AC 260V 100A Digital LCD Panel Volt AMP Meter Power Energy Ammeter Vol

AC 260V 100A Digital LCD Panel Volt AMP Meter Power Energy Ammeter Voltmeter

SKU:011748

$13.99

Description
A Function

Electrical parameter measurement function (voltage, current, active power, energy)
Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).
Power alarm threshold preset function (can set power alarm threshold).
Reset energy function.
Store data when power off.
STN whole viewing angleLCD (display voltage, current, active power/energy at the same time)
Backlight function.

B. Appearance and Key function

Display Interface
The large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)

II.Display format

Power: test range: 0~22kW
within 1KW, the display format is 0.0~999.9W;
1KW and above, the display format is 1000~9999W;
10kw and above, the display format is 10.0~22.0kW
Energy: test range: 0~9999kWh
Within 10KWh, the display format is 0~9999Wh;
10kWh and above, the display format is 10~9999kWh;
Over 9999kwh will return 0
Voltage: test range: 80~260V
Display format: 80~260V
Current: test range: 0~100A
Display format: 0.00~99.99A

III. Key

Backlight control
Short press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.

Reset energy

Step1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.
Step2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.
Set power alarm threshold
Step1: Long press the key at least 3 seconds until the number in power display area flash,then release the key
Step2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)
Step3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.
Power/Energy switch
You can short press the key to switch display the power/ energy, the display state will be store when power off.

Precautions

This module is suitable for indoor, please do not use outdoor.
Applied load should not exceed the rated power.
Wiring order can’t be wrong.
Specification parameters
Working voltage: 80 ~ 260VAC
Test voltage: 80 ~ 260VAC
Rated power: 22kW
Operating frequency: 45-65Hz
Measurement accuracy: 1.0 grade

Package Included:

1PC*100A AC 260V Digital LCD Panel Voltage Meter Power Energy Ammeter Voltmeter

Quantity

guaranteeQuality checked
Special gift cardsSpecial gift cards
Free return Within 60 days
Consultancy86-0755-85201155

Description
A Function

Electrical parameter measurement function (voltage, current, active power, energy)
Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).
Power alarm threshold preset function (can set power alarm threshold).
Reset energy function.
Store data when power off.
STN whole viewing angleLCD (display voltage, current, active power/energy at the same time)
Backlight function.

B. Appearance and Key function

Display Interface
The large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)

II.Display format

Power: test range: 0~22kW
within 1KW, the display format is 0.0~999.9W;
1KW and above, the display format is 1000~9999W;
10kw and above, the display format is 10.0~22.0kW
Energy: test range: 0~9999kWh
Within 10KWh, the display format is 0~9999Wh;
10kWh and above, the display format is 10~9999kWh;
Over 9999kwh will return 0
Voltage: test range: 80~260V
Display format: 80~260V
Current: test range: 0~100A
Display format: 0.00~99.99A

III. Key

Backlight control
Short press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.

Reset energy

Step1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.
Step2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.
Set power alarm threshold
Step1: Long press the key at least 3 seconds until the number in power display area flash,then release the key
Step2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)
Step3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.
Power/Energy switch
You can short press the key to switch display the power/ energy, the display state will be store when power off.

Precautions

This module is suitable for indoor, please do not use outdoor.
Applied load should not exceed the rated power.
Wiring order can’t be wrong.
Specification parameters
Working voltage: 80 ~ 260VAC
Test voltage: 80 ~ 260VAC
Rated power: 22kW
Operating frequency: 45-65Hz
Measurement accuracy: 1.0 grade

Package Included:

1PC*100A AC 260V Digital LCD Panel Voltage Meter Power Energy Ammeter Voltmeter

Manual

Purchasing & Delivery

Before you make your purchase, it’s helpful to know the measurements of the area you plan to place the furniture. You should also measure any doorways and hallways through which the furniture will pass to get to its final destination.

Picking up at the store

Shopify Shop requires that all products are properly inspected BEFORE you take it home to insure there are no surprises. Our team is happy to open all packages and will assist in the inspection process. We will then reseal packages for safe transport. We encourage all customers to bring furniture pads or blankets to protect the items during transport as well as rope or tie downs. Shopify Shop will not be responsible for damage that occurs after leaving the store or during transit. It is the purchaser’s responsibility to make sure the correct items are picked up and in good condition.

Delivery

Customers are able to pick the next available delivery day that best fits their schedule. However, to route stops as efficiently as possible, Shopify Shop will provide the time frame. Customers will not be able to choose a time. You will be notified in advance of your scheduled time frame. Please make sure that a responsible adult (18 years or older) will be home at that time.
In preparation for your delivery, please remove existing furniture, pictures, mirrors, accessories, etc. to prevent damages. Also insure that the area where you would like your furniture placed is clear of any old furniture and any other items that may obstruct the passageway of the delivery team. Shopify Shop will deliver, assemble, and set-up your new furniture purchase and remove all packing materials from your home. Our delivery crews are not permitted to move your existing furniture or other household items. Delivery personnel will attempt to deliver the purchased items in a safe and controlled manner but will not attempt to place furniture if they feel it will result in damage to the product or your home. Delivery personnel are unable to remove doors, hoist furniture or carry furniture up more than 3 flights of stairs. An elevator must be available for deliveries to the 4th floor and above.

Other Customers also buy:

