1, the user wants to switch to the P1.2 mode, then when entering the P1.2 setting corresponding parameters, the OP also It will be 5 seconds.\u003cbr data-mce-fragment=\"1\"\u003eDisplaying 000 on the main interface and pressing the SET button will display OPL, LOP and corresponding time XXX\u003cbr data-mce-fragment=\"1\"\u003eIf only OP in the mode, such as mode P1.1, P1.2, P1.3 time, then short press SET button will only display OP and corresponding time.\u003cbr data-mce-fragment=\"1\"\u003eIf the mode has OP, CL, LOP such as mode P3.1, P3.2 short press SET button will display OP and corresponding time, CL and corresponding time, LOP and corresponding times.\u003cbr data-mce-fragment=\"1\"\u003eAfter setting the mode, it is very convenient to easily check the parameters set in the current mode by pressing the SET button on the main interface.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eHow to set parameters\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e1) First determine the working mode of the MOS tube\u003cbr data-mce-fragment=\"1\"\u003eAccording to the working mode of the MOS tube, in the main interface (when the module is powered on, it will flash the current working mode (default P1.1 mode), then enter the main interface \"press and hold the SET button for 2 seconds and then release\" to enter the mode. Select the interface, press the UP, DOWN button to select the mode to be set P1.1~P-4\u003cbr data-mce-fragment=\"1\"\u003e2) After selecting the mode to be set (for example, P3.2), press the SET button to set the corresponding parameter. At this time, the parameter to be set will flash OP ON time, CL OFF time, LOP cycle number “---” Represents an infinite loop, adjusts the parameter value through UP and DOWN, supports long press (rapid increase or decrease) and short press (increase or decrease 1 unit); after setting the parameter value, select the decimal point position by short pressing the STOP button. , select the timing range (corresponding time 0.1 seconds ~ 999 minutes); short press the SET button to set the next parameter of the current mode, the process is the same as above.\u003cbr data-mce-fragment=\"1\"\u003e3) After setting the parameters of the selected mode, press and hold the SET button for 2 seconds to release, the currently set mode will flash, then return to the main interface and set the parameters successfully.\u003cbr data-mce-fragment=\"1\"\u003e4) Main interface: “000” (no decimal point) is displayed when the MOS tube is not working, and the MOS tube has a decimal point in the working state.\u003cbr data-mce-fragment=\"1\"\u003e5) Mode selection interface: long press SET button to enter, after setting is completed, long press SET button to exit, return to the main interface\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cstrong data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eNote:\u003c\/span\u003e\u003c\/strong\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eThe module is an active live output, and the voltage at the output (load) is equal to the input voltage DC\u003c\/span\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e5.USD Digital Display Delay Controller: ( DC12V 4 Button )\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eDescription:\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003eThis relay delay control board has a powerful and clear interface, powerful function, one-button emergency stop function (STOP button), with reverse connection protection, reverse connection without burning, power-off memory. Increased sleep mode, after enabling, No operation within 5 minutes, automatically turn off the display, wake up any button! You can set different OP, CL, LOP parameters, these parameters are independent of each other, save the setting parameters automatically power-down save and other functions, almost meet all needs!\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eProduct manual:\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eWorking voltage: DC6V-DC30V (wide voltage anti-connection protection)\u003cbr data-mce-fragment=\"1\"\u003eTrigger signal source: high-level trigger DC 3.0V—24V signal ground and system ground to improve the system's anti-interference ability can also short-circuit the ground\u003cbr data-mce-fragment=\"1\"\u003eOutput capacity: controllable DC 30V\/10A or AC 250V\/10A equipment\u003cbr data-mce-fragment=\"1\"\u003eProduct size: 64mm*35mm*19.3mm\u003cbr data-mce-fragment=\"1\"\u003eMounting hole: diameter 3mm\u003cbr data-mce-fragment=\"1\"\u003eWorking temperature: -40 ° C ~ 85 ° C\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e6.DC Motor Speed Controller :(DC 8-55V Motor Speed Controller )\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eDescription:\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003eThis product brings together a wide range of modern motor speed control, with the advantages of small size, simple operation, high current resistance and reverse connection. Suitable for most users in various environments with various speeds, support acceleration and deceleration functions can be set through the menu, with set parameters power off permanent memory function\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eProduct manual:\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eVoltage: DC8V-55V (wide voltage anti-back protection)\u003cbr data-mce-fragment=\"1\"\u003eSpeed range: long press \/ short press to adjust the degree, 0% -100% speed\u003cbr data-mce-fragment=\"1\"\u003eDrive current: up to 10A, (recommended output series 12A fuse)\u003cbr data-mce-fragment=\"1\"\u003eStandby current: \u0026lt;17mA\u003cbr data-mce-fragment=\"1\"\u003eMounting hole: diameter 3mm\u003cbr data-mce-fragment=\"1\"\u003eProduct size: 64mm*35mm*19mm (length * width * height)\u003cbr data-mce-fragment=\"1\"\u003eWorking temperature: -20 ° C ~ 70 ° C\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eInstructions:\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e1. Click\/long press the “speed increase” button to increase the motor speed to 100%.\u003cbr data-mce-fragment=\"1\"\u003e2. Click\/long press the “speed down” button to increase the motor speed to a minimum of 0%.\u003cbr data-mce-fragment=\"1\"\u003e3. Press and hold the “Power On\/Off” button for one second, the controller will be turned on or off (the power is turned off by default, and the memory function is activated after booting)\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003ePrecautions:\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e1. The digital tube flashes at the moment of power-on (normal phenomenon, no need to worry)\u003cbr data-mce-fragment=\"1\"\u003e2, close to the limit drive current working conditions, it is recommended to take the output end of the fuse\u003cbr data-mce-fragment=\"1\"\u003e3. The DC motor speed controller cannot be installed in places where there is dripping water and children can reach it.\u003cbr data-mce-fragment=\"1\"\u003e4. After wiring, check if the line is correct and then energize, so as to avoid accidentally burning the temperature controller and load device.\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003eWiring:\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e“M+” and “M-” are respectively connected to the positive and negative terminals of the output, M+ is positive and M- is negative.\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e“VIN” and “GND” are respectively connected to the positive and negative terminals of the input terminal, Vin is positive and GND is negative (input power supply voltage is DC8V-55V)\u003c\/span\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e7.Temperature Controller:(DC 12V Temperrature Controller)\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eProduct Parameters:\u003c\/span\u003e\u003c\/strong\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003eControl range: -50~110°C\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eResolution: -9.9~99.9, 0.1°C, other temperature range, 1°C\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eTemperature measurement accuracy: 0.1 °C\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eControl accuracy: 0.1 ° C\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eHysteresis accuracy: 0.1 ° C\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eRefresh rate: 0.5S\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eHigh temperature alarm: 0-110 °C\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eMeasurement input: NTC (10K0.5%) waterproof sensor\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eOutput: One way 10A relay\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eEnvironmental requirements: Temperature -10~60°C Humidity 20%-85%\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eSize: 48*40mm\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003ePower consumption of the whole machine: quiescent current: ≤35MA, Pull-in current: ≤65MA\u003c\/span\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eSetting Parameter Method:\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eOnce the power supply and load are connected, the control can be powered. After power-on, the digital tube displays the current real-time temperature. Press the SET button briefly, the digital tube displays the temperature flashing, press the + - button to adjust the set temperature; after the adjustment is completed, press the SET button to save the set temperature and return. At this time, the controller automatically Execute the relay on and off; press and hold the SET button for 5 seconds to enter the menu parameter setting, short press the + - button to switch P0...P6, short press the SET button to enter the menu.