Capacitive Touch Dimmer Constant Pressure Stepless Dimming PWM Control Panel Type LED Dimmer Switch Diy Kit Electronic PCB Board

Capacitive Touch Dimmer Constant Pressure Stepless Dimming Pwm Control Panel Type Led Switch Diy Kit

Capacitive Touch Dimmer Constant Pressure Stepless Dimming PWM Control Panel Type LED Dimmer Switch Diy Kit Electronic PCB Board

SKU:011304
Regular price $3.99

 

 

 
 
PCB size:L23MM *W20MM        
Hole distance:16MM 
Aperture:2.5MM         
Voltage range:2.4-5V
Maximum output current:500MA
 
 
Features
 
1.The lamp brightness can be adjusted by requirement,it is very to operate.
2.It can touch in medium protection,such glass,acrylic,plastic,ceramics and so on,which is very safe.
3.Wide application of voltage range,you can choose arbitrarily between 2.4V to 4.5V.
4.Simple applied circuit,less peripheral devices, easy processing, low cost.
5.Anti power and phone interference,the EFT can reach above +/-2KV;the touch response sensitivity and reliability will not affected by the close distance or multi-angle mobile phone interference.
6.Install:Needn't to touch copper foil directly,the dimming can be processed across acrylic glass(above 3mm) or plastic.
7.Application:It can control LED module,light and so on.It is available for indoor LED,lighting lamp,DIY automotive lights dimming refit.
8.Function:Single touch,using the principle of capacitance touch .The default function is switch,dimming,with brightness memories LED touch dimming.It will light slowly when turn on the lights,and become dark slowly when turn off,which effectively avoid the stimulation to eyes.
9.Dimming mode:Non-polar PWM dimming.
10.Wiring method:PCB board(VCC,GND) is power input,(LED+, LED-) is connected with the LED lamps of positive and negative level (fingerprint) touch area, also can wire to lead out (the wiring should not be too long), copper skin area should be 2x3cm.With copper foil copper foil board module will side to the shell side.
11.Using method
a.Click touch(touch duration time is less than 550ms) can control the lamp.Click once, the lamp lights;click again,the lamp off.The initial brightness of lights lit the fixed for the whole brightness of 90%.
b.Press the touch at long time (touch duration time is more than 550ms), you can achieve stepless dimming the lights. Press long time once, light levels gradually increase light levels when released after the release time parked in the corresponding brightness, long time if more than three seconds, the light levels to achieve maximum brightness does not change; again long press touch, light levels gradually decreased to stop when you release the light levels in the corresponding brightness release time, if a long time more than three seconds, the light levels after reaching the minimum brightness does not change.
 
 
Note: 
        
the constant voltage dimmer output connect with LED, the upper limit must be coscade
 current-limiting resistance.   
Size for manual measurement, there may be a 0 to 2 cm error, belongs to the normal phenomenon. 
 
 
Package Included :
 
1  x  Capacitive Touch LED Dimmer PWM Control Switch Module
 
 

 







 
 
trust seal
  • guaranteeQuality checked
  • Special gift cardsSpecial gift cards
  • Free return Within 60 days
  • Consultancy86-0755-85201155

 

 

 
 
PCB size:L23MM *W20MM        
Hole distance:16MM 
Aperture:2.5MM         
Voltage range:2.4-5V
Maximum output current:500MA
 
 
Features
 
1.The lamp brightness can be adjusted by requirement,it is very to operate.
2.It can touch in medium protection,such glass,acrylic,plastic,ceramics and so on,which is very safe.
3.Wide application of voltage range,you can choose arbitrarily between 2.4V to 4.5V.
4.Simple applied circuit,less peripheral devices, easy processing, low cost.
5.Anti power and phone interference,the EFT can reach above +/-2KV;the touch response sensitivity and reliability will not affected by the close distance or multi-angle mobile phone interference.
6.Install:Needn't to touch copper foil directly,the dimming can be processed across acrylic glass(above 3mm) or plastic.
7.Application:It can control LED module,light and so on.It is available for indoor LED,lighting lamp,DIY automotive lights dimming refit.
8.Function:Single touch,using the principle of capacitance touch .The default function is switch,dimming,with brightness memories LED touch dimming.It will light slowly when turn on the lights,and become dark slowly when turn off,which effectively avoid the stimulation to eyes.
9.Dimming mode:Non-polar PWM dimming.
10.Wiring method:PCB board(VCC,GND) is power input,(LED+, LED-) is connected with the LED lamps of positive and negative level (fingerprint) touch area, also can wire to lead out (the wiring should not be too long), copper skin area should be 2x3cm.With copper foil copper foil board module will side to the shell side.
11.Using method
a.Click touch(touch duration time is less than 550ms) can control the lamp.Click once, the lamp lights;click again,the lamp off.The initial brightness of lights lit the fixed for the whole brightness of 90%.
b.Press the touch at long time (touch duration time is more than 550ms), you can achieve stepless dimming the lights. Press long time once, light levels gradually increase light levels when released after the release time parked in the corresponding brightness, long time if more than three seconds, the light levels to achieve maximum brightness does not change; again long press touch, light levels gradually decreased to stop when you release the light levels in the corresponding brightness release time, if a long time more than three seconds, the light levels after reaching the minimum brightness does not change.
 
 
Note: 
        
the constant voltage dimmer output connect with LED, the upper limit must be coscade
 current-limiting resistance.   
Size for manual measurement, there may be a 0 to 2 cm error, belongs to the normal phenomenon. 
 
 
Package Included :
 
1  x  Capacitive Touch LED Dimmer PWM Control Switch Module
 
 

 







 
 

Purchasing & Delivery

Before you make your purchase, it’s helpful to know the measurements of the area you plan to place the furniture. You should also measure any doorways and hallways through which the furniture will pass to get to its final destination.
Picking up at the store
Shopify Shop requires that all products are properly inspected BEFORE you take it home to insure there are no surprises. Our team is happy to open all packages and will assist in the inspection process. We will then reseal packages for safe transport. We encourage all customers to bring furniture pads or blankets to protect the items during transport as well as rope or tie downs. Shopify Shop will not be responsible for damage that occurs after leaving the store or during transit. It is the purchaser’s responsibility to make sure the correct items are picked up and in good condition.
Delivery
Customers are able to pick the next available delivery day that best fits their schedule. However, to route stops as efficiently as possible, Shopify Shop will provide the time frame. Customers will not be able to choose a time. You will be notified in advance of your scheduled time frame. Please make sure that a responsible adult (18 years or older) will be home at that time.
In preparation for your delivery, please remove existing furniture, pictures, mirrors, accessories, etc. to prevent damages. Also insure that the area where you would like your furniture placed is clear of any old furniture and any other items that may obstruct the passageway of the delivery team. Shopify Shop will deliver, assemble, and set-up your new furniture purchase and remove all packing materials from your home. Our delivery crews are not permitted to move your existing furniture or other household items. Delivery personnel will attempt to deliver the purchased items in a safe and controlled manner but will not attempt to place furniture if they feel it will result in damage to the product or your home. Delivery personnel are unable to remove doors, hoist furniture or carry furniture up more than 3 flights of stairs. An elevator must be available for deliveries to the 4th floor and above.