USB Charger Doctor Capacity Tester LCD Display Current Voltage Detector Meter

Translation missing: en.products.product.regular_price $7.99
{"id":4795785936967,"title":"AC 260V 100A Digital LCD Panel Volt AMP Meter Power Energy Ammeter Voltmeter","handle":"ac-260v-100a-digital-lcd-panel-volt-amp-meter-power-energy-ammeter-voltmeter","description":"\u003cspan lang=\"en\"\u003e\u003cspan lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e\u003cstrong\u003eDescription\u003c\/strong\u003e\u003cbr\u003e\u003cstrong\u003eA Function\u003c\/strong\u003e\u003cbr\u003e\u003c\/span\u003e\u003c\/span\u003e\u003c\/span\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eElectrical parameter measurement function (voltage, current, active power, energy)\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eOverload alarm function (over power alarm threshold, backlight and power flashing to alarm).\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003ePower alarm threshold preset function (can set power alarm threshold).\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eReset energy function.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eStore data when power off.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eSTN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e Backlight function.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cspan lang=\"en\"\u003e\u003cspan lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e\u003cstrong\u003eB. Appearance and Key function\u003c\/strong\u003e\u003cbr\u003e\u003c\/span\u003e\u003c\/span\u003e\u003c\/span\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eDisplay Interface\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cspan lang=\"en\"\u003e\u003cspan lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e\u003cstrong\u003eII.Display format\u003c\/strong\u003e\u003cbr\u003e\u003c\/span\u003e\u003c\/span\u003e\u003c\/span\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003ePower: test range: 0~22kW\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003ewithin 1KW, the display format is 0.0~999.9W;\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e1KW and above, the display format is 1000~9999W;\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e10kw and above, the display format is 10.0~22.0kW\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eEnergy: test range: 0~9999kWh\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eWithin 10KWh, the display format is 0~9999Wh;\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e10kWh and above, the display format is 10~9999kWh;\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eOver 9999kwh will return 0\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eVoltage: test range: 80~260V\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eDisplay format: 80~260V\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eCurrent: test range: 0~100A\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eDisplay format: 0.00~99.99A\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cspan lang=\"en\"\u003e\u003cspan lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e\u003cstrong\u003eIII. Key\u003c\/strong\u003e\u003cbr\u003e\u003c\/span\u003e\u003c\/span\u003e\u003c\/span\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eBacklight control\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cspan lang=\"en\"\u003e\u003cspan lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e\u003cstrong\u003eReset energy\u003c\/strong\u003e\u003cbr\u003e\u003c\/span\u003e\u003c\/span\u003e\u003c\/span\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eSet power alarm threshold\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003ePower\/Energy switch\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cspan lang=\"en\"\u003e\u003cspan lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e\u003cstrong\u003ePrecautions\u003c\/strong\u003e\u003cbr\u003e\u003c\/span\u003e\u003c\/span\u003e\u003c\/span\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eThis module is suitable for indoor, please do not use outdoor.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eApplied load should not exceed the rated power.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eWiring order can’t be wrong.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eSpecification parameters\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eWorking voltage: 80 ~ 260VAC\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eTest voltage: 80 ~ 260VAC\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eRated power: 22kW\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eOperating frequency: 45-65Hz\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eMeasurement accuracy: 1.0 grade \u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cspan lang=\"en\"\u003e\u003cspan lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e\u003cstrong\u003ePackage Included:\u003c\/strong\u003e\u003cbr\u003e\u003c\/span\u003e\u003c\/span\u003e\u003c\/span\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e1PC*100A AC 260V Digital LCD Panel Voltage Meter Power Energy Ammeter Voltmeter\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e","published_at":"2020-08-17T11:41:23+08:00","created_at":"2020-08-17T11:41:21+08:00","vendor":"DIYMORE","type":"","tags":[],"price":1399,"price_min":1399,"price_max":1399,"available":true,"price_varies":false,"compare_at_price":null,"compare_at_price_min":0,"compare_at_price_max":0,"compare_at_price_varies":false,"variants":[{"id":32513430552647,"title":"Default Title","option1":"Default Title","option2":null,"option3":null,"sku":"011748","requires_shipping":true,"taxable":false,"featured_image":null,"available":true,"name":"AC 260V 100A Digital LCD Panel Volt AMP Meter Power Energy Ammeter Voltmeter","public_title":null,"options":["Default Title"],"price":1399,"weight":100,"compare_at_price":null,"inventory_management":"shopify","barcode":"","requires_selling_plan":false,"selling_plan_allocations":[]}],"images":["\/\/www.diymore.cc\/cdn\/shop\/products\/011748_1.jpg?v=1597635684","\/\/www.diymore.cc\/cdn\/shop\/products\/011748_2.jpg?v=1597635684","\/\/www.diymore.cc\/cdn\/shop\/products\/011748_3.jpg?v=1597635684","\/\/www.diymore.cc\/cdn\/shop\/products\/011748_4.jpg?v=1597635684","\/\/www.diymore.cc\/cdn\/shop\/products\/011748_5.jpg?v=1597635684","\/\/www.diymore.cc\/cdn\/shop\/products\/011748_8.jpg?v=1597635684"],"featured_image":"\/\/www.diymore.cc\/cdn\/shop\/products\/011748_1.jpg?v=1597635684","options":["Title"],"media":[{"alt":null,"id":7291926872135,"position":1,"preview_image":{"aspect_ratio":1.25,"height":800,"width":1000,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011748_1.jpg?v=1597635684"},"aspect_ratio":1.25,"height":800,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011748_1.jpg?v=1597635684","width":1000},{"alt":null,"id":7291926904903,"position":2,"preview_image":{"aspect_ratio":1.253,"height":700,"width":877,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011748_2.jpg?v=1597635684"},"aspect_ratio":1.253,"height":700,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011748_2.jpg?v=1597635684","width":877},{"alt":null,"id":7291926937671,"position":3,"preview_image":{"aspect_ratio":1.238,"height":800,"width":990,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011748_3.jpg?v=1597635684"},"aspect_ratio":1.238,"height":800,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011748_3.jpg?v=1597635684","width":990},{"alt":null,"id":7291926970439,"position":4,"preview_image":{"aspect_ratio":1.255,"height":600,"width":753,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011748_4.jpg?v=1597635684"},"aspect_ratio":1.255,"height":600,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011748_4.jpg?v=1597635684","width":753},{"alt":null,"id":7291927003207,"position":5,"preview_image":{"aspect_ratio":1.252,"height":600,"width":751,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011748_5.jpg?v=1597635684"},"aspect_ratio":1.252,"height":600,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011748_5.jpg?v=1597635684","width":751},{"alt":null,"id":7291927035975,"position":6,"preview_image":{"aspect_ratio":1.154,"height":800,"width":923,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011748_8.jpg?v=1597635684"},"aspect_ratio":1.154,"height":800,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011748_8.jpg?v=1597635684","width":923}],"requires_selling_plan":false,"selling_plan_groups":[],"content":"\u003cspan lang=\"en\"\u003e\u003cspan lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e\u003cstrong\u003eDescription\u003c\/strong\u003e\u003cbr\u003e\u003cstrong\u003eA Function\u003c\/strong\u003e\u003cbr\u003e\u003c\/span\u003e\u003c\/span\u003e\u003c\/span\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eElectrical parameter measurement function (voltage, current, active power, energy)\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eOverload alarm function (over power alarm threshold, backlight and power flashing to alarm).\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003ePower alarm threshold preset function (can set power alarm threshold).\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eReset energy function.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eStore data when power off.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eSTN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e Backlight function.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cspan lang=\"en\"\u003e\u003cspan lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e\u003cstrong\u003eB. Appearance and Key function\u003c\/strong\u003e\u003cbr\u003e\u003c\/span\u003e\u003c\/span\u003e\u003c\/span\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eDisplay Interface\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cspan lang=\"en\"\u003e\u003cspan lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e\u003cstrong\u003eII.Display format\u003c\/strong\u003e\u003cbr\u003e\u003c\/span\u003e\u003c\/span\u003e\u003c\/span\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003ePower: test range: 0~22kW\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003ewithin 1KW, the display format is 0.0~999.9W;\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e1KW and above, the display format is 1000~9999W;\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e10kw and above, the display format is 10.0~22.0kW\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eEnergy: test range: 0~9999kWh\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eWithin 10KWh, the display format is 0~9999Wh;\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e10kWh and above, the display format is 10~9999kWh;\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eOver 9999kwh will return 0\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eVoltage: test range: 80~260V\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eDisplay format: 80~260V\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eCurrent: test range: 0~100A\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eDisplay format: 0.00~99.99A\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cspan lang=\"en\"\u003e\u003cspan lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e\u003cstrong\u003eIII. Key\u003c\/strong\u003e\u003cbr\u003e\u003c\/span\u003e\u003c\/span\u003e\u003c\/span\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eBacklight control\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cspan lang=\"en\"\u003e\u003cspan lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e\u003cstrong\u003eReset energy\u003c\/strong\u003e\u003cbr\u003e\u003c\/span\u003e\u003c\/span\u003e\u003c\/span\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eSet power alarm threshold\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003ePower\/Energy switch\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cspan lang=\"en\"\u003e\u003cspan lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e\u003cstrong\u003ePrecautions\u003c\/strong\u003e\u003cbr\u003e\u003c\/span\u003e\u003c\/span\u003e\u003c\/span\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eThis module is suitable for indoor, please do not use outdoor.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eApplied load should not exceed the rated power.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eWiring order can’t be wrong.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eSpecification parameters\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eWorking voltage: 80 ~ 260VAC\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eTest voltage: 80 ~ 260VAC\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eRated power: 22kW\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eOperating frequency: 45-65Hz\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eMeasurement accuracy: 1.0 grade \u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cspan lang=\"en\"\u003e\u003cspan lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e\u003cstrong\u003ePackage Included:\u003c\/strong\u003e\u003cbr\u003e\u003c\/span\u003e\u003c\/span\u003e\u003c\/span\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e1PC*100A AC 260V Digital LCD Panel Voltage Meter Power Energy Ammeter Voltmeter\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e"}
Digital DC 50V 5A 250W / 100V 10A 1000W LCD Voltmeter Ammeter Power Meter