\u003cbr data-mce-fragment=\"1\"\u003eThe thermostat output is a 10A relay to meet a variety of high power loads, please ensure that the line is correct.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eIndicator light, digital tube status description:\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eIndicator light: Off means the relay is off, steady light means the relay is closed\u003cbr data-mce-fragment=\"1\"\u003eDigital tube: Display LLL for sensor open circuit: Display HHH is out of measurement range. The thermostat will forcibly open the relay.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eParameter Function Description:\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003ctable data-mce-fragment=\"1\"\u003e\n\u003ctbody data-mce-fragment=\"1\"\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eMenu identifier\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eMenu function\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003ePredetermined area\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eFactory setting\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eP0\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eRefrigeration C \/ Heating H\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eC\/H\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eC\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eP1\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eBacklash\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e0.1-15\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e2.0\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eP2\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eMaximum set temperature\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e-50~110℃\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e110\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eP3\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eMinimum set temperature\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e-50~110℃\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e-50\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eP4\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eTemperature correction\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e-7.0~7.0℃\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e0.0\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eP5\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003ePress delay\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e0-10 minutes\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e0\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eP6\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eHigh temperature alarm\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eON\/OFF\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003eOFF\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003ePackage Included:\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e1PC*DC 12V 2\/3\/4 Button Time Delay Relay Motor Speed Temperrature Controller+Buzzer\u003cstrong data-mce-fragment=\"1\"\u003e(According to your choice)\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e"}
-
Translation missing: en.products.product.regular_price $8.99{"id":6086411911368,"title":"5V\/12V 2\/3\/4 Button Timer Delay Relay Motor Speed Temperature Controller+Buzzer","handle":"5v-12v-2-3-4-button-timer-delay-relay-motor-speed-temperature-controller-buzzer","description":"\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e1.Digital Display Delay Controller:(DC 12V with Buzzer 2 Button\u003cspan face=\"helveticao\" data-mce-fragment=\"1\"\u003e)\u003c\/span\u003e\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eProduct parameters\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\n\u003cul data-mce-fragment=\"1\"\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eWorking voltage: DC12V (normal working voltage DC10V-16V)\u003c\/span\u003e\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eSignal source: DC4V~20V (usual power supply positive trigger, button, PNP sensor, PLC signal, etc.)\u003c\/span\u003e\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eOutput capability: It can control devices within 30v5A or within 220v5A\u003c\/span\u003e\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eQuiescent current: 20mA, working current: 50mA\u003c\/span\u003e\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eService life: more than 100,000 times;\u003c\/span\u003e\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eWorking temperature: -40~85 °C;\u003c\/span\u003e\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eNet weight: about 26g\u003c\/span\u003e\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eSize: 64.2mm*34.8mm*18.5mm\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eFeatures\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\n\u003cul data-mce-fragment=\"1\"\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eVoltage input anti-reverse circuit, worry-free wiring. Signal input optocoupler isolation, strong anti-interference ability. Set the parameter to power off permanent memory. Powerful flash MCU online programming function, according to user needs can contact the manufacturer to customize the required functions.\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eFunction introduction\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\n\u003cul data-mce-fragment=\"1\"\u003e\n\u003cli data-mce-fragment=\"1\"\u003eWhen the power is turned on, the trigger signal is received, the countdown starts, and the relay works. When the timer ends, the relay stops working, the time returns to the setting, and the next trigger signal is waited.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eInstructions\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cul data-mce-fragment=\"1\"\u003e\n\u003cli data-mce-fragment=\"1\"\u003e1).Press K1 to enter the time setting, the hundred digit digital tube starts to flash; press K2 at this time, the hundred digits change; press K1 again, the ten digital tube starts to flash; press K2 at this time, the ten digits change; press again After K1, the digital tube starts to flash. At this time, press K2, the digit of the digit changes; press K1 again to exit the setting, and the digital tube no longer flashes.\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003e2).When the digital tube is normally displayed, press K2, the decimal point is shifted, the decimal point is 0 to 999 seconds in ones digit, the decimal point is 0 to 99.9 seconds in ten digits, and the decimal point is 0 to 999 minutes; the time is set.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e2.Digital Display Delay Controller:(DC 12V 3 Button)\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eProduct parameters\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eWorking voltage: DC12V (normal working voltage DC10V-16V)\u003cbr data-mce-fragment=\"1\"\u003eSource: DC4V~20V (usual power supply positive trigger, button, PNP sensor, PLC signal, etc.)\u003cbr data-mce-fragment=\"1\"\u003eOutput capability: It can control devices within 30v5A or within 220v5A\u003cbr data-mce-fragment=\"1\"\u003eQuiescent current: 20mA, working current: 50mA\u003cbr data-mce-fragment=\"1\"\u003eService life: more than 100,000 times;\u003cbr data-mce-fragment=\"1\"\u003eWorking temperature: -40~85 °C;\u003cbr data-mce-fragment=\"1\"\u003eNet weight: about 26g\u003cbr data-mce-fragment=\"1\"\u003eSize: 64.2mm*34.8mm*18.5mm\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eFeatures\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eVoltage input anti-reverse circuit, worry-free wiring. Signal input optocoupler isolation, strong anti-interference ability. Set the parameter to power off permanent memory. Powerful flash MCU online programming function, according to user needs can contact the manufacturer to customize the required functions.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eWiring diagram\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cimg src=\"https:\/\/pg-cdn-a2.datacaciques.com\/00\/NDAy\/19\/08\/21\/02s76nl1201bce4t\/76050b0dfcc5297c.jpg\" data-mce-fragment=\"1\" data-mce-src=\"https:\/\/pg-cdn-a2.datacaciques.com\/00\/NDAy\/19\/08\/21\/02s76nl1201bce4t\/76050b0dfcc5297c.jpg\"\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eFunction introduction\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eP-1: The signal triggers the relay to pull in. When the time is up, the relay is disconnected during the delay.