SN65HVD230 CAN Bus Transceiver Communication Module Thermal Protection Slope Control Logic for Arduino Controller Board

Sn65Hvd230 Can Bus Transceiver Communication Module Thermal Protection Slope Control Logic For

SN65HVD230 CAN Bus Transceiver Communication Module Thermal Protection Slope Control Logic for Arduino Controller Board

SKU:010672
Regular price $4.99

 

 

SN65HVD230 CAN Bus Transceiver Communication Module Thermal Protection Slope Control for Arduino

Product Description

SN65HVD230 can be used under high interference environment.
The device has the ability to send and receive good at different rates,
and its main features are as follows:

Fully compatible with ISO11898 standard;
High input impedance, allowing 120 nodes;
Low current standby mode, the typical current of 370μA;
Signal transfer rate up to 1Mb / s;
Thermal protection, open circuit failure protection function;
With anti-instantaneous interference protection bus;
Slope control, reduce radio frequency interference (RFI);
Differential receiver with a wide range of anti-common-mode interference,
electromagnetic interference (EMI) capabilities.
 
Operating modes and control logic
 
SN65HVD230 high speed, slope and wait three different modes of operation.
Its working mode control can be achieved by the control pin Rs.
Figure 2 is a SN65HVD230 CAN bus system in a typical application diagram.
Can be seen from the figure, CAN controller is connected
to the output pin Tx SN65HVD230 data input terminal D,
this data can be transferred to the CAN node sends CAN network;
CAN controller and receive pins of Rx and SN65HVD230 R is connected to
the data output terminal, for receiving data.
Select the port Rs SN65HVD230 way via jumpers and end of
the ground slope resistor can be achieved through hardware
mode select three modes of operation, in which
the slope is 0 ~ 100kΩ resistor potentiometer

Package Included:

1 x  SN65HVD230 CAN bus transceiver communication module For for arduino

 

 

 

 

 

trust seal
  • guaranteeQuality checked
  • Special gift cardsSpecial gift cards
  • Free return Within 60 days
  • Consultancy86-0755-85201155

 

 

SN65HVD230 CAN Bus Transceiver Communication Module Thermal Protection Slope Control for Arduino

Product Description

SN65HVD230 can be used under high interference environment.
The device has the ability to send and receive good at different rates,
and its main features are as follows:

Fully compatible with ISO11898 standard;
High input impedance, allowing 120 nodes;
Low current standby mode, the typical current of 370μA;
Signal transfer rate up to 1Mb / s;
Thermal protection, open circuit failure protection function;
With anti-instantaneous interference protection bus;
Slope control, reduce radio frequency interference (RFI);
Differential receiver with a wide range of anti-common-mode interference,
electromagnetic interference (EMI) capabilities.
 
Operating modes and control logic
 
SN65HVD230 high speed, slope and wait three different modes of operation.
Its working mode control can be achieved by the control pin Rs.
Figure 2 is a SN65HVD230 CAN bus system in a typical application diagram.
Can be seen from the figure, CAN controller is connected
to the output pin Tx SN65HVD230 data input terminal D,
this data can be transferred to the CAN node sends CAN network;
CAN controller and receive pins of Rx and SN65HVD230 R is connected to
the data output terminal, for receiving data.
Select the port Rs SN65HVD230 way via jumpers and end of
the ground slope resistor can be achieved through hardware
mode select three modes of operation, in which
the slope is 0 ~ 100kΩ resistor potentiometer

Package Included:

1 x  SN65HVD230 CAN bus transceiver communication module For for arduino

 

 

 

 

 

Purchasing & Delivery

Before you make your purchase, it’s helpful to know the measurements of the area you plan to place the furniture. You should also measure any doorways and hallways through which the furniture will pass to get to its final destination.
Picking up at the store
Shopify Shop requires that all products are properly inspected BEFORE you take it home to insure there are no surprises. Our team is happy to open all packages and will assist in the inspection process. We will then reseal packages for safe transport. We encourage all customers to bring furniture pads or blankets to protect the items during transport as well as rope or tie downs. Shopify Shop will not be responsible for damage that occurs after leaving the store or during transit. It is the purchaser’s responsibility to make sure the correct items are picked up and in good condition.
Delivery
Customers are able to pick the next available delivery day that best fits their schedule. However, to route stops as efficiently as possible, Shopify Shop will provide the time frame. Customers will not be able to choose a time. You will be notified in advance of your scheduled time frame. Please make sure that a responsible adult (18 years or older) will be home at that time.
In preparation for your delivery, please remove existing furniture, pictures, mirrors, accessories, etc. to prevent damages. Also insure that the area where you would like your furniture placed is clear of any old furniture and any other items that may obstruct the passageway of the delivery team. Shopify Shop will deliver, assemble, and set-up your new furniture purchase and remove all packing materials from your home. Our delivery crews are not permitted to move your existing furniture or other household items. Delivery personnel will attempt to deliver the purchased items in a safe and controlled manner but will not attempt to place furniture if they feel it will result in damage to the product or your home. Delivery personnel are unable to remove doors, hoist furniture or carry furniture up more than 3 flights of stairs. An elevator must be available for deliveries to the 4th floor and above.