Translation missing: en.products.product.regular_price $7.99
{"id":4795785936967,"title":"AC 260V 100A Digital LCD Panel Volt AMP Meter Power Energy Ammeter Voltmeter","handle":"ac-260v-100a-digital-lcd-panel-volt-amp-meter-power-energy-ammeter-voltmeter","description":"\u003cspan lang=\"en\"\u003e\u003cspan lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e\u003cstrong\u003eDescription\u003c\/strong\u003e\u003cbr\u003e\u003cstrong\u003eA Function\u003c\/strong\u003e\u003cbr\u003e\u003c\/span\u003e\u003c\/span\u003e\u003c\/span\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eElectrical parameter measurement function (voltage, current, active power, energy)\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eOverload alarm function (over power alarm threshold, backlight and power flashing to alarm).\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003ePower alarm threshold preset function (can set power alarm threshold).\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eReset energy function.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eStore data when power off.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eSTN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e Backlight function.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cspan lang=\"en\"\u003e\u003cspan lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e\u003cstrong\u003eB. Appearance and Key function\u003c\/strong\u003e\u003cbr\u003e\u003c\/span\u003e\u003c\/span\u003e\u003c\/span\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eDisplay Interface\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cspan lang=\"en\"\u003e\u003cspan lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e\u003cstrong\u003eII.Display format\u003c\/strong\u003e\u003cbr\u003e\u003c\/span\u003e\u003c\/span\u003e\u003c\/span\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003ePower: test range: 0~22kW\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003ewithin 1KW, the display format is 0.0~999.9W;\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e1KW and above, the display format is 1000~9999W;\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e10kw and above, the display format is 10.0~22.0kW\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eEnergy: test range: 0~9999kWh\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eWithin 10KWh, the display format is 0~9999Wh;\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e10kWh and above, the display format is 10~9999kWh;\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eOver 9999kwh will return 0\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eVoltage: test range: 80~260V\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eDisplay format: 80~260V\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eCurrent: test range: 0~100A\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eDisplay format: 0.00~99.99A\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cspan lang=\"en\"\u003e\u003cspan lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e\u003cstrong\u003eIII. Key\u003c\/strong\u003e\u003cbr\u003e\u003c\/span\u003e\u003c\/span\u003e\u003c\/span\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eBacklight control\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cspan lang=\"en\"\u003e\u003cspan lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e\u003cstrong\u003eReset energy\u003c\/strong\u003e\u003cbr\u003e\u003c\/span\u003e\u003c\/span\u003e\u003c\/span\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eSet power alarm threshold\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003ePower\/Energy switch\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cspan lang=\"en\"\u003e\u003cspan lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e\u003cstrong\u003ePrecautions\u003c\/strong\u003e\u003cbr\u003e\u003c\/span\u003e\u003c\/span\u003e\u003c\/span\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eThis module is suitable for indoor, please do not use outdoor.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eApplied load should not exceed the rated power.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eWiring order can’t be wrong.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eSpecification parameters\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eWorking voltage: 80 ~ 260VAC\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eTest voltage: 80 ~ 260VAC\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eRated power: 22kW\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eOperating frequency: 45-65Hz\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eMeasurement accuracy: 1.0 grade \u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cspan lang=\"en\"\u003e\u003cspan lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e\u003cstrong\u003ePackage Included:\u003c\/strong\u003e\u003cbr\u003e\u003c\/span\u003e\u003c\/span\u003e\u003c\/span\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e1PC*100A AC 260V Digital LCD Panel Voltage Meter Power Energy Ammeter Voltmeter\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e","published_at":"2020-08-17T11:41:23+08:00","created_at":"2020-08-17T11:41:21+08:00","vendor":"DIYMORE","type":"","tags":[],"price":1399,"price_min":1399,"price_max":1399,"available":true,"price_varies":false,"compare_at_price":null,"compare_at_price_min":0,"compare_at_price_max":0,"compare_at_price_varies":false,"variants":[{"id":32513430552647,"title":"Default Title","option1":"Default Title","option2":null,"option3":null,"sku":"011748","requires_shipping":true,"taxable":false,"featured_image":null,"available":true,"name":"AC 260V 100A Digital LCD Panel Volt AMP Meter Power Energy Ammeter Voltmeter","public_title":null,"options":["Default Title"],"price":1399,"weight":100,"compare_at_price":null,"inventory_management":"shopify","barcode":"","requires_selling_plan":false,"selling_plan_allocations":[]}],"images":["\/\/www.diymore.cc\/cdn\/shop\/products\/011748_1.jpg?v=1597635684","\/\/www.diymore.cc\/cdn\/shop\/products\/011748_2.jpg?v=1597635684","\/\/www.diymore.cc\/cdn\/shop\/products\/011748_3.jpg?v=1597635684","\/\/www.diymore.cc\/cdn\/shop\/products\/011748_4.jpg?v=1597635684","\/\/www.diymore.cc\/cdn\/shop\/products\/011748_5.jpg?v=1597635684","\/\/www.diymore.cc\/cdn\/shop\/products\/011748_8.jpg?v=1597635684"],"featured_image":"\/\/www.diymore.cc\/cdn\/shop\/products\/011748_1.jpg?v=1597635684","options":["Title"],"media":[{"alt":null,"id":7291926872135,"position":1,"preview_image":{"aspect_ratio":1.25,"height":800,"width":1000,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011748_1.jpg?v=1597635684"},"aspect_ratio":1.25,"height":800,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011748_1.jpg?v=1597635684","width":1000},{"alt":null,"id":7291926904903,"position":2,"preview_image":{"aspect_ratio":1.253,"height":700,"width":877,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011748_2.jpg?v=1597635684"},"aspect_ratio":1.253,"height":700,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011748_2.jpg?v=1597635684","width":877},{"alt":null,"id":7291926937671,"position":3,"preview_image":{"aspect_ratio":1.238,"height":800,"width":990,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011748_3.jpg?v=1597635684"},"aspect_ratio":1.238,"height":800,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011748_3.jpg?v=1597635684","width":990},{"alt":null,"id":7291926970439,"position":4,"preview_image":{"aspect_ratio":1.255,"height":600,"width":753,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011748_4.jpg?v=1597635684"},"aspect_ratio":1.255,"height":600,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011748_4.jpg?v=1597635684","width":753},{"alt":null,"id":7291927003207,"position":5,"preview_image":{"aspect_ratio":1.252,"height":600,"width":751,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011748_5.jpg?v=1597635684"},"aspect_ratio":1.252,"height":600,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011748_5.jpg?v=1597635684","width":751},{"alt":null,"id":7291927035975,"position":6,"preview_image":{"aspect_ratio":1.154,"height":800,"width":923,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011748_8.jpg?v=1597635684"},"aspect_ratio":1.154,"height":800,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011748_8.jpg?v=1597635684","width":923}],"requires_selling_plan":false,"selling_plan_groups":[],"content":"\u003cspan lang=\"en\"\u003e\u003cspan lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e\u003cstrong\u003eDescription\u003c\/strong\u003e\u003cbr\u003e\u003cstrong\u003eA Function\u003c\/strong\u003e\u003cbr\u003e\u003c\/span\u003e\u003c\/span\u003e\u003c\/span\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eElectrical parameter measurement function (voltage, current, active power, energy)\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eOverload alarm function (over power alarm threshold, backlight and power flashing to alarm).\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003ePower alarm threshold preset function (can set power alarm threshold).\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eReset energy function.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eStore data when power off.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eSTN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e Backlight function.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cspan lang=\"en\"\u003e\u003cspan lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e\u003cstrong\u003eB. Appearance and Key function\u003c\/strong\u003e\u003cbr\u003e\u003c\/span\u003e\u003c\/span\u003e\u003c\/span\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eDisplay Interface\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cspan lang=\"en\"\u003e\u003cspan lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e\u003cstrong\u003eII.Display format\u003c\/strong\u003e\u003cbr\u003e\u003c\/span\u003e\u003c\/span\u003e\u003c\/span\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003ePower: test range: 0~22kW\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003ewithin 1KW, the display format is 0.0~999.9W;\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e1KW and above, the display format is 1000~9999W;\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e10kw and above, the display format is 10.0~22.0kW\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eEnergy: test range: 0~9999kWh\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eWithin 10KWh, the display format is 0~9999Wh;\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e10kWh and above, the display format is 10~9999kWh;\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eOver 9999kwh will return 0\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eVoltage: test range: 80~260V\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eDisplay format: 80~260V\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eCurrent: test range: 0~100A\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eDisplay format: 0.00~99.99A\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cspan lang=\"en\"\u003e\u003cspan lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e\u003cstrong\u003eIII. Key\u003c\/strong\u003e\u003cbr\u003e\u003c\/span\u003e\u003c\/span\u003e\u003c\/span\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eBacklight control\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cspan lang=\"en\"\u003e\u003cspan lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e\u003cstrong\u003eReset energy\u003c\/strong\u003e\u003cbr\u003e\u003c\/span\u003e\u003c\/span\u003e\u003c\/span\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eSet power alarm threshold\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003ePower\/Energy switch\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cspan lang=\"en\"\u003e\u003cspan lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e\u003cstrong\u003ePrecautions\u003c\/strong\u003e\u003cbr\u003e\u003c\/span\u003e\u003c\/span\u003e\u003c\/span\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eThis module is suitable for indoor, please do not use outdoor.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eApplied load should not exceed the rated power.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eWiring order can’t be wrong.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eSpecification parameters\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eWorking voltage: 80 ~ 260VAC\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eTest voltage: 80 ~ 260VAC\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eRated power: 22kW\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eOperating frequency: 45-65Hz\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eMeasurement accuracy: 1.0 grade \u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cspan lang=\"en\"\u003e\u003cspan lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e\u003cstrong\u003ePackage Included:\u003c\/strong\u003e\u003cbr\u003e\u003c\/span\u003e\u003c\/span\u003e\u003c\/span\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e1PC*100A AC 260V Digital LCD Panel Voltage Meter Power Energy Ammeter Voltmeter\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e"}
1.3" Blue OLED LCD 4Pin Display Module IIC I2C 128x64 3-5V Interface for Arduino