\u003cbr data-mce-fragment=\"1\"\u003eA: Invalid trigger again B: Re-trigger re-clocking C: Trigger relay reset again to stop timing\u003cbr data-mce-fragment=\"1\"\u003eP-2: The signal trigger start timing time T1, the time is up to the relay pull-in time T2 is disconnected (reset)\u003cbr data-mce-fragment=\"1\"\u003eA: Invalid trigger again B: Re-trigger re-clocking C: Start delay without triggering power-on\u003cbr data-mce-fragment=\"1\"\u003eP-3: Cycling: Turn on T1, disconnect T2, infinite loop. For T1 and T2, the time is adjustable; if a parameter is turned ON or OFF, it can be turned on or the power is turned on.\u003cbr data-mce-fragment=\"1\"\u003eA: The relay is turned on immediately after power-on. B: The relay is turned off and then turned on after power-on.\u003cbr data-mce-fragment=\"1\"\u003eP-4: There is signal, the relay is closed, the suction is kept, the signal disappears, the timing starts, the time is up, the relay is disconnected, during the delay, the signal is given again, the delay is cancelled, the relay is kept, the signal disappears, and the time is re-timed.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cstrong data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eNotes\u003c\/span\u003e\u003c\/strong\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eThe relay output is a passive contact that has no live output and controls the on\/off of a line.\u003c\/span\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e\u003cspan face=\"helveticao\" data-mce-fragment=\"1\"\u003e3.Digital Display Delay Controller:(DC 12V with Buzzer 3 Button)\u003c\/span\u003e\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan face=\"helveticao\" data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eProduct parameters\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eWorking voltage: DC12V (normal working voltage DC10V-16V)\u003cbr data-mce-fragment=\"1\"\u003eSource: DC4V~20V (usual power supply positive trigger, button, PNP sensor, PLC signal, etc.)\u003cbr data-mce-fragment=\"1\"\u003eOutput capability: It can control devices within 30v5A or within 220v5A\u003cbr data-mce-fragment=\"1\"\u003eQuiescent current: 20mA, working current: 50mA\u003cbr data-mce-fragment=\"1\"\u003eService life: more than 100,000 times;\u003cbr data-mce-fragment=\"1\"\u003eWorking temperature: -40~85 °C;\u003cbr data-mce-fragment=\"1\"\u003eNet weight: about 26g\u003cbr data-mce-fragment=\"1\"\u003eSize: 64.2mm*34.8mm*18.5mm\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eFeatures\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003ePower input flash-coupled, strong-interference ability. Power of flash MCU online programming function, according to user needs can contact the manufacturer to customize the Required functions.\u003c\/span\u003e\u003cspan face=\"helveticao\" data-mce-fragment=\"1\"\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003c\/span\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003eFunction introduction\u003cbr data-mce-fragment=\"1\"\u003eP-1: The trigger signal is received, the relay is turned on, the timer expires, and the relay is turned off.\u003cbr data-mce-fragment=\"1\"\u003eA1: Invalid again during delayed trigger\u003cbr data-mce-fragment=\"1\"\u003eA2: Trigger again during retiming delay\u003cbr data-mce-fragment=\"1\"\u003eA3: During the delay trigger, the trigger signal is received again to terminate the current delay.\u003cbr data-mce-fragment=\"1\"\u003eP-2: Receive trigger signal, X start time, relay off, Y start time, relay open\u003cbr data-mce-fragment=\"1\"\u003eP-3: Cycle switching mode\u003cbr data-mce-fragment=\"1\"\u003eA1: After the power relay is turned on, the timing is turned off and the loop is infinite.\u003cbr data-mce-fragment=\"1\"\u003eA2: After the power relay is turned off, the timing ends and the loop is infinite.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cstrong data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eNotes:\u003c\/span\u003e\u003c\/strong\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eThe relay output is a passive contact that has no live output and controls the on\/off of a line.\u003c\/span\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e4.Dual MOS delay control board: (DC 5-30V 4 Button)\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eDescription:\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003eDual MOS parallel active output, lower internal resistance, larger current, strong power interface, clear and simple, powerful, one-button emergency stop function (STOP button), with reverse connection protection, reverse connection, no burning, power-off memory. Increase Sleep mode, after enabling, no operation within 5 minutes, automatically turn off the display, wake up any button! You can set different OP, CL, LOP parameters, these parameters are independent of each other, save the setting parameters automatically power-down save and other functions, Almost all the needs!\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eProduct manual\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eWorking voltage: DC5V-DC30V (wide voltage anti-connection protection)\u003cbr data-mce-fragment=\"1\"\u003eTrigger signal source: high-level trigger DC 3.0V—24V signal ground and system ground to improve the system's anti-interference ability can also short-circuit the ground\u003cbr data-mce-fragment=\"1\"\u003eOutput capacity: DC DC 5V--36V, continuous current 15A at normal temperature, power 400W! Under the condition of auxiliary heat dissipation, the maximum current can reach 30A\u003cbr data-mce-fragment=\"1\"\u003eProduct size: 64mm*35mm*19.3mm\u003cbr data-mce-fragment=\"1\"\u003eMounting hole: diameter 3mm\u003cbr data-mce-fragment=\"1\"\u003eWorking temperature: -40 ° C ~ 85 ° C\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eOperating mode\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eP1 mode: After the signal is triggered, the MOS transistor turns on the OP time and then turns off; in the OP time, the following operation\u003cbr data-mce-fragment=\"1\"\u003eP1.1: The signal is triggered again.\u003cbr data-mce-fragment=\"1\"\u003eP1.2: Signal triggers re-timed again\u003cbr data-mce-fragment=\"1\"\u003eP1.3: The signal triggers reset again, the MOS tube is disconnected, and the timing is stopped.\u003cbr data-mce-fragment=\"1\"\u003eP-2: Give the trigger signal, after the MOS transistor is disconnected from the CL time, the MOS transistor turns on the OP time. After the timing is completed, the MOS transistor is disconnected.\u003cbr data-mce-fragment=\"1\"\u003eP3.1: Give the trigger signal, after the MOS transistor turns on the OP time, the MOS tube turns off the CL time, then loops the above action, the signal is given again in the loop, the MOS tube is disconnected, the timing is stopped; the number of cycles (LOP) can be set.\u003cbr data-mce-fragment=\"1\"\u003eP3.2: No need to trigger signal after power-on, MOS tube turns on OP time, MOS tube disconnects CL time, loops the above action; loop number (LOP) can be set\u003cbr data-mce-fragment=\"1\"\u003eP-4: Signal hold function If there is a trigger signal, the timing is cleared, the MOS transistor remains on; when the signal disappears, the MOS transistor is disconnected after timing the OP; during the timing, there is a signal and the timing is cleared.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eRelay enable mode\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eON : MOS tube is allowed to conduct during OP conduction time\u003cbr data-mce-fragment=\"1\"\u003eOFF : MOS tube is disabled, always off\u003cbr data-mce-fragment=\"1\"\u003eShort press the STOP button on the main interface to switch between ON and OFF. The current state will flash, then return to the main interface. This function is the emergency stop function. One button is used to open and close the MOS tube.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eSleep mode (long press the stop button to view the current mode)\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eC-P sleep mode: within five minutes, without any operation, the digital tube automatically turns off the display, the program runs normally.\u003cbr data-mce-fragment=\"1\"\u003eO-d normal mode: the digital tube is always on display\u003cbr data-mce-fragment=\"1\"\u003ePress and hold the STOP button for 2 seconds and then release to switch the C-P and O-d states. The current state will flash and then return to the main interface.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eTiming range\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eHow to choose the timing range\u003cbr data-mce-fragment=\"1\"\u003e1).After setting the parameter value in the mode selection interface, press the STOP button to select the timing range.