MH1220W 10A Digital Dual Display Temperature Controller Thermostat DC 12-72V/AC 110-220V

MH1220W 10A Digital Dual Display Temperature Controller Thermostat DC 12-72V/AC 110-220V

SKU:X13075
Regular price $10.59

shipped within one bussiness day

Power button instructions:
1 Press and hold the power button for 3 seconds to turn off, press and hold the power button for 3 seconds to turn it on again.
2 In the control temperature setting interface and mode setting interface, short press the power button to quickly save the settings and exit the setting interface.
Restore factory default: After pressing the △ and ▽ keys for 5 seconds at the same time, all the set parameters of the user will be restored to the factory defaults.
Parameter lock: Press and hold the ▽ button for 3 seconds and release the hand to display “0FF” to indicate that the user has set the parameter to be locked. In this way, the same operation flashes “ON” to indicate that the user has set the parameter lock to be released. (The user can only view and cannot modify after the parameter is locked, but the control degree adjustment is still valid)

Fault prompt:
When the sensor is short-circuited or when the ambient temperature is detected above the upper temperature limit of 120 degrees, the flashing indicates that the HHH well closes the output load. When the sensor is open or detects that the ambient temperature is below the lower temperature limit of -40 degrees, the LLL is flashed and the output load is turned off.

Precautions:
1. In order to prevent high-frequency interference, the sensing time line during installation cannot be bundled with the power line and the load device line, and separate wiring is required.
2. The power supply and the host marked voltage must be consistent, the rated voltage value deviation is not more than 1% 0%, the sensor is strictly distinguished from the sensor, power line and load output interface.
3. The thermostat main unit cannot be installed in places where dripping water, old people, and children are within easy reach.
4. After wiring, check whether the line is correct and then energize, so as to avoid accidentally burning the temperature controller and load equipment. After installation, apply the protective cover to cover.
Package Included:
1PCS* DC 12V-72V/ AC 110-220V MH1220W 10A Temperature Controller
trust seal
  • guaranteeQuality checked
  • Special gift cardsSpecial gift cards
  • Free return Within 60 days
  • Consultancy86-0755-85201155
Power button instructions:
1 Press and hold the power button for 3 seconds to turn off, press and hold the power button for 3 seconds to turn it on again.
2 In the control temperature setting interface and mode setting interface, short press the power button to quickly save the settings and exit the setting interface.
Restore factory default: After pressing the △ and ▽ keys for 5 seconds at the same time, all the set parameters of the user will be restored to the factory defaults.
Parameter lock: Press and hold the ▽ button for 3 seconds and release the hand to display “0FF” to indicate that the user has set the parameter to be locked. In this way, the same operation flashes “ON” to indicate that the user has set the parameter lock to be released. (The user can only view and cannot modify after the parameter is locked, but the control degree adjustment is still valid)

Fault prompt:
When the sensor is short-circuited or when the ambient temperature is detected above the upper temperature limit of 120 degrees, the flashing indicates that the HHH well closes the output load. When the sensor is open or detects that the ambient temperature is below the lower temperature limit of -40 degrees, the LLL is flashed and the output load is turned off.

Precautions:
1. In order to prevent high-frequency interference, the sensing time line during installation cannot be bundled with the power line and the load device line, and separate wiring is required.
2. The power supply and the host marked voltage must be consistent, the rated voltage value deviation is not more than 1% 0%, the sensor is strictly distinguished from the sensor, power line and load output interface.
3. The thermostat main unit cannot be installed in places where dripping water, old people, and children are within easy reach.
4. After wiring, check whether the line is correct and then energize, so as to avoid accidentally burning the temperature controller and load equipment. After installation, apply the protective cover to cover.
Package Included:
1PCS* DC 12V-72V/ AC 110-220V MH1220W 10A Temperature Controller

Purchasing & Delivery

Before you make your purchase, it’s helpful to know the measurements of the area you plan to place the furniture. You should also measure any doorways and hallways through which the furniture will pass to get to its final destination.
Picking up at the store
Shopify Shop requires that all products are properly inspected BEFORE you take it home to insure there are no surprises. Our team is happy to open all packages and will assist in the inspection process. We will then reseal packages for safe transport. We encourage all customers to bring furniture pads or blankets to protect the items during transport as well as rope or tie downs. Shopify Shop will not be responsible for damage that occurs after leaving the store or during transit. It is the purchaser’s responsibility to make sure the correct items are picked up and in good condition.
Delivery
Customers are able to pick the next available delivery day that best fits their schedule. However, to route stops as efficiently as possible, Shopify Shop will provide the time frame. Customers will not be able to choose a time. You will be notified in advance of your scheduled time frame. Please make sure that a responsible adult (18 years or older) will be home at that time.
In preparation for your delivery, please remove existing furniture, pictures, mirrors, accessories, etc. to prevent damages. Also insure that the area where you would like your furniture placed is clear of any old furniture and any other items that may obstruct the passageway of the delivery team. Shopify Shop will deliver, assemble, and set-up your new furniture purchase and remove all packing materials from your home. Our delivery crews are not permitted to move your existing furniture or other household items. Delivery personnel will attempt to deliver the purchased items in a safe and controlled manner but will not attempt to place furniture if they feel it will result in damage to the product or your home. Delivery personnel are unable to remove doors, hoist furniture or carry furniture up more than 3 flights of stairs. An elevator must be available for deliveries to the 4th floor and above.