Translation missing: en.products.product.regular_price $10.99
{"id":4795785936967,"title":"AC 260V 100A Digital LCD Panel Volt AMP Meter Power Energy Ammeter Voltmeter","handle":"ac-260v-100a-digital-lcd-panel-volt-amp-meter-power-energy-ammeter-voltmeter","description":"\u003cspan lang=\"en\"\u003e\u003cspan lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e\u003cstrong\u003eDescription\u003c\/strong\u003e\u003cbr\u003e\u003cstrong\u003eA Function\u003c\/strong\u003e\u003cbr\u003e\u003c\/span\u003e\u003c\/span\u003e\u003c\/span\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eElectrical parameter measurement function (voltage, current, active power, energy)\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eOverload alarm function (over power alarm threshold, backlight and power flashing to alarm).\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003ePower alarm threshold preset function (can set power alarm threshold).\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eReset energy function.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eStore data when power off.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eSTN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e Backlight function.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cspan lang=\"en\"\u003e\u003cspan lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e\u003cstrong\u003eB. Appearance and Key function\u003c\/strong\u003e\u003cbr\u003e\u003c\/span\u003e\u003c\/span\u003e\u003c\/span\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eDisplay Interface\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cspan lang=\"en\"\u003e\u003cspan lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e\u003cstrong\u003eII.Display format\u003c\/strong\u003e\u003cbr\u003e\u003c\/span\u003e\u003c\/span\u003e\u003c\/span\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003ePower: test range: 0~22kW\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003ewithin 1KW, the display format is 0.0~999.9W;\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e1KW and above, the display format is 1000~9999W;\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e10kw and above, the display format is 10.0~22.0kW\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eEnergy: test range: 0~9999kWh\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eWithin 10KWh, the display format is 0~9999Wh;\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e10kWh and above, the display format is 10~9999kWh;\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eOver 9999kwh will return 0\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eVoltage: test range: 80~260V\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eDisplay format: 80~260V\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eCurrent: test range: 0~100A\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eDisplay format: 0.00~99.99A\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cspan lang=\"en\"\u003e\u003cspan lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e\u003cstrong\u003eIII. Key\u003c\/strong\u003e\u003cbr\u003e\u003c\/span\u003e\u003c\/span\u003e\u003c\/span\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eBacklight control\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cspan lang=\"en\"\u003e\u003cspan lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e\u003cstrong\u003eReset energy\u003c\/strong\u003e\u003cbr\u003e\u003c\/span\u003e\u003c\/span\u003e\u003c\/span\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eSet power alarm threshold\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003ePower\/Energy switch\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cspan lang=\"en\"\u003e\u003cspan lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e\u003cstrong\u003ePrecautions\u003c\/strong\u003e\u003cbr\u003e\u003c\/span\u003e\u003c\/span\u003e\u003c\/span\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eThis module is suitable for indoor, please do not use outdoor.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eApplied load should not exceed the rated power.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eWiring order can’t be wrong.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eSpecification parameters\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eWorking voltage: 80 ~ 260VAC\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eTest voltage: 80 ~ 260VAC\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eRated power: 22kW\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eOperating frequency: 45-65Hz\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eMeasurement accuracy: 1.0 grade \u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cspan lang=\"en\"\u003e\u003cspan lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e\u003cstrong\u003ePackage Included:\u003c\/strong\u003e\u003cbr\u003e\u003c\/span\u003e\u003c\/span\u003e\u003c\/span\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e1PC*100A AC 260V Digital LCD Panel Voltage Meter Power Energy Ammeter Voltmeter\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e","published_at":"2020-08-17T11:41:23+08:00","created_at":"2020-08-17T11:41:21+08:00","vendor":"DIYMORE","type":"","tags":[],"price":1399,"price_min":1399,"price_max":1399,"available":true,"price_varies":false,"compare_at_price":null,"compare_at_price_min":0,"compare_at_price_max":0,"compare_at_price_varies":false,"variants":[{"id":32513430552647,"title":"Default Title","option1":"Default Title","option2":null,"option3":null,"sku":"011748","requires_shipping":true,"taxable":false,"featured_image":null,"available":true,"name":"AC 260V 100A Digital LCD Panel Volt AMP Meter Power Energy Ammeter Voltmeter","public_title":null,"options":["Default Title"],"price":1399,"weight":100,"compare_at_price":null,"inventory_management":"shopify","barcode":"","requires_selling_plan":false,"selling_plan_allocations":[]}],"images":["\/\/www.diymore.cc\/cdn\/shop\/products\/011748_1.jpg?v=1597635684","\/\/www.diymore.cc\/cdn\/shop\/products\/011748_2.jpg?v=1597635684","\/\/www.diymore.cc\/cdn\/shop\/products\/011748_3.jpg?v=1597635684","\/\/www.diymore.cc\/cdn\/shop\/products\/011748_4.jpg?v=1597635684","\/\/www.diymore.cc\/cdn\/shop\/products\/011748_5.jpg?v=1597635684","\/\/www.diymore.cc\/cdn\/shop\/products\/011748_8.jpg?v=1597635684"],"featured_image":"\/\/www.diymore.cc\/cdn\/shop\/products\/011748_1.jpg?v=1597635684","options":["Title"],"media":[{"alt":null,"id":7291926872135,"position":1,"preview_image":{"aspect_ratio":1.25,"height":800,"width":1000,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011748_1.jpg?v=1597635684"},"aspect_ratio":1.25,"height":800,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011748_1.jpg?v=1597635684","width":1000},{"alt":null,"id":7291926904903,"position":2,"preview_image":{"aspect_ratio":1.253,"height":700,"width":877,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011748_2.jpg?v=1597635684"},"aspect_ratio":1.253,"height":700,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011748_2.jpg?v=1597635684","width":877},{"alt":null,"id":7291926937671,"position":3,"preview_image":{"aspect_ratio":1.238,"height":800,"width":990,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011748_3.jpg?v=1597635684"},"aspect_ratio":1.238,"height":800,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011748_3.jpg?v=1597635684","width":990},{"alt":null,"id":7291926970439,"position":4,"preview_image":{"aspect_ratio":1.255,"height":600,"width":753,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011748_4.jpg?v=1597635684"},"aspect_ratio":1.255,"height":600,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011748_4.jpg?v=1597635684","width":753},{"alt":null,"id":7291927003207,"position":5,"preview_image":{"aspect_ratio":1.252,"height":600,"width":751,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011748_5.jpg?v=1597635684"},"aspect_ratio":1.252,"height":600,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011748_5.jpg?v=1597635684","width":751},{"alt":null,"id":7291927035975,"position":6,"preview_image":{"aspect_ratio":1.154,"height":800,"width":923,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011748_8.jpg?v=1597635684"},"aspect_ratio":1.154,"height":800,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011748_8.jpg?v=1597635684","width":923}],"requires_selling_plan":false,"selling_plan_groups":[],"content":"\u003cspan lang=\"en\"\u003e\u003cspan lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e\u003cstrong\u003eDescription\u003c\/strong\u003e\u003cbr\u003e\u003cstrong\u003eA Function\u003c\/strong\u003e\u003cbr\u003e\u003c\/span\u003e\u003c\/span\u003e\u003c\/span\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eElectrical parameter measurement function (voltage, current, active power, energy)\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eOverload alarm function (over power alarm threshold, backlight and power flashing to alarm).\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003ePower alarm threshold preset function (can set power alarm threshold).\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eReset energy function.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eStore data when power off.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eSTN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e Backlight function.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cspan lang=\"en\"\u003e\u003cspan lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e\u003cstrong\u003eB. Appearance and Key function\u003c\/strong\u003e\u003cbr\u003e\u003c\/span\u003e\u003c\/span\u003e\u003c\/span\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eDisplay Interface\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cspan lang=\"en\"\u003e\u003cspan lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e\u003cstrong\u003eII.Display format\u003c\/strong\u003e\u003cbr\u003e\u003c\/span\u003e\u003c\/span\u003e\u003c\/span\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003ePower: test range: 0~22kW\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003ewithin 1KW, the display format is 0.0~999.9W;\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e1KW and above, the display format is 1000~9999W;\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e10kw and above, the display format is 10.0~22.0kW\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eEnergy: test range: 0~9999kWh\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eWithin 10KWh, the display format is 0~9999Wh;\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e10kWh and above, the display format is 10~9999kWh;\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eOver 9999kwh will return 0\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eVoltage: test range: 80~260V\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eDisplay format: 80~260V\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eCurrent: test range: 0~100A\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eDisplay format: 0.00~99.99A\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cspan lang=\"en\"\u003e\u003cspan lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e\u003cstrong\u003eIII. Key\u003c\/strong\u003e\u003cbr\u003e\u003c\/span\u003e\u003c\/span\u003e\u003c\/span\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eBacklight control\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cspan lang=\"en\"\u003e\u003cspan lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e\u003cstrong\u003eReset energy\u003c\/strong\u003e\u003cbr\u003e\u003c\/span\u003e\u003c\/span\u003e\u003c\/span\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eSet power alarm threshold\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003ePower\/Energy switch\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cspan lang=\"en\"\u003e\u003cspan lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e\u003cstrong\u003ePrecautions\u003c\/strong\u003e\u003cbr\u003e\u003c\/span\u003e\u003c\/span\u003e\u003c\/span\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eThis module is suitable for indoor, please do not use outdoor.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eApplied load should not exceed the rated power.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eWiring order can’t be wrong.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eSpecification parameters\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eWorking voltage: 80 ~ 260VAC\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eTest voltage: 80 ~ 260VAC\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eRated power: 22kW\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eOperating frequency: 45-65Hz\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eMeasurement accuracy: 1.0 grade \u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cspan lang=\"en\"\u003e\u003cspan lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e\u003cstrong\u003ePackage Included:\u003c\/strong\u003e\u003cbr\u003e\u003c\/span\u003e\u003c\/span\u003e\u003c\/span\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e1PC*100A AC 260V Digital LCD Panel Voltage Meter Power Energy Ammeter Voltmeter\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e"}
100A LCD Voltmeter Ammeter Volt Amp Power Kwh Panel Meter AC 80-300V/200-450V