\u003cbr data-mce-fragment=\"1\"\u003eXXX. Decimal point is in one place, timing range: 1 second to 999 seconds\u003cbr data-mce-fragment=\"1\"\u003eXX.X decimal point in ten, timing range: 0.1 seconds to 99.9 seconds\u003cbr data-mce-fragment=\"1\"\u003eX.X.X. The decimal point is fully illuminated, the timing range is from 1 minute to 999 minutes.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e2).For example, if you want to set the OP to 3.2 seconds, move the decimal point to ten digits, and the digital tube displays 03.2.\u003cbr data-mce-fragment=\"1\"\u003eParameter description: OP on time, CL off time, LOP cycle number 1-999 times, \"---\" stands for infinite loop.\u003cbr data-mce-fragment=\"1\"\u003eThese parameters are independent of each other, but each mode shares these parameters. For example, when the on-time OP is set to 5 seconds in P1.1, the user wants to switch to the P1.2 mode, then when entering the P1.2 setting corresponding parameters, the OP also It will be 5 seconds.\u003cbr data-mce-fragment=\"1\"\u003eDisplaying 000 on the main interface and pressing the SET button will display OPL, LOP and corresponding time XXX\u003cbr data-mce-fragment=\"1\"\u003eIf only OP in the mode, such as mode P1.1, P1.2, P1.3 time, then short press SET button will only display OP and corresponding time.\u003cbr data-mce-fragment=\"1\"\u003eIf the mode has OP, CL, LOP such as mode P3.1, P3.2 short press SET button will display OP and corresponding time, CL and corresponding time, LOP and corresponding times.\u003cbr data-mce-fragment=\"1\"\u003eAfter setting the mode, it is very convenient to easily check the parameters set in the current mode by pressing the SET button on the main interface.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eHow to set parameters\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e1) First determine the working mode of the MOS tube\u003cbr data-mce-fragment=\"1\"\u003eAccording to the working mode of the MOS tube, in the main interface (when the module is powered on, it will flash the current working mode (default P1.1 mode), then enter the main interface \"press and hold the SET button for 2 seconds and then release\" to enter the mode. Select the interface, press the UP, DOWN button to select the mode to be set P1.1~P-4\u003cbr data-mce-fragment=\"1\"\u003e2) After selecting the mode to be set (for example, P3.2), press the SET button to set the corresponding parameter. At this time, the parameter to be set will flash OP ON time, CL OFF time, LOP cycle number “---” Represents an infinite loop, adjusts the parameter value through UP and DOWN, supports long press (rapid increase or decrease) and short press (increase or decrease 1 unit); after setting the parameter value, select the decimal point position by short pressing the STOP button. , select the timing range (corresponding time 0.1 seconds ~ 999 minutes); short press the SET button to set the next parameter of the current mode, the process is the same as above.\u003cbr data-mce-fragment=\"1\"\u003e3) After setting the parameters of the selected mode, press and hold the SET button for 2 seconds to release, the currently set mode will flash, then return to the main interface and set the parameters successfully.\u003cbr data-mce-fragment=\"1\"\u003e4) Main interface: “000” (no decimal point) is displayed when the MOS tube is not working, and the MOS tube has a decimal point in the working state.\u003cbr data-mce-fragment=\"1\"\u003e5) Mode selection interface: long press SET button to enter, after setting is completed, long press SET button to exit, return to the main interface\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cstrong data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eNote:\u003c\/span\u003e\u003c\/strong\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eThe module is an active live output, and the voltage at the output (load) is equal to the input voltage DC\u003c\/span\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e5.USD Digital Display Delay Controller: ( DC12V 4 Button )\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eDescription:\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003eThis relay delay control board has a powerful and clear interface, powerful function, one-button emergency stop function (STOP button), with reverse connection protection, reverse connection without burning, power-off memory. Increased sleep mode, after enabling, No operation within 5 minutes, automatically turn off the display, wake up any button! You can set different OP, CL, LOP parameters, these parameters are independent of each other, save the setting parameters automatically power-down save and other functions, almost meet all needs!\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eProduct manual:\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eWorking voltage: DC6V-DC30V (wide voltage anti-connection protection)\u003cbr data-mce-fragment=\"1\"\u003eTrigger signal source: high-level trigger DC 3.0V—24V signal ground and system ground to improve the system's anti-interference ability can also short-circuit the ground\u003cbr data-mce-fragment=\"1\"\u003eOutput capacity: controllable DC 30V\/10A or AC 250V\/10A equipment\u003cbr data-mce-fragment=\"1\"\u003eProduct size: 64mm*35mm*19.3mm\u003cbr data-mce-fragment=\"1\"\u003eMounting hole: diameter 3mm\u003cbr data-mce-fragment=\"1\"\u003eWorking temperature: -40 ° C ~ 85 ° C\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e6.DC Motor Speed Controller :(DC 8-55V Motor Speed Controller )\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eDescription:\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003eThis product brings together a wide range of modern motor speed control, with the advantages of small size, simple operation, high current resistance and reverse connection. Suitable for most users in various environments with various speeds, support acceleration and deceleration functions can be set through the menu, with set parameters power off permanent memory function\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eProduct manual:\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eVoltage: DC8V-55V (wide voltage anti-back protection)\u003cbr data-mce-fragment=\"1\"\u003eSpeed range: long press \/ short press to adjust the degree, 0% -100% speed\u003cbr data-mce-fragment=\"1\"\u003eDrive current: up to 10A, (recommended output series 12A fuse)\u003cbr data-mce-fragment=\"1\"\u003eStandby current: \u0026lt;17mA\u003cbr data-mce-fragment=\"1\"\u003eMounting hole: diameter 3mm\u003cbr data-mce-fragment=\"1\"\u003eProduct size: 64mm*35mm*19mm (length * width * height)\u003cbr data-mce-fragment=\"1\"\u003eWorking temperature: -20 ° C ~ 70 ° C\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eInstructions:\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e1. Click\/long press the “speed increase” button to increase the motor speed to 100%.\u003cbr data-mce-fragment=\"1\"\u003e2. Click\/long press the “speed down” button to increase the motor speed to a minimum of 0%.\u003cbr data-mce-fragment=\"1\"\u003e3. Press and hold the “Power On\/Off” button for one second, the controller will be turned on or off (the power is turned off by default, and the memory function is activated after booting)\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003ePrecautions:\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e1. The digital tube flashes at the moment of power-on (normal phenomenon, no need to worry)\u003cbr data-mce-fragment=\"1\"\u003e2, close to the limit drive current working conditions, it is recommended to take the output end of the fuse\u003cbr data-mce-fragment=\"1\"\u003e3. The DC motor speed controller cannot be installed in places where there is dripping water and children can reach it.\u003cbr data-mce-fragment=\"1\"\u003e4. After wiring, check if the line is correct and then energize, so as to avoid accidentally burning the temperature controller and load device.\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003eWiring:\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e“M+” and “M-” are respectively connected to the positive and negative terminals of the output, M+ is positive and M- is negative.