Translation missing: en.products.product.regular_price $5.99
{"id":4795785936967,"title":"AC 260V 100A Digital LCD Panel Volt AMP Meter Power Energy Ammeter Voltmeter","handle":"ac-260v-100a-digital-lcd-panel-volt-amp-meter-power-energy-ammeter-voltmeter","description":"\u003cspan lang=\"en\"\u003e\u003cspan lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e\u003cstrong\u003eDescription\u003c\/strong\u003e\u003cbr\u003e\u003cstrong\u003eA Function\u003c\/strong\u003e\u003cbr\u003e\u003c\/span\u003e\u003c\/span\u003e\u003c\/span\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eElectrical parameter measurement function (voltage, current, active power, energy)\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eOverload alarm function (over power alarm threshold, backlight and power flashing to alarm).\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003ePower alarm threshold preset function (can set power alarm threshold).\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eReset energy function.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eStore data when power off.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eSTN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e Backlight function.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cspan lang=\"en\"\u003e\u003cspan lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e\u003cstrong\u003eB. Appearance and Key function\u003c\/strong\u003e\u003cbr\u003e\u003c\/span\u003e\u003c\/span\u003e\u003c\/span\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eDisplay Interface\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cspan lang=\"en\"\u003e\u003cspan lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e\u003cstrong\u003eII.Display format\u003c\/strong\u003e\u003cbr\u003e\u003c\/span\u003e\u003c\/span\u003e\u003c\/span\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003ePower: test range: 0~22kW\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003ewithin 1KW, the display format is 0.0~999.9W;\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e1KW and above, the display format is 1000~9999W;\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e10kw and above, the display format is 10.0~22.0kW\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eEnergy: test range: 0~9999kWh\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eWithin 10KWh, the display format is 0~9999Wh;\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e10kWh and above, the display format is 10~9999kWh;\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eOver 9999kwh will return 0\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eVoltage: test range: 80~260V\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eDisplay format: 80~260V\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eCurrent: test range: 0~100A\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eDisplay format: 0.00~99.99A\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cspan lang=\"en\"\u003e\u003cspan lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e\u003cstrong\u003eIII. Key\u003c\/strong\u003e\u003cbr\u003e\u003c\/span\u003e\u003c\/span\u003e\u003c\/span\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eBacklight control\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cspan lang=\"en\"\u003e\u003cspan lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e\u003cstrong\u003eReset energy\u003c\/strong\u003e\u003cbr\u003e\u003c\/span\u003e\u003c\/span\u003e\u003c\/span\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eSet power alarm threshold\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003ePower\/Energy switch\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cspan lang=\"en\"\u003e\u003cspan lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e\u003cstrong\u003ePrecautions\u003c\/strong\u003e\u003cbr\u003e\u003c\/span\u003e\u003c\/span\u003e\u003c\/span\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eThis module is suitable for indoor, please do not use outdoor.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eApplied load should not exceed the rated power.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eWiring order can’t be wrong.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eSpecification parameters\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eWorking voltage: 80 ~ 260VAC\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eTest voltage: 80 ~ 260VAC\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eRated power: 22kW\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eOperating frequency: 45-65Hz\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eMeasurement accuracy: 1.0 grade \u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cspan lang=\"en\"\u003e\u003cspan lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e\u003cstrong\u003ePackage Included:\u003c\/strong\u003e\u003cbr\u003e\u003c\/span\u003e\u003c\/span\u003e\u003c\/span\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e1PC*100A AC 260V Digital LCD Panel Voltage Meter Power Energy Ammeter Voltmeter\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e","published_at":"2020-08-17T11:41:23+08:00","created_at":"2020-08-17T11:41:21+08:00","vendor":"DIYMORE","type":"","tags":[],"price":1399,"price_min":1399,"price_max":1399,"available":true,"price_varies":false,"compare_at_price":null,"compare_at_price_min":0,"compare_at_price_max":0,"compare_at_price_varies":false,"variants":[{"id":32513430552647,"title":"Default Title","option1":"Default Title","option2":null,"option3":null,"sku":"011748","requires_shipping":true,"taxable":false,"featured_image":null,"available":true,"name":"AC 260V 100A Digital LCD Panel Volt AMP Meter Power Energy Ammeter Voltmeter","public_title":null,"options":["Default Title"],"price":1399,"weight":100,"compare_at_price":null,"inventory_management":"shopify","barcode":"","requires_selling_plan":false,"selling_plan_allocations":[]}],"images":["\/\/www.diymore.cc\/cdn\/shop\/products\/011748_1.jpg?v=1597635684","\/\/www.diymore.cc\/cdn\/shop\/products\/011748_2.jpg?v=1597635684","\/\/www.diymore.cc\/cdn\/shop\/products\/011748_3.jpg?v=1597635684","\/\/www.diymore.cc\/cdn\/shop\/products\/011748_4.jpg?v=1597635684","\/\/www.diymore.cc\/cdn\/shop\/products\/011748_5.jpg?v=1597635684","\/\/www.diymore.cc\/cdn\/shop\/products\/011748_8.jpg?v=1597635684"],"featured_image":"\/\/www.diymore.cc\/cdn\/shop\/products\/011748_1.jpg?v=1597635684","options":["Title"],"media":[{"alt":null,"id":7291926872135,"position":1,"preview_image":{"aspect_ratio":1.25,"height":800,"width":1000,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011748_1.jpg?v=1597635684"},"aspect_ratio":1.25,"height":800,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011748_1.jpg?v=1597635684","width":1000},{"alt":null,"id":7291926904903,"position":2,"preview_image":{"aspect_ratio":1.253,"height":700,"width":877,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011748_2.jpg?v=1597635684"},"aspect_ratio":1.253,"height":700,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011748_2.jpg?v=1597635684","width":877},{"alt":null,"id":7291926937671,"position":3,"preview_image":{"aspect_ratio":1.238,"height":800,"width":990,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011748_3.jpg?v=1597635684"},"aspect_ratio":1.238,"height":800,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011748_3.jpg?v=1597635684","width":990},{"alt":null,"id":7291926970439,"position":4,"preview_image":{"aspect_ratio":1.255,"height":600,"width":753,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011748_4.jpg?v=1597635684"},"aspect_ratio":1.255,"height":600,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011748_4.jpg?v=1597635684","width":753},{"alt":null,"id":7291927003207,"position":5,"preview_image":{"aspect_ratio":1.252,"height":600,"width":751,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011748_5.jpg?v=1597635684"},"aspect_ratio":1.252,"height":600,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011748_5.jpg?v=1597635684","width":751},{"alt":null,"id":7291927035975,"position":6,"preview_image":{"aspect_ratio":1.154,"height":800,"width":923,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011748_8.jpg?v=1597635684"},"aspect_ratio":1.154,"height":800,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011748_8.jpg?v=1597635684","width":923}],"requires_selling_plan":false,"selling_plan_groups":[],"content":"\u003cspan lang=\"en\"\u003e\u003cspan lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e\u003cstrong\u003eDescription\u003c\/strong\u003e\u003cbr\u003e\u003cstrong\u003eA Function\u003c\/strong\u003e\u003cbr\u003e\u003c\/span\u003e\u003c\/span\u003e\u003c\/span\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eElectrical parameter measurement function (voltage, current, active power, energy)\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eOverload alarm function (over power alarm threshold, backlight and power flashing to alarm).\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003ePower alarm threshold preset function (can set power alarm threshold).\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eReset energy function.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eStore data when power off.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eSTN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e Backlight function.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cspan lang=\"en\"\u003e\u003cspan lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e\u003cstrong\u003eB. Appearance and Key function\u003c\/strong\u003e\u003cbr\u003e\u003c\/span\u003e\u003c\/span\u003e\u003c\/span\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eDisplay Interface\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cspan lang=\"en\"\u003e\u003cspan lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e\u003cstrong\u003eII.Display format\u003c\/strong\u003e\u003cbr\u003e\u003c\/span\u003e\u003c\/span\u003e\u003c\/span\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003ePower: test range: 0~22kW\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003ewithin 1KW, the display format is 0.0~999.9W;\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e1KW and above, the display format is 1000~9999W;\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e10kw and above, the display format is 10.0~22.0kW\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eEnergy: test range: 0~9999kWh\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eWithin 10KWh, the display format is 0~9999Wh;\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e10kWh and above, the display format is 10~9999kWh;\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eOver 9999kwh will return 0\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eVoltage: test range: 80~260V\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eDisplay format: 80~260V\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eCurrent: test range: 0~100A\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eDisplay format: 0.00~99.99A\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cspan lang=\"en\"\u003e\u003cspan lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e\u003cstrong\u003eIII. Key\u003c\/strong\u003e\u003cbr\u003e\u003c\/span\u003e\u003c\/span\u003e\u003c\/span\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eBacklight control\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cspan lang=\"en\"\u003e\u003cspan lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e\u003cstrong\u003eReset energy\u003c\/strong\u003e\u003cbr\u003e\u003c\/span\u003e\u003c\/span\u003e\u003c\/span\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eSet power alarm threshold\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003ePower\/Energy switch\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cspan lang=\"en\"\u003e\u003cspan lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e\u003cstrong\u003ePrecautions\u003c\/strong\u003e\u003cbr\u003e\u003c\/span\u003e\u003c\/span\u003e\u003c\/span\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eThis module is suitable for indoor, please do not use outdoor.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eApplied load should not exceed the rated power.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eWiring order can’t be wrong.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eSpecification parameters\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eWorking voltage: 80 ~ 260VAC\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eTest voltage: 80 ~ 260VAC\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eRated power: 22kW\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eOperating frequency: 45-65Hz\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eMeasurement accuracy: 1.0 grade \u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cspan lang=\"en\"\u003e\u003cspan lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e\u003cstrong\u003ePackage Included:\u003c\/strong\u003e\u003cbr\u003e\u003c\/span\u003e\u003c\/span\u003e\u003c\/span\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e1PC*100A AC 260V Digital LCD Panel Voltage Meter Power Energy Ammeter Voltmeter\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e"}
W3230 DC 12V/24V AC110V-220V Digital LCD Thermostat Temperature Controller

Translation missing: en.products.product.regular_price $8.99
{"id":4795785936967,"title":"AC 260V 100A Digital LCD Panel Volt AMP Meter Power Energy Ammeter Voltmeter","handle":"ac-260v-100a-digital-lcd-panel-volt-amp-meter-power-energy-ammeter-voltmeter","description":"\u003cspan lang=\"en\"\u003e\u003cspan lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e\u003cstrong\u003eDescription\u003c\/strong\u003e\u003cbr\u003e\u003cstrong\u003eA Function\u003c\/strong\u003e\u003cbr\u003e\u003c\/span\u003e\u003c\/span\u003e\u003c\/span\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eElectrical parameter measurement function (voltage, current, active power, energy)\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eOverload alarm function (over power alarm threshold, backlight and power flashing to alarm).\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003ePower alarm threshold preset function (can set power alarm threshold).\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eReset energy function.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eStore data when power off.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eSTN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e Backlight function.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cspan lang=\"en\"\u003e\u003cspan lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e\u003cstrong\u003eB. Appearance and Key function\u003c\/strong\u003e\u003cbr\u003e\u003c\/span\u003e\u003c\/span\u003e\u003c\/span\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eDisplay Interface\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cspan lang=\"en\"\u003e\u003cspan lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e\u003cstrong\u003eII.Display format\u003c\/strong\u003e\u003cbr\u003e\u003c\/span\u003e\u003c\/span\u003e\u003c\/span\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003ePower: test range: 0~22kW\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003ewithin 1KW, the display format is 0.0~999.9W;\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e1KW and above, the display format is 1000~9999W;\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e10kw and above, the display format is 10.0~22.0kW\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eEnergy: test range: 0~9999kWh\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eWithin 10KWh, the display format is 0~9999Wh;\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e10kWh and above, the display format is 10~9999kWh;\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eOver 9999kwh will return 0\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eVoltage: test range: 80~260V\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eDisplay format: 80~260V\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eCurrent: test range: 0~100A\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eDisplay format: 0.00~99.99A\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cspan lang=\"en\"\u003e\u003cspan lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e\u003cstrong\u003eIII. Key\u003c\/strong\u003e\u003cbr\u003e\u003c\/span\u003e\u003c\/span\u003e\u003c\/span\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eBacklight control\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cspan lang=\"en\"\u003e\u003cspan lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e\u003cstrong\u003eReset energy\u003c\/strong\u003e\u003cbr\u003e\u003c\/span\u003e\u003c\/span\u003e\u003c\/span\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eSet power alarm threshold\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003ePower\/Energy switch\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cspan lang=\"en\"\u003e\u003cspan lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e\u003cstrong\u003ePrecautions\u003c\/strong\u003e\u003cbr\u003e\u003c\/span\u003e\u003c\/span\u003e\u003c\/span\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eThis module is suitable for indoor, please do not use outdoor.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eApplied load should not exceed the rated power.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eWiring order can’t be wrong.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eSpecification parameters\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eWorking voltage: 80 ~ 260VAC\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eTest voltage: 80 ~ 260VAC\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eRated power: 22kW\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eOperating frequency: 45-65Hz\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eMeasurement accuracy: 1.0 grade \u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cspan lang=\"en\"\u003e\u003cspan lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e\u003cstrong\u003ePackage Included:\u003c\/strong\u003e\u003cbr\u003e\u003c\/span\u003e\u003c\/span\u003e\u003c\/span\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e1PC*100A AC 260V Digital LCD Panel Voltage Meter Power Energy Ammeter Voltmeter\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e","published_at":"2020-08-17T11:41:23+08:00","created_at":"2020-08-17T11:41:21+08:00","vendor":"DIYMORE","type":"","tags":[],"price":1399,"price_min":1399,"price_max":1399,"available":true,"price_varies":false,"compare_at_price":null,"compare_at_price_min":0,"compare_at_price_max":0,"compare_at_price_varies":false,"variants":[{"id":32513430552647,"title":"Default Title","option1":"Default Title","option2":null,"option3":null,"sku":"011748","requires_shipping":true,"taxable":false,"featured_image":null,"available":true,"name":"AC 260V 100A Digital LCD Panel Volt AMP Meter Power Energy Ammeter Voltmeter","public_title":null,"options":["Default Title"],"price":1399,"weight":100,"compare_at_price":null,"inventory_management":"shopify","barcode":"","requires_selling_plan":false,"selling_plan_allocations":[]}],"images":["\/\/www.diymore.cc\/cdn\/shop\/products\/011748_1.jpg?v=1597635684","\/\/www.diymore.cc\/cdn\/shop\/products\/011748_2.jpg?v=1597635684","\/\/www.diymore.cc\/cdn\/shop\/products\/011748_3.jpg?v=1597635684","\/\/www.diymore.cc\/cdn\/shop\/products\/011748_4.jpg?v=1597635684","\/\/www.diymore.cc\/cdn\/shop\/products\/011748_5.jpg?v=1597635684","\/\/www.diymore.cc\/cdn\/shop\/products\/011748_8.jpg?v=1597635684"],"featured_image":"\/\/www.diymore.cc\/cdn\/shop\/products\/011748_1.jpg?v=1597635684","options":["Title"],"media":[{"alt":null,"id":7291926872135,"position":1,"preview_image":{"aspect_ratio":1.25,"height":800,"width":1000,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011748_1.jpg?v=1597635684"},"aspect_ratio":1.25,"height":800,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011748_1.jpg?v=1597635684","width":1000},{"alt":null,"id":7291926904903,"position":2,"preview_image":{"aspect_ratio":1.253,"height":700,"width":877,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011748_2.jpg?v=1597635684"},"aspect_ratio":1.253,"height":700,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011748_2.jpg?v=1597635684","width":877},{"alt":null,"id":7291926937671,"position":3,"preview_image":{"aspect_ratio":1.238,"height":800,"width":990,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011748_3.jpg?v=1597635684"},"aspect_ratio":1.238,"height":800,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011748_3.jpg?v=1597635684","width":990},{"alt":null,"id":7291926970439,"position":4,"preview_image":{"aspect_ratio":1.255,"height":600,"width":753,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011748_4.jpg?v=1597635684"},"aspect_ratio":1.255,"height":600,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011748_4.jpg?v=1597635684","width":753},{"alt":null,"id":7291927003207,"position":5,"preview_image":{"aspect_ratio":1.252,"height":600,"width":751,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011748_5.jpg?v=1597635684"},"aspect_ratio":1.252,"height":600,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011748_5.jpg?v=1597635684","width":751},{"alt":null,"id":7291927035975,"position":6,"preview_image":{"aspect_ratio":1.154,"height":800,"width":923,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011748_8.jpg?v=1597635684"},"aspect_ratio":1.154,"height":800,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011748_8.jpg?v=1597635684","width":923}],"requires_selling_plan":false,"selling_plan_groups":[],"content":"\u003cspan lang=\"en\"\u003e\u003cspan lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e\u003cstrong\u003eDescription\u003c\/strong\u003e\u003cbr\u003e\u003cstrong\u003eA Function\u003c\/strong\u003e\u003cbr\u003e\u003c\/span\u003e\u003c\/span\u003e\u003c\/span\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eElectrical parameter measurement function (voltage, current, active power, energy)\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eOverload alarm function (over power alarm threshold, backlight and power flashing to alarm).\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003ePower alarm threshold preset function (can set power alarm threshold).\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eReset energy function.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eStore data when power off.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eSTN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e Backlight function.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cspan lang=\"en\"\u003e\u003cspan lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e\u003cstrong\u003eB. Appearance and Key function\u003c\/strong\u003e\u003cbr\u003e\u003c\/span\u003e\u003c\/span\u003e\u003c\/span\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eDisplay Interface\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cspan lang=\"en\"\u003e\u003cspan lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e\u003cstrong\u003eII.Display format\u003c\/strong\u003e\u003cbr\u003e\u003c\/span\u003e\u003c\/span\u003e\u003c\/span\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003ePower: test range: 0~22kW\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003ewithin 1KW, the display format is 0.0~999.9W;\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e1KW and above, the display format is 1000~9999W;\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e10kw and above, the display format is 10.0~22.0kW\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eEnergy: test range: 0~9999kWh\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eWithin 10KWh, the display format is 0~9999Wh;\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e10kWh and above, the display format is 10~9999kWh;\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eOver 9999kwh will return 0\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eVoltage: test range: 80~260V\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eDisplay format: 80~260V\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eCurrent: test range: 0~100A\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eDisplay format: 0.00~99.99A\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cspan lang=\"en\"\u003e\u003cspan lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e\u003cstrong\u003eIII. Key\u003c\/strong\u003e\u003cbr\u003e\u003c\/span\u003e\u003c\/span\u003e\u003c\/span\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eBacklight control\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cspan lang=\"en\"\u003e\u003cspan lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e\u003cstrong\u003eReset energy\u003c\/strong\u003e\u003cbr\u003e\u003c\/span\u003e\u003c\/span\u003e\u003c\/span\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eSet power alarm threshold\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003ePower\/Energy switch\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cspan lang=\"en\"\u003e\u003cspan lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e\u003cstrong\u003ePrecautions\u003c\/strong\u003e\u003cbr\u003e\u003c\/span\u003e\u003c\/span\u003e\u003c\/span\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eThis module is suitable for indoor, please do not use outdoor.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eApplied load should not exceed the rated power.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eWiring order can’t be wrong.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eSpecification parameters\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eWorking voltage: 80 ~ 260VAC\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eTest voltage: 80 ~ 260VAC\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eRated power: 22kW\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eOperating frequency: 45-65Hz\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eMeasurement accuracy: 1.0 grade \u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cspan lang=\"en\"\u003e\u003cspan lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e\u003cstrong\u003ePackage Included:\u003c\/strong\u003e\u003cbr\u003e\u003c\/span\u003e\u003c\/span\u003e\u003c\/span\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e1PC*100A AC 260V Digital LCD Panel Voltage Meter Power Energy Ammeter Voltmeter\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e"}
1602 16X2 LCD IIC/I2C/TWI/SPI Serial Interface Module Display Blue/Yellow