\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e“VIN” and “GND” are respectively connected to the positive and negative terminals of the input terminal, Vin is positive and GND is negative (input power supply voltage is DC8V-55V)\u003c\/span\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e7.Temperature Controller:(DC 12V Temperrature Controller)\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eProduct Parameters:\u003c\/span\u003e\u003c\/strong\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003eControl range: -50~110°C\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eResolution: -9.9~99.9, 0.1°C, other temperature range, 1°C\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eTemperature measurement accuracy: 0.1 °C\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eControl accuracy: 0.1 ° C\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eHysteresis accuracy: 0.1 ° C\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eRefresh rate: 0.5S\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eHigh temperature alarm: 0-110 °C\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eMeasurement input: NTC (10K0.5%) waterproof sensor\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eOutput: One way 10A relay\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eEnvironmental requirements: Temperature -10~60°C Humidity 20%-85%\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eSize: 48*40mm\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003ePower consumption of the whole machine: quiescent current: ≤35MA, Pull-in current: ≤65MA\u003c\/span\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eSetting Parameter Method:\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eOnce the power supply and load are connected, the control can be powered. After power-on, the digital tube displays the current real-time temperature. Press the SET button briefly, the digital tube displays the temperature flashing, press the + - button to adjust the set temperature; after the adjustment is completed, press the SET button to save the set temperature and return. At this time, the controller automatically Execute the relay on and off; press and hold the SET button for 5 seconds to enter the menu parameter setting, short press the + - button to switch P0...P6, short press the SET button to enter the menu.\u003cbr data-mce-fragment=\"1\"\u003eThe thermostat output is a 10A relay to meet a variety of high power loads, please ensure that the line is correct.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eIndicator light, digital tube status description:\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eIndicator light: Off means the relay is off, steady light means the relay is closed\u003cbr data-mce-fragment=\"1\"\u003eDigital tube: Display LLL for sensor open circuit: Display HHH is out of measurement range. The thermostat will forcibly open the relay.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eParameter Function Description:\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003ctable data-mce-fragment=\"1\"\u003e\n\u003ctbody data-mce-fragment=\"1\"\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eMenu identifier\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eMenu function\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003ePredetermined area\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eFactory setting\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eP0\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eRefrigeration C \/ Heating H\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eC\/H\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eC\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eP1\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eBacklash\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e0.1-15\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e2.0\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eP2\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eMaximum set temperature\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e-50~110℃\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e110\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eP3\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eMinimum set temperature\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e-50~110℃\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e-50\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eP4\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eTemperature correction\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e-7.0~7.0℃\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e0.0\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eP5\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003ePress delay\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e0-10 minutes\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e0\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eP6\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eHigh temperature alarm\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eON\/OFF\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003eOFF\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003ePackage Included:\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e1PC*DC 12V 2\/3\/4 Button Time Delay Relay Motor Speed Temperrature Controller+Buzzer\u003cstrong data-mce-fragment=\"1\"\u003e(According to your choice)\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e","published_at":"2020-11-17T14:10:21+08:00","created_at":"2020-11-17T14:10:20+08:00","vendor":"DIYMORE","type":"","tags":[],"price":899,"price_min":899,"price_max":899,"available":true,"price_varies":false,"compare_at_price":null,"compare_at_price_min":0,"compare_at_price_max":0,"compare_at_price_varies":false,"variants":[{"id":37539263873224,"title":"DC 8-55V Motor Speed Controller","option1":"DC 8-55V Motor Speed Controller","option2":null,"option3":null,"sku":"100040","requires_shipping":true,"taxable":false,"featured_image":null,"available":true,"name":"5V\/12V 2\/3\/4 Button Timer Delay Relay Motor Speed Temperature Controller+Buzzer - DC 8-55V Motor Speed Controller","public_title":"DC 8-55V Motor Speed Controller","options":["DC 8-55V Motor Speed Controller"],"price":899,"weight":0,"compare_at_price":null,"inventory_management":"shopify","barcode":"","requires_selling_plan":false,"selling_plan_allocations":[]}],"images":["\/\/www.diymore.cc\/cdn\/shop\/products\/100040_1.jpg?v=1605593426","\/\/www.diymore.cc\/cdn\/shop\/products\/100040_2.jpg?v=1605593426","\/\/www.diymore.cc\/cdn\/shop\/products\/100040.jpg?v=1605593426","\/\/www.diymore.cc\/cdn\/shop\/products\/100040_8.jpg?v=1605593426","\/\/www.diymore.cc\/cdn\/shop\/products\/100040_867e837f-1764-4e74-953c-5a0322a10abe.jpg?v=1605593426","\/\/www.diymore.cc\/cdn\/shop\/products\/100040_7.jpg?v=1605593426","\/\/www.diymore.cc\/cdn\/shop\/products\/100040_4.jpg?v=1605593426","\/\/www.diymore.cc\/cdn\/shop\/products\/100040_5.jpg?v=1605593427","\/\/www.diymore.cc\/cdn\/shop\/products\/100040_6.jpg?v=1605593427","\/\/www.diymore.cc\/cdn\/shop\/products\/100040_3.jpg?v=1605593427"],"featured_image":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040_1.jpg?v=1605593426","options":["Size"],"media":[{"alt":null,"id":14960171581640,"position":1,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040_1.jpg?v=1605593426"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040_1.jpg?v=1605593426","width":1000},{"alt":null,"id":14960171614408,"position":2,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040_2.jpg?v=1605593426"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040_2.jpg?v=1605593426","width":1000},{"alt":null,"id":14960171647176,"position":3,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040.jpg?v=1605593426"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040.jpg?v=1605593426","width":1000},{"alt":null,"id":14960171679944,"position":4,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040_8.jpg?v=1605593426"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040_8.jpg?v=1605593426","width":1000},{"alt":null,"id":14960171712712,"position":5,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040_867e837f-1764-4e74-953c-5a0322a10abe.jpg?v=1605593426"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040_867e837f-1764-4e74-953c-5a0322a10abe.jpg?v=1605593426","width":1000},{"alt":null,"id":14960171745480,"position":6,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040_7.jpg?v=1605593426"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040_7.jpg?v=1605593426","width":1000},{"alt":null,"id":14960171778248,"position":7,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040_4.jpg?v=1605593426"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040_4.jpg?v=1605593426","width":1000},{"alt":null,"id":14960171811016,"position":8,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040_5.jpg?v=1605593427"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040_5.jpg?v=1605593427","width":1000},{"alt":null,"id":14960171843784,"position":9,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040_6.jpg?v=1605593427"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040_6.jpg?v=1605593427","width":1000},{"alt":null,"id":14960171876552,"position":10,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040_3.jpg?v=1605593427"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/100040_3.jpg?v=1605593427","width":1000}],"requires_selling_plan":false,"selling_plan_groups":[],"content":"\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e1.Digital Display Delay Controller:(DC 12V with Buzzer 2 Button\u003cspan face=\"helveticao\" data-mce-fragment=\"1\"\u003e)\u003c\/span\u003e\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eProduct parameters\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\n\u003cul data-mce-fragment=\"1\"\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eWorking voltage: DC12V (normal working voltage DC10V-16V)\u003c\/span\u003e\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eSignal source: DC4V~20V (usual power supply positive trigger, button, PNP sensor, PLC signal, etc.)