Translation missing: en.products.product.regular_price $6.99
{"id":4795785936967,"title":"AC 260V 100A Digital LCD Panel Volt AMP Meter Power Energy Ammeter Voltmeter","handle":"ac-260v-100a-digital-lcd-panel-volt-amp-meter-power-energy-ammeter-voltmeter","description":"\u003cspan lang=\"en\"\u003e\u003cspan lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e\u003cstrong\u003eDescription\u003c\/strong\u003e\u003cbr\u003e\u003cstrong\u003eA Function\u003c\/strong\u003e\u003cbr\u003e\u003c\/span\u003e\u003c\/span\u003e\u003c\/span\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eElectrical parameter measurement function (voltage, current, active power, energy)\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eOverload alarm function (over power alarm threshold, backlight and power flashing to alarm).\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003ePower alarm threshold preset function (can set power alarm threshold).\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eReset energy function.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eStore data when power off.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eSTN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e Backlight function.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cspan lang=\"en\"\u003e\u003cspan lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e\u003cstrong\u003eB. Appearance and Key function\u003c\/strong\u003e\u003cbr\u003e\u003c\/span\u003e\u003c\/span\u003e\u003c\/span\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eDisplay Interface\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cspan lang=\"en\"\u003e\u003cspan lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e\u003cstrong\u003eII.Display format\u003c\/strong\u003e\u003cbr\u003e\u003c\/span\u003e\u003c\/span\u003e\u003c\/span\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003ePower: test range: 0~22kW\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003ewithin 1KW, the display format is 0.0~999.9W;\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e1KW and above, the display format is 1000~9999W;\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e10kw and above, the display format is 10.0~22.0kW\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eEnergy: test range: 0~9999kWh\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eWithin 10KWh, the display format is 0~9999Wh;\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e10kWh and above, the display format is 10~9999kWh;\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eOver 9999kwh will return 0\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eVoltage: test range: 80~260V\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eDisplay format: 80~260V\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eCurrent: test range: 0~100A\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eDisplay format: 0.00~99.99A\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cspan lang=\"en\"\u003e\u003cspan lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e\u003cstrong\u003eIII. Key\u003c\/strong\u003e\u003cbr\u003e\u003c\/span\u003e\u003c\/span\u003e\u003c\/span\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eBacklight control\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cspan lang=\"en\"\u003e\u003cspan lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e\u003cstrong\u003eReset energy\u003c\/strong\u003e\u003cbr\u003e\u003c\/span\u003e\u003c\/span\u003e\u003c\/span\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eSet power alarm threshold\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003ePower\/Energy switch\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cspan lang=\"en\"\u003e\u003cspan lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e\u003cstrong\u003ePrecautions\u003c\/strong\u003e\u003cbr\u003e\u003c\/span\u003e\u003c\/span\u003e\u003c\/span\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eThis module is suitable for indoor, please do not use outdoor.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eApplied load should not exceed the rated power.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eWiring order can’t be wrong.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eSpecification parameters\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eWorking voltage: 80 ~ 260VAC\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eTest voltage: 80 ~ 260VAC\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eRated power: 22kW\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eOperating frequency: 45-65Hz\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eMeasurement accuracy: 1.0 grade \u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cspan lang=\"en\"\u003e\u003cspan lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e\u003cstrong\u003ePackage Included:\u003c\/strong\u003e\u003cbr\u003e\u003c\/span\u003e\u003c\/span\u003e\u003c\/span\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e1PC*100A AC 260V Digital LCD Panel Voltage Meter Power Energy Ammeter Voltmeter\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e","published_at":"2020-08-17T11:41:23+08:00","created_at":"2020-08-17T11:41:21+08:00","vendor":"DIYMORE","type":"","tags":[],"price":1399,"price_min":1399,"price_max":1399,"available":true,"price_varies":false,"compare_at_price":null,"compare_at_price_min":0,"compare_at_price_max":0,"compare_at_price_varies":false,"variants":[{"id":32513430552647,"title":"Default Title","option1":"Default Title","option2":null,"option3":null,"sku":"011748","requires_shipping":true,"taxable":false,"featured_image":null,"available":true,"name":"AC 260V 100A Digital LCD Panel Volt AMP Meter Power Energy Ammeter Voltmeter","public_title":null,"options":["Default Title"],"price":1399,"weight":100,"compare_at_price":null,"inventory_management":"shopify","barcode":"","requires_selling_plan":false,"selling_plan_allocations":[]}],"images":["\/\/www.diymore.cc\/cdn\/shop\/products\/011748_1.jpg?v=1597635684","\/\/www.diymore.cc\/cdn\/shop\/products\/011748_2.jpg?v=1597635684","\/\/www.diymore.cc\/cdn\/shop\/products\/011748_3.jpg?v=1597635684","\/\/www.diymore.cc\/cdn\/shop\/products\/011748_4.jpg?v=1597635684","\/\/www.diymore.cc\/cdn\/shop\/products\/011748_5.jpg?v=1597635684","\/\/www.diymore.cc\/cdn\/shop\/products\/011748_8.jpg?v=1597635684"],"featured_image":"\/\/www.diymore.cc\/cdn\/shop\/products\/011748_1.jpg?v=1597635684","options":["Title"],"media":[{"alt":null,"id":7291926872135,"position":1,"preview_image":{"aspect_ratio":1.25,"height":800,"width":1000,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011748_1.jpg?v=1597635684"},"aspect_ratio":1.25,"height":800,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011748_1.jpg?v=1597635684","width":1000},{"alt":null,"id":7291926904903,"position":2,"preview_image":{"aspect_ratio":1.253,"height":700,"width":877,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011748_2.jpg?v=1597635684"},"aspect_ratio":1.253,"height":700,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011748_2.jpg?v=1597635684","width":877},{"alt":null,"id":7291926937671,"position":3,"preview_image":{"aspect_ratio":1.238,"height":800,"width":990,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011748_3.jpg?v=1597635684"},"aspect_ratio":1.238,"height":800,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011748_3.jpg?v=1597635684","width":990},{"alt":null,"id":7291926970439,"position":4,"preview_image":{"aspect_ratio":1.255,"height":600,"width":753,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011748_4.jpg?v=1597635684"},"aspect_ratio":1.255,"height":600,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011748_4.jpg?v=1597635684","width":753},{"alt":null,"id":7291927003207,"position":5,"preview_image":{"aspect_ratio":1.252,"height":600,"width":751,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011748_5.jpg?v=1597635684"},"aspect_ratio":1.252,"height":600,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011748_5.jpg?v=1597635684","width":751},{"alt":null,"id":7291927035975,"position":6,"preview_image":{"aspect_ratio":1.154,"height":800,"width":923,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011748_8.jpg?v=1597635684"},"aspect_ratio":1.154,"height":800,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011748_8.jpg?v=1597635684","width":923}],"requires_selling_plan":false,"selling_plan_groups":[],"content":"\u003cspan lang=\"en\"\u003e\u003cspan lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e\u003cstrong\u003eDescription\u003c\/strong\u003e\u003cbr\u003e\u003cstrong\u003eA Function\u003c\/strong\u003e\u003cbr\u003e\u003c\/span\u003e\u003c\/span\u003e\u003c\/span\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eElectrical parameter measurement function (voltage, current, active power, energy)\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eOverload alarm function (over power alarm threshold, backlight and power flashing to alarm).