\u003c\/span\u003e\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eOutput capability: It can control devices within 30v5A or within 220v5A\u003c\/span\u003e\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eQuiescent current: 20mA, working current: 50mA\u003c\/span\u003e\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eService life: more than 100,000 times;\u003c\/span\u003e\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eWorking temperature: -40~85 °C;\u003c\/span\u003e\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eNet weight: about 26g\u003c\/span\u003e\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eSize: 64.2mm*34.8mm*18.5mm\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eFeatures\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\n\u003cul data-mce-fragment=\"1\"\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eVoltage input anti-reverse circuit, worry-free wiring. Signal input optocoupler isolation, strong anti-interference ability. Set the parameter to power off permanent memory. Powerful flash MCU online programming function, according to user needs can contact the manufacturer to customize the required functions.\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eFunction introduction\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\n\u003cul data-mce-fragment=\"1\"\u003e\n\u003cli data-mce-fragment=\"1\"\u003eWhen the power is turned on, the trigger signal is received, the countdown starts, and the relay works. When the timer ends, the relay stops working, the time returns to the setting, and the next trigger signal is waited.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eInstructions\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cul data-mce-fragment=\"1\"\u003e\n\u003cli data-mce-fragment=\"1\"\u003e1).Press K1 to enter the time setting, the hundred digit digital tube starts to flash; press K2 at this time, the hundred digits change; press K1 again, the ten digital tube starts to flash; press K2 at this time, the ten digits change; press again After K1, the digital tube starts to flash. At this time, press K2, the digit of the digit changes; press K1 again to exit the setting, and the digital tube no longer flashes.\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003e2).When the digital tube is normally displayed, press K2, the decimal point is shifted, the decimal point is 0 to 999 seconds in ones digit, the decimal point is 0 to 99.9 seconds in ten digits, and the decimal point is 0 to 999 minutes; the time is set.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e2.Digital Display Delay Controller:(DC 12V 3 Button)\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eProduct parameters\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eWorking voltage: DC12V (normal working voltage DC10V-16V)\u003cbr data-mce-fragment=\"1\"\u003eSource: DC4V~20V (usual power supply positive trigger, button, PNP sensor, PLC signal, etc.)\u003cbr data-mce-fragment=\"1\"\u003eOutput capability: It can control devices within 30v5A or within 220v5A\u003cbr data-mce-fragment=\"1\"\u003eQuiescent current: 20mA, working current: 50mA\u003cbr data-mce-fragment=\"1\"\u003eService life: more than 100,000 times;\u003cbr data-mce-fragment=\"1\"\u003eWorking temperature: -40~85 °C;\u003cbr data-mce-fragment=\"1\"\u003eNet weight: about 26g\u003cbr data-mce-fragment=\"1\"\u003eSize: 64.2mm*34.8mm*18.5mm\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eFeatures\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eVoltage input anti-reverse circuit, worry-free wiring. Signal input optocoupler isolation, strong anti-interference ability. Set the parameter to power off permanent memory. Powerful flash MCU online programming function, according to user needs can contact the manufacturer to customize the required functions.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eWiring diagram\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cimg src=\"https:\/\/pg-cdn-a2.datacaciques.com\/00\/NDAy\/19\/08\/21\/02s76nl1201bce4t\/76050b0dfcc5297c.jpg\" data-mce-fragment=\"1\" data-mce-src=\"https:\/\/pg-cdn-a2.datacaciques.com\/00\/NDAy\/19\/08\/21\/02s76nl1201bce4t\/76050b0dfcc5297c.jpg\"\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eFunction introduction\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eP-1: The signal triggers the relay to pull in. When the time is up, the relay is disconnected during the delay.\u003cbr data-mce-fragment=\"1\"\u003eA: Invalid trigger again B: Re-trigger re-clocking C: Trigger relay reset again to stop timing\u003cbr data-mce-fragment=\"1\"\u003eP-2: The signal trigger start timing time T1, the time is up to the relay pull-in time T2 is disconnected (reset)\u003cbr data-mce-fragment=\"1\"\u003eA: Invalid trigger again B: Re-trigger re-clocking C: Start delay without triggering power-on\u003cbr data-mce-fragment=\"1\"\u003eP-3: Cycling: Turn on T1, disconnect T2, infinite loop. For T1 and T2, the time is adjustable; if a parameter is turned ON or OFF, it can be turned on or the power is turned on.\u003cbr data-mce-fragment=\"1\"\u003eA: The relay is turned on immediately after power-on. B: The relay is turned off and then turned on after power-on.\u003cbr data-mce-fragment=\"1\"\u003eP-4: There is signal, the relay is closed, the suction is kept, the signal disappears, the timing starts, the time is up, the relay is disconnected, during the delay, the signal is given again, the delay is cancelled, the relay is kept, the signal disappears, and the time is re-timed.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cstrong data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eNotes\u003c\/span\u003e\u003c\/strong\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eThe relay output is a passive contact that has no live output and controls the on\/off of a line.\u003c\/span\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e\u003cspan face=\"helveticao\" data-mce-fragment=\"1\"\u003e3.Digital Display Delay Controller:(DC 12V with Buzzer 3 Button)\u003c\/span\u003e\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan face=\"helveticao\" data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eProduct parameters\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eWorking voltage: DC12V (normal working voltage DC10V-16V)\u003cbr data-mce-fragment=\"1\"\u003eSource: DC4V~20V (usual power supply positive trigger, button, PNP sensor, PLC signal, etc.)\u003cbr data-mce-fragment=\"1\"\u003eOutput capability: It can control devices within 30v5A or within 220v5A\u003cbr data-mce-fragment=\"1\"\u003eQuiescent current: 20mA, working current: 50mA\u003cbr data-mce-fragment=\"1\"\u003eService life: more than 100,000 times;\u003cbr data-mce-fragment=\"1\"\u003eWorking temperature: -40~85 °C;\u003cbr data-mce-fragment=\"1\"\u003eNet weight: about 26g\u003cbr data-mce-fragment=\"1\"\u003eSize: 64.2mm*34.8mm*18.5mm\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eFeatures\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003ePower input flash-coupled, strong-interference ability. Power of flash MCU online programming function, according to user needs can contact the manufacturer to customize the Required functions.\u003c\/span\u003e\u003cspan face=\"helveticao\" data-mce-fragment=\"1\"\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003c\/span\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003eFunction introduction\u003cbr data-mce-fragment=\"1\"\u003eP-1: The trigger signal is received, the relay is turned on, the timer expires, and the relay is turned off.\u003cbr data-mce-fragment=\"1\"\u003eA1: Invalid again during delayed trigger\u003cbr data-mce-fragment=\"1\"\u003eA2: Trigger again during retiming delay\u003cbr data-mce-fragment=\"1\"\u003eA3: During the delay trigger, the trigger signal is received again to terminate the current delay.\u003cbr data-mce-fragment=\"1\"\u003eP-2: Receive trigger signal, X start time, relay off, Y start time, relay open\u003cbr data-mce-fragment=\"1\"\u003eP-3: Cycle switching mode\u003cbr data-mce-fragment=\"1\"\u003eA1: After the power relay is turned on, the timing is turned off and the loop is infinite.\u003cbr data-mce-fragment=\"1\"\u003eA2: After the power relay is turned off, the timing ends and the loop is infinite.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cstrong data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eNotes:\u003c\/span\u003e\u003c\/strong\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eThe relay output is a passive contact that has no live output and controls the on\/off of a line.