\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003ePower alarm threshold preset function (can set power alarm threshold).\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eReset energy function.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eStore data when power off.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eSTN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e Backlight function.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cspan lang=\"en\"\u003e\u003cspan lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e\u003cstrong\u003eB. Appearance and Key function\u003c\/strong\u003e\u003cbr\u003e\u003c\/span\u003e\u003c\/span\u003e\u003c\/span\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eDisplay Interface\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cspan lang=\"en\"\u003e\u003cspan lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e\u003cstrong\u003eII.Display format\u003c\/strong\u003e\u003cbr\u003e\u003c\/span\u003e\u003c\/span\u003e\u003c\/span\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003ePower: test range: 0~22kW\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003ewithin 1KW, the display format is 0.0~999.9W;\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e1KW and above, the display format is 1000~9999W;\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e10kw and above, the display format is 10.0~22.0kW\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eEnergy: test range: 0~9999kWh\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eWithin 10KWh, the display format is 0~9999Wh;\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e10kWh and above, the display format is 10~9999kWh;\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eOver 9999kwh will return 0\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eVoltage: test range: 80~260V\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eDisplay format: 80~260V\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eCurrent: test range: 0~100A\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eDisplay format: 0.00~99.99A\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cspan lang=\"en\"\u003e\u003cspan lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e\u003cstrong\u003eIII. Key\u003c\/strong\u003e\u003cbr\u003e\u003c\/span\u003e\u003c\/span\u003e\u003c\/span\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eBacklight control\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cspan lang=\"en\"\u003e\u003cspan lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e\u003cstrong\u003eReset energy\u003c\/strong\u003e\u003cbr\u003e\u003c\/span\u003e\u003c\/span\u003e\u003c\/span\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eSet power alarm threshold\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003ePower\/Energy switch\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cspan lang=\"en\"\u003e\u003cspan lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e\u003cstrong\u003ePrecautions\u003c\/strong\u003e\u003cbr\u003e\u003c\/span\u003e\u003c\/span\u003e\u003c\/span\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eThis module is suitable for indoor, please do not use outdoor.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eApplied load should not exceed the rated power.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eWiring order can’t be wrong.\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eSpecification parameters\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eWorking voltage: 80 ~ 260VAC\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eTest voltage: 80 ~ 260VAC\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eRated power: 22kW\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eOperating frequency: 45-65Hz\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003eMeasurement accuracy: 1.0 grade \u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cspan lang=\"en\"\u003e\u003cspan lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e\u003cstrong\u003ePackage Included:\u003c\/strong\u003e\u003cbr\u003e\u003c\/span\u003e\u003c\/span\u003e\u003c\/span\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cspan id=\"result_box\" lang=\"en\"\u003e\u003cspan title=\"Description\nA Function\n1. Electrical parameter measurement function (voltage, current, active power, energy)\n2. Overload alarm function (over power alarm threshold, backlight and power flashing to alarm).\n3. Power alarm threshold preset function (can set power alarm threshold).\n4. Reset energy function.\n5. Store data when power off.\n6. STN whole viewing angleLCD (display voltage, current, active power\/energy at the same time)\n7. Backlight function.\nB. Appearance and Key function\nI. Display Interface\nThe large-screen STN whole viewing angle LCD can display voltage, current, power, energy at the same time.(note: power and energy display can be switched by the key.)\nII.Display format\n\n1.Power: test range: 0~22kW\nwithin 1KW, the display format is 0.0~999.9W;\n1KW and above, the display format is 1000~9999W;\n10kw and above, the display format is 10.0~22.0kW\n2.Energy: test range: 0~9999kWh\nWithin 10KWh, the display format is 0~9999Wh;\n10kWh and above, the display format is 10~9999kWh;\nOver 9999kwh will return 0\n3. Voltage: test range: 80~260V\nDisplay format: 80~260V\n4. Current: test range: 0~100A\nDisplay format: 0.00~99.99A\nIII. Key\n1. Backlight control\nShort press the key to turn on or off the backlight, the backlight has memory function, it can store the on or off state when power off.\n2. Reset energy\nStep1: Long press the key at least3 seconds until the number in energy display area flash, then release the key.\nStep2: If short press the key again, then the energy value is cleared and exit the reset state.If short press the key again, then the energy value will not be cleared and will exit the reset state. If there is no operation on the key within 10 seconds, the energy value will not be cleared and will exit the reset state.\n3. Set power alarm threshold\nStep1: Long press the key at least 3 seconds until the number in power display area flash,then release the key\nStep2: Powerarea display the current power alarm value and the last digit begin to flash, then you can short press the key to plus 1, short press the key can switch the digit which you want to set. The threshold can’t be over 25kw( note: the default value is 25kw)\n\nStep3: After finish the setting, long press the key over 3 seconds or there is no operation over 10 seconds, it will store data automatically and exit the set state.\n4. Power\/Energy switch\nYou can short press the key to switch display the power\/ energy, the display state will be store when power off.\nC. Precautions\n1. This module is suitable for indoor, please do not use outdoor.\n2. Applied load should not exceed the rated power.\n3. Wiring order can’t be wrong.\nD. Specification parameters\n1. Working voltage: 80 ~ 260VAC\n2. Test voltage: 80 ~ 260VAC\n3. Rated power: 22kW\n4. Operating frequency: 45-65Hz\n5. Measurement accuracy: 1.0 grade \n\nPackage Included:\n1PC*\"\u003e1PC*100A AC 260V Digital LCD Panel Voltage Meter Power Energy Ammeter Voltmeter\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e"}