\u003c\/span\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e4.Dual MOS delay control board: (DC 5-30V 4 Button)\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eDescription:\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003eDual MOS parallel active output, lower internal resistance, larger current, strong power interface, clear and simple, powerful, one-button emergency stop function (STOP button), with reverse connection protection, reverse connection, no burning, power-off memory. Increase Sleep mode, after enabling, no operation within 5 minutes, automatically turn off the display, wake up any button! You can set different OP, CL, LOP parameters, these parameters are independent of each other, save the setting parameters automatically power-down save and other functions, Almost all the needs!\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eProduct manual\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eWorking voltage: DC5V-DC30V (wide voltage anti-connection protection)\u003cbr data-mce-fragment=\"1\"\u003eTrigger signal source: high-level trigger DC 3.0V—24V signal ground and system ground to improve the system's anti-interference ability can also short-circuit the ground\u003cbr data-mce-fragment=\"1\"\u003eOutput capacity: DC DC 5V--36V, continuous current 15A at normal temperature, power 400W! Under the condition of auxiliary heat dissipation, the maximum current can reach 30A\u003cbr data-mce-fragment=\"1\"\u003eProduct size: 64mm*35mm*19.3mm\u003cbr data-mce-fragment=\"1\"\u003eMounting hole: diameter 3mm\u003cbr data-mce-fragment=\"1\"\u003eWorking temperature: -40 ° C ~ 85 ° C\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eOperating mode\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eP1 mode: After the signal is triggered, the MOS transistor turns on the OP time and then turns off; in the OP time, the following operation\u003cbr data-mce-fragment=\"1\"\u003eP1.1: The signal is triggered again.\u003cbr data-mce-fragment=\"1\"\u003eP1.2: Signal triggers re-timed again\u003cbr data-mce-fragment=\"1\"\u003eP1.3: The signal triggers reset again, the MOS tube is disconnected, and the timing is stopped.\u003cbr data-mce-fragment=\"1\"\u003eP-2: Give the trigger signal, after the MOS transistor is disconnected from the CL time, the MOS transistor turns on the OP time. After the timing is completed, the MOS transistor is disconnected.\u003cbr data-mce-fragment=\"1\"\u003eP3.1: Give the trigger signal, after the MOS transistor turns on the OP time, the MOS tube turns off the CL time, then loops the above action, the signal is given again in the loop, the MOS tube is disconnected, the timing is stopped; the number of cycles (LOP) can be set.\u003cbr data-mce-fragment=\"1\"\u003eP3.2: No need to trigger signal after power-on, MOS tube turns on OP time, MOS tube disconnects CL time, loops the above action; loop number (LOP) can be set\u003cbr data-mce-fragment=\"1\"\u003eP-4: Signal hold function If there is a trigger signal, the timing is cleared, the MOS transistor remains on; when the signal disappears, the MOS transistor is disconnected after timing the OP; during the timing, there is a signal and the timing is cleared.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eRelay enable mode\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eON : MOS tube is allowed to conduct during OP conduction time\u003cbr data-mce-fragment=\"1\"\u003eOFF : MOS tube is disabled, always off\u003cbr data-mce-fragment=\"1\"\u003eShort press the STOP button on the main interface to switch between ON and OFF. The current state will flash, then return to the main interface. This function is the emergency stop function. One button is used to open and close the MOS tube.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eSleep mode (long press the stop button to view the current mode)\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eC-P sleep mode: within five minutes, without any operation, the digital tube automatically turns off the display, the program runs normally.\u003cbr data-mce-fragment=\"1\"\u003eO-d normal mode: the digital tube is always on display\u003cbr data-mce-fragment=\"1\"\u003ePress and hold the STOP button for 2 seconds and then release to switch the C-P and O-d states. The current state will flash and then return to the main interface.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eTiming range\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eHow to choose the timing range\u003cbr data-mce-fragment=\"1\"\u003e1).After setting the parameter value in the mode selection interface, press the STOP button to select the timing range.\u003cbr data-mce-fragment=\"1\"\u003eXXX. Decimal point is in one place, timing range: 1 second to 999 seconds\u003cbr data-mce-fragment=\"1\"\u003eXX.X decimal point in ten, timing range: 0.1 seconds to 99.9 seconds\u003cbr data-mce-fragment=\"1\"\u003eX.X.X. The decimal point is fully illuminated, the timing range is from 1 minute to 999 minutes.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e2).For example, if you want to set the OP to 3.2 seconds, move the decimal point to ten digits, and the digital tube displays 03.2.\u003cbr data-mce-fragment=\"1\"\u003eParameter description: OP on time, CL off time, LOP cycle number 1-999 times, \"---\" stands for infinite loop.\u003cbr data-mce-fragment=\"1\"\u003eThese parameters are independent of each other, but each mode shares these parameters. For example, when the on-time OP is set to 5 seconds in P1.1, the user wants to switch to the P1.2 mode, then when entering the P1.2 setting corresponding parameters, the OP also It will be 5 seconds.\u003cbr data-mce-fragment=\"1\"\u003eDisplaying 000 on the main interface and pressing the SET button will display OPL, LOP and corresponding time XXX\u003cbr data-mce-fragment=\"1\"\u003eIf only OP in the mode, such as mode P1.1, P1.2, P1.3 time, then short press SET button will only display OP and corresponding time.\u003cbr data-mce-fragment=\"1\"\u003eIf the mode has OP, CL, LOP such as mode P3.1, P3.2 short press SET button will display OP and corresponding time, CL and corresponding time, LOP and corresponding times.\u003cbr data-mce-fragment=\"1\"\u003eAfter setting the mode, it is very convenient to easily check the parameters set in the current mode by pressing the SET button on the main interface.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eHow to set parameters\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e1) First determine the working mode of the MOS tube\u003cbr data-mce-fragment=\"1\"\u003eAccording to the working mode of the MOS tube, in the main interface (when the module is powered on, it will flash the current working mode (default P1.1 mode), then enter the main interface \"press and hold the SET button for 2 seconds and then release\" to enter the mode. Select the interface, press the UP, DOWN button to select the mode to be set P1.1~P-4\u003cbr data-mce-fragment=\"1\"\u003e2) After selecting the mode to be set (for example, P3.2), press the SET button to set the corresponding parameter. At this time, the parameter to be set will flash OP ON time, CL OFF time, LOP cycle number “---” Represents an infinite loop, adjusts the parameter value through UP and DOWN, supports long press (rapid increase or decrease) and short press (increase or decrease 1 unit); after setting the parameter value, select the decimal point position by short pressing the STOP button. , select the timing range (corresponding time 0.1 seconds ~ 999 minutes); short press the SET button to set the next parameter of the current mode, the process is the same as above.\u003cbr data-mce-fragment=\"1\"\u003e3) After setting the parameters of the selected mode, press and hold the SET button for 2 seconds to release, the currently set mode will flash, then return to the main interface and set the parameters successfully.\u003cbr data-mce-fragment=\"1\"\u003e4) Main interface: “000” (no decimal point) is displayed when the MOS tube is not working, and the MOS tube has a decimal point in the working state.\u003cbr data-mce-fragment=\"1\"\u003e5) Mode selection interface: long press SET button to enter, after setting is completed, long press SET button to exit, return to the main interface\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cstrong data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eNote:\u003c\/span\u003e\u003c\/strong\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eThe module is an active live output, and the voltage at the output (load) is equal to the input voltage DC\u003c\/span\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e5.USD Digital Display Delay Controller: ( DC12V 4 Button )\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eDescription:\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003eThis relay delay control board has a powerful and clear interface, powerful function, one-button emergency stop function (STOP button), with reverse connection protection, reverse connection without burning, power-off memory. Increased sleep mode, after enabling, No operation within 5 minutes, automatically turn off the display, wake up any button! You can set different OP, CL, LOP parameters, these parameters are independent of each other, save the setting parameters automatically power-down save and other functions, almost meet all needs!\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eProduct manual:\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eWorking voltage: DC6V-DC30V (wide voltage anti-connection protection)\u003cbr data-mce-fragment=\"1\"\u003eTrigger signal source: high-level trigger DC 3.0V—24V signal ground and system ground to improve the system's anti-interference ability can also short-circuit the ground\u003cbr data-mce-fragment=\"1\"\u003eOutput capacity: controllable DC 30V\/10A or AC 250V\/10A equipment\u003cbr data-mce-fragment=\"1\"\u003eProduct size: 64mm*35mm*19.3mm\u003cbr data-mce-fragment=\"1\"\u003eMounting hole: diameter 3mm\u003cbr data-mce-fragment=\"1\"\u003eWorking temperature: -40 ° C ~ 85 ° C\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e6.DC Motor Speed Controller :(DC 8-55V Motor Speed Controller )\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eDescription:\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003eThis product brings together a wide range of modern motor speed control, with the advantages of small size, simple operation, high current resistance and reverse connection. Suitable for most users in various environments with various speeds, support acceleration and deceleration functions can be set through the menu, with set parameters power off permanent memory function\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eProduct manual:\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eVoltage: DC8V-55V (wide voltage anti-back protection)\u003cbr data-mce-fragment=\"1\"\u003eSpeed range: long press \/ short press to adjust the degree, 0% -100% speed\u003cbr data-mce-fragment=\"1\"\u003eDrive current: up to 10A, (recommended output series 12A fuse)\u003cbr data-mce-fragment=\"1\"\u003eStandby current: \u0026lt;17mA\u003cbr data-mce-fragment=\"1\"\u003eMounting hole: diameter 3mm\u003cbr data-mce-fragment=\"1\"\u003eProduct size: 64mm*35mm*19mm (length * width * height)\u003cbr data-mce-fragment=\"1\"\u003eWorking temperature: -20 ° C ~ 70 ° C\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eInstructions:\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e1. Click\/long press the “speed increase” button to increase the motor speed to 100%.\u003cbr data-mce-fragment=\"1\"\u003e2. Click\/long press the “speed down” button to increase the motor speed to a minimum of 0%.\u003cbr data-mce-fragment=\"1\"\u003e3. Press and hold the “Power On\/Off” button for one second, the controller will be turned on or off (the power is turned off by default, and the memory function is activated after booting)\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003ePrecautions:\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e1. The digital tube flashes at the moment of power-on (normal phenomenon, no need to worry)\u003cbr data-mce-fragment=\"1\"\u003e2, close to the limit drive current working conditions, it is recommended to take the output end of the fuse\u003cbr data-mce-fragment=\"1\"\u003e3. The DC motor speed controller cannot be installed in places where there is dripping water and children can reach it.\u003cbr data-mce-fragment=\"1\"\u003e4. After wiring, check if the line is correct and then energize, so as to avoid accidentally burning the temperature controller and load device.\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003eWiring:\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e“M+” and “M-” are respectively connected to the positive and negative terminals of the output, M+ is positive and M- is negative.\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e“VIN” and “GND” are respectively connected to the positive and negative terminals of the input terminal, Vin is positive and GND is negative (input power supply voltage is DC8V-55V)\u003c\/span\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e7.Temperature Controller:(DC 12V Temperrature Controller)\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eProduct Parameters:\u003c\/span\u003e\u003c\/strong\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003eControl range: -50~110°C\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eResolution: -9.9~99.9, 0.1°C, other temperature range, 1°C\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eTemperature measurement accuracy: 0.1 °C\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eControl accuracy: 0.1 ° C\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eHysteresis accuracy: 0.1 ° C\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eRefresh rate: 0.5S\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eHigh temperature alarm: 0-110 °C\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eMeasurement input: NTC (10K0.5%) waterproof sensor\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eOutput: One way 10A relay\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eEnvironmental requirements: Temperature -10~60°C Humidity 20%-85%\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eSize: 48*40mm\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003ePower consumption of the whole machine: quiescent current: ≤35MA, Pull-in current: ≤65MA\u003c\/span\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eSetting Parameter Method:\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eOnce the power supply and load are connected, the control can be powered. After power-on, the digital tube displays the current real-time temperature. Press the SET button briefly, the digital tube displays the temperature flashing, press the + - button to adjust the set temperature; after the adjustment is completed, press the SET button to save the set temperature and return. At this time, the controller automatically Execute the relay on and off; press and hold the SET button for 5 seconds to enter the menu parameter setting, short press the + - button to switch P0...P6, short press the SET button to enter the menu.\u003cbr data-mce-fragment=\"1\"\u003eThe thermostat output is a 10A relay to meet a variety of high power loads, please ensure that the line is correct.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eIndicator light, digital tube status description:\u003c\/strong\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003eIndicator light: Off means the relay is off, steady light means the relay is closed\u003cbr data-mce-fragment=\"1\"\u003eDigital tube: Display LLL for sensor open circuit: Display HHH is out of measurement range. The thermostat will forcibly open the relay.\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eParameter Function Description:\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003ctable data-mce-fragment=\"1\"\u003e\n\u003ctbody data-mce-fragment=\"1\"\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eMenu identifier\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eMenu function\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003ePredetermined area\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eFactory setting\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eP0\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eRefrigeration C \/ Heating H\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eC\/H\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eC\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eP1\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eBacklash\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e0.1-15\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e2.0\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eP2\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eMaximum set temperature\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e-50~110℃\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e110\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eP3\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eMinimum set temperature\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e-50~110℃\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e-50\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eP4\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eTemperature correction\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e-7.0~7.0℃\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e0.0\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eP5\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003ePress delay\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e0-10 minutes\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e0\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eP6\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eHigh temperature alarm\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003eON\/OFF\u003c\/td\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003eOFF\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003ePackage Included:\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e1PC*DC 12V 2\/3\/4 Button Time Delay Relay Motor Speed Temperrature Controller+Buzzer\u003cstrong data-mce-fragment=\"1\"\u003e(According to your